Jump to content

HMS Naiad 1797 by GDM67 - 1:60 - using Ed Tosti Books


Recommended Posts

  • 3 months later...

Hi Kees,  Sorry not to reply sooner.  That family stuff has really got me becalmed.  Yes, I stand over my model.  At some point, I imagine I will sit down, but have done all my modeling while standing to this point.  I guess it has a lot to do with the fact that I sit at my computer for 8-10 hours each day at work.

 

I have made little progress on Naiad since November, but am still an avid builder.  Photos when there is something worth sharing.

 

Thanks for commenting!  G

Link to comment
Share on other sites

  • 1 month later...

Hi All,

 

I'm back!  I took a little break but am now back in the shop and going strong. 

 

530 hours into the journey.  I decided to shift away from the hull work and tackle a little of the inside.  I had several reasons, the real one being that I needed a change of scenery.  That being said, I wanted to stiffen the hull before doing final sanding.  To do that, I laid the keelson, ceiling planks, crutches and breast hooks.  I then built up part of the magazine while I was on a roll.


Ed suggests building the forward magazine while off the model.  I think this was a great idea and it allowed me to work freely at the bench.  At some point, the magazine will be installed, but first I need to lay the orlop deck beams.  There is a critical relationship here that you need to get right.  My version of the magazine has simple detail elements.  I decided not to treenail at the lower depths and decided to simplify the number of beams on the sb side.  This being said, I will increase the detail as I climb.  I enjoyed making the magazine substructure. It was a unique challenge.  And, looks much better to the naked eye - these photos are unforgiving.  I wanted clean detail, but I am not obsessing on my work here.  The black area is simulated charcoal.  I simply took 500 grit wet sandpaper and applied it here.  I doubt you will be able to see it on the finished model, but thought it would be a nice detail to discuss.315.JPG318.thumb.JPG.e82aea07f9cd5a88af087225e735b8c4.JPG

328.thumb.JPG.2e60e870e9ec77ace3070e26b75f4b9e.JPG

329.thumb.JPG.98417276845fa232fbd6badf75d170f0.JPGThe ceiling planks were a special challenge when it came to clamping.  I made great use of the gantry system when securing these planks.  Its amazing how stiff the hull is with these structures in place.  While I would not want to step on the model, it does give you appreciable insight into the durability of the actual ship.245.thumb.JPG.72f8734d89e9f9282c26bd15b8ec1b55.JPG 

As I reflect further on building an extreme POF ship, one of the many things I like about it is that you don't simply glue pieces together, but rather think about how they would have worked together on the real ship.  My skills have improved since I have been forced to think differently about the ship.

 

Hope to have more soon!

 

All the best, Gary

Link to comment
Share on other sites

Link to comment
Share on other sites

  • 2 weeks later...

Hi All,  I am now 565 hours into the journey of Naiad over the last 16-months.  Feeling good about where I am thus far.  Since my last post, I have completed the gun ports on the p/s and have completed the sills on the s/b side.

 

In this first photo, is my small cutting board clamped to the build board.  Note the half cup in the far corner.  This is screwed to the board and I insert the larger cup of water in it.  I use the water to wash off excess glue.  I was tired of spilling it all the time.  Also, I mounted a pencil holder and caliper holder to each side of the build board.  I am trying to train myself to put these items back after each use.  I figure this will save me thousands of hours of having to looking for pencils and calipers. (I don't know why this text got underlined, oh well...)593820201d568_GaryCellUploadJune2017036.thumb.JPG.6019fb4cff0c23a9f99833823539ca8f.JPG593820223b51c_GaryCellUploadJune2017037.thumb.JPG.f3b8c547dd1504534968b16ea79f4b5e.JPG5938202613895_GaryCellUploadJune2017039.thumb.JPG.17f2fab7b811bf699417a7740a4a09cb.JPG

 

 

I built these measuring calipers at the start of the build as recommended by Ed. They are lap jointed and pinned and have proved to be invaluable.  I used scrap babinga wood.  Recently, I added a brass strip for the screw to clamp down on.  This has limited the movement of the caliper once tightened.5938202a55881_GaryCellUploadJune2017041.thumb.JPG.7f08f60f4e0dd8d2eb69baa4d6583155.JPG

As I placed each sill, I would use strips of bass wood as a "winding stick" to check for level from sill to sill.  I am very happy with the results and have recreated the slope of the sills as outlined in the plans.  There is a gentle rise at the ends of the ship with a low-level valley at midship.   There is probably a nautical term for this sweep. I still need to fair the inside of the top timbers.

 

5938202c8ea26_GaryCellUploadJune2017042.thumb.JPG.ad0b709483fca60bc8890a3eda36acf3.JPG

While this picture is upside down, it shows the squareness of the gun ports.  I cannot emphasize enough that each piece you place is of great importance to the overall symmetry in a build like this.  Mistakes, no matter how random or remote will likely be magnified somewhere else in the build.

 

5938202f0262d_GaryCellUploadJune2017043.thumb.JPG.3b9e1445b4610faf25ba36907d25b2f6.JPGThis is just an exterior portside view of the gun ports and illustrates the gentle sweep of the ports. Yes, that's a dead rat hanging from the light... fake of course...5938201bc9ba1_GaryCellUploadJune2017034.thumb.JPG.77a0f690d656dd5aa0993b459bfda1d2.JPG

I used pinstripe tape to establish the fair sweep of the sills.  The sills remain horizontal throughout the ship,  the sweep is very subtle.

 59382019c203d_GaryCellUploadJune2017033.thumb.JPG.dc924e9bce10d8b8bb07d546b07d9da0.JPG

59381fe4064fb_GaryCellUploadJune2017032.thumb.JPG.821826613fdc7560e888404d1c810585.JPG

You will note the use of a spacer block for the ports.  I found this essential I getting the correct length and height of each port.  I colored the block so I could easily find it among all my scraps.  Yes, I uploaded these photos backwards...
 

Gary Cell Upload June 2017 038.JPG

Next on the to do list is to finish the upper sills on the s/b side, rework all the spacers within the hull so they have a uniform sweep, cut the top timbers on the s/b to length.  I then plan to sit down with the hull during our family vacation this summer in the mountains and go over it frame by frame.  I will spend my early mornings for those 10 days with scrapers, files, and steel wool.   I am looking forward to those quiet moments on the deck, sipping coffee and filing away - long before the kids get up!

 

Thanks for following along. 

 

Gary

Link to comment
Share on other sites

Link to comment
Share on other sites

  • 2 weeks later...

001.thumb.JPG.9ca706ea3db4484218a152f06704158c.JPG

Hi All,  About 575 hours into the voyage of Naiad.  I took this photo a while back, but never posted it.  Thought I would do so today so as to keep the thread alive.  These are the counter timbers and and various stern transoms.  One of the things I learned is that for temporary spacers, use pine or other soft wood as Ed recommends.  At various times, I used harder woods simply because of sizing.  This proved to be difficult when removing.  Just another of the many lessons learned.  Now I just have to try and not repeat my mistakes...  As discussed last week, I am at the point of final sanding of the hull.  Prior to that, I will plan on building up the stern so as to attain a nice fair sweep.  I am looking forward to this part since it is very detailed and somewhat complex.  All parts are book matched for uniformity.

 

These pieces are sitting on a cork lined tray that I made that clamps to the side of my build table with a thumb screw.

 

Thanks for following along.  G

Link to comment
Share on other sites

Looking great as usual, Gary.  Sorry, I have not been following very closely lately, but my chore workload is lightening up so my browsing level is increasing.  Those stern timbers look really good - and thanks for reinforcing the recommendation to use softwood for spacers.  Sometimes these useful ideas get submerged in the volume of text.

 

Ed

 

ps.  the term for the sweep of the deck is "sheer", as in "sheer of the deck", the same as used for the more pronounced curve of the external curve of the wales and planking.

Link to comment
Share on other sites

Incredible accuracy! Something I tried to aim for, but was not as pedantic as you are, so have a few minor alignment issues here and there :)

Please resist the temptation to lower the bar and make shortcuts. It is common to see people being super precise and detailed when making a keel and deadwood, and then speeding up when it's time for frames. You seem to keep the same precision from the beginning of the build!

Link to comment
Share on other sites

  • 2 weeks later...

Hi All,

 

Thanks all for the kind words and encouragement.  Ed - I have to say, the times I didn't follow your advice are the times I sorely regretted it...   Mike Y, you would be interested in the section of Ed's book around quality and setting a standard for your work.  He gives some great thoughts on the subject that I am trying to live by.  For instance - I will never drill a hole that I didn't first mark and pick.  I think its human nature to cut corners at some points.  I certainly have done that at times on this build and regret it.  I am striving to make each piece as perfect as possible.  But even then, there are challenges.  To make one's sword so sharp is to make it dull. 

 

Here are a few photos of the nearly completed hull.   I took these from the deck while on vacation in Northern California.  Yes, I took my ship on vacation and yes, the Admiral did tease me about it. 

 

Another tid bit - Don't be too anxious to remove the frame spacers or cross-spauls.  I spent more time repairing frames and adding new spacers.  I should have just left well enough alone.

 

Thanks for following along.  G

033.JPG

035.JPG

Link to comment
Share on other sites

Beautiful work, Gary, but that precarious pose on the rail is making me nervous.

 

I appreciate your words on the quality discussion in my book (books, actually) and I am glad if it has helped you.  Also, many of the ideas in the book came after I had gone astray and thought about how to avoid it.  And also, when you find a way to keep tools organized on the bench, I'd love to learn about it.  I feel like my tools and materials are pretty well organized whenn they are put away, but once work starts....

 

Ed

Link to comment
Share on other sites

  • 3 weeks later...
On ‎7‎/‎19‎/‎2017 at 4:08 PM, JosephHuntley said:

Loverly Work Gary about to start the Keel of mine at 1/48

 

love seeing others threads makes it easier to understand

Hi Joe, if you have the space for 1:48, I say go for it.  The plans have so much detail in them that you should be able to capture it nicely at that scale.  Looking forward to your build.  Reach out if you have questions.

 

Ed - as for perching the ship on the railing of that deck...  I got distracted and actually left it there for over an hour!  Wont do that one again!  It would have been a 20 foot drop to the woodpile below...

 

Thanks for all the kind words and follows!

 

G

Link to comment
Share on other sites

  • 7 months later...

Hi All,

 

Its been a solid 7-8 months since I have posted and almost a year and a half since I worked on Naiad.  Funny how these things go. 

 

590 hours into the voyage and I have successfully tackled the Stern Transom.  This was an extremely challenging area of the ship to model.  One of my greatest takeaways was that no matter how precise you are, you should always leave a little meat on the bone when it comes to making parts from patterns.  For some reason I cant help myself, I tend to cut the parts too close to the pattern lines. I have learned to love the scroll saw on a build like this and am amazed at how quickly my skills have developed with it.  That being said, leave atleast a 32nd of an inch or so of extra room on the parts.  Doing so will allow you some margin of error when fitting the puzzle together.

 

In addition to the Transom, I am doing a final detail of the lower hull. This includes inserting copper and iron bolts. I will also add the ribbands and other copper features.  One other lesson that I am trying to learn is - know when to stop sanding!  I have been sanding this hull off and on for two years.  There is only so much material to work with, so resist the temptation to make it to perfect to early.  I'm going to finish it and walk away.

 

Thanks for following along!

 

Gary

Installation of the brass bolts.jpg

Stern Transom assembly 1.jpg

Stern Transom assembly 2.jpg

Stern Transom from inside 3.jpg

Link to comment
Share on other sites

Below is a picture of my mom and me in front of my Naiad taken several years ago.  Sadly, my mom, Judith Milgram passed away several months ago.  She was a great lady and a great mother!  My mother was a professional artist and an inspiration for my modeling habits.  I owe her a great thanks for instilling in me a love of crafts and modeling (although, I never got her painting gene... that went to my sister…).  I will frame this photo and place it on my workbench.

 

Here are a few bricks she painted for me upon my request many years ago.   They sit on my desk at work.  When I was a child, we lived on the coast of Connecticut in a small beach house where my mother had painted the fireplace bricks with miniature sailing themes. Those were special times and a special place.  She is now buried in that town. I wonder if those scenes are still there in that house.

 

I also have dozens of her paintings hanging in my home and office, many of them with ocean or sailing themes.  I am very lucky to have them in my possession as well as to have had her as my mother. Thank you for allowing me to share this.

 

Gary

122 - Mom and Me with Naiad.JPG

IMG_0131.jpg

IMG_0132.jpg

IMG_0134.jpg

Link to comment
Share on other sites

Nice to have some nice keepsakes done by your mother. And all those fond memories. Cherish them.

 

Nice work on Naiad, too.

Ken

Started: MS Bounty Longboat,

On Hold:  Heinkel USS Choctaw paper

Down the road: Shipyard HMC Alert 1/96 paper, Mamoli Constitution Cross, MS USN Picket Boat #1

Scratchbuild: Echo Cross Section

 

Member Nautical Research Guild

Link to comment
Share on other sites

Thank you for the likes and nice comments. 

 

606 Hours into the build and I have completed the brass bolt installation on the hull.  I wish I did not use CA glue when installing the bolts.  The CA glue stains show through the wax and turpentine finish.  I should have tested this off the model!  This was not a problem when using oil based finishes on past ships.  Perhaps I need to add a little more turpentine to the mix?  Any ideas on how to solve this?

 

After the bolts were installed, I sanded the entire hull with 150 - 220 - 400 grit and then steel wool.  I focused on one frame at a time.  I then turned my attention to the ribbands. 

 

TIP: I used car pinstripping tape to layout the ribband sweep.  It worked out great!  I just ran the ribband in between the two stripes.  It even helped with glue drips. 

 

These pieces are about 30 scale feet long at six inches square.  I rounded them off slightly as Ed describes in his book.  They are boxwood and are hook scarfed for added detail.  An iron bolt will run through the ribband at the location of each frame. 

 

I absolutely love the clamps that Ed recommended be made for this model.  They are simple to make and very effective. Prior to putting any glue on the ribband I test fit the clamps and had them ready to go. I plan to do four ribbands on each side of the ship.  I don't intend on doing much planking.  I really want the structure to show.  There are a few trouble spots that will receive planking, just to hide the errors.

 

All has worked out well to this point. 

 

My plan is to finish the lower hull, just below the gun ports, before turning my attention back to the interior of the ship.

 

Thanks as always for following along.

 

Gary

IMG_0183.jpg

IMG_0182.jpg

Edited by GDM67
Link to comment
Share on other sites

Again, thank you for all the kind words and likes to my post about my Mom.  Today would have been her Birthday. 

 

610 Hours into the journey.  I think I am at the most fun part of the build yet!  The installation of the ribbands has proved to be very therapeutic and enjoyable. After the ribbands are installed, I can now beginning to apply finish to those sections that are complete.  I am using turpentine and wax as Ed recommends in his book.  You have to be incredibly diligent and disciplined on what you finish because it will literally be finished after that - no glue will stick...  That being said, after applying the wax and turpentine, I sand the spots over the brass bolts to remove the residual CA that I spoke of in my last post. 

 

I am very happy with the results.  The ribband installation is a slow process.  Each piece has to be test fit and many have to be steam bent before applying.

 

More next week.


Gary

IMG_0198.jpg

Link to comment
Share on other sites

  • 2 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...