Jump to content

Using bone as a modeling material - sources?


Recommended Posts

Hello, everyone...

 

Most of my time is spent repairing and restoring other people's models, mostly made in the past

by the client's family patriarch. Some are fine models, others are just sentimental junk. Currently,

I am tasked to clean and restore a bone model of an Inuit kayak from Western Greenland, which

I estimate is at least 100+ years old. It is carved from the solid, I am assuming from either Walrus,

Whale, or Elk bone, a few pieces are missing. Where or from what sources could I obtain a close

match in bone to replicate the missing parts?

Any ideas?

 

Thanks!!!

Eric Adams

Portland, Oregon 

Link to comment
Share on other sites

For elk, possibly try the local custom butcher shop who does game for the hunters.  

Mark
"The shipwright is slow, but the wood is patient." - me

Current Build:                                                                                             
Past Builds:
 La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD           Triton Cross-Section   

 NRG Hallf Hull Planking Kit                                                                            HMS Sphinx 1775 - Vanguard Models - 1:64               

 

Non-Ship Model:                                                                                         On hold, maybe forever:           

CH-53 Sikorsky - 1:48 - Revell - Completed                                                   Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)         

         

                                                                                                                                                                                                                                                                                                

Link to comment
Share on other sites

I had this problem but the pieces I had to replicate were only a 1/4". I found some bone decorative carvings at a jewelry supply house in New York City, they were intended for earrings or necklaces but they were perfect for me since they were clean and seasoned and I was able to cut what I needed out of them.

  

Quote

 

 Niagara USS Constitution 

 

Link to comment
Share on other sites

I just Googled, "how to prepare bone for carving"  and there was quite a bit.  There is also a lot under, "where to get bone for carving".

 

Bob

Every build is a learning experience.

 

Current build:  SS_ Mariefred

 

Completed builds:  US Coast Guard Pequot   Friendship-sloop,  Schooner Lettie-G.-Howard,   Spray,   Grand-Banks-dory

                                                a gaff rigged yawl,  HOGA (YT-146),  Int'l Dragon Class II,   Two Edwardian Launches 

 

In the Gallery:   Catboat,   International-Dragon-Class,   Spray

Link to comment
Share on other sites

  • 2 weeks later...

I am assuming from either Walrus,


Whale, or Elk bone, a few pieces are missing. Where or from what sources could I obtain a close match in bone to replicate the missing parts?"


 


 


Try and steer clear of real walrus or whalebone, they are seriously restricted 'ivory' materials in the US and possession of illegal ivory carries federal penalties.


 


I knew a scrimshaw carver on Cape Cod that went to jail for five years because he bought illegal whale ivory.


Link to comment
Share on other sites

When Modeler Bruce Hoof made his bone model he used the femurs from steers.  After boiling and prepping them the model ;looked great.

Dvid B

Link to comment
Share on other sites

Eric,

 

Here is a link to a Naval Ship modeling museum here in Canton Ohio. Larry Pulka is the ship builder and curator.  He builds scratch model masterpieces in bone.  He secures his material from local butcher shops. I am sure if you contacted him, he may be of some help to you.

 

By the way, if anyone is in the area, this is worth the trip.  His work is spectacular.

 

http://www.modelshipsbylarrypulka.com/index.html

Link to comment
Share on other sites

  • 2 weeks later...

Try going to your local pet store.  They all sell bovine large bones in a variety of sizes.  You can get "knuckles" or long bones, thoroughly sterilized and shrink wrapped.  They usually vary a bit in size.  You can pick your favorite shapes as needed and they are inexpensive.  They come in "regular" and "smoked."  The smoked are brown colored.  Get the plain regular white ones. (Your dog will love the smoked ones, but you don't want Rover chewing up your model!) Similarly avoid those that may have peanut butter or other tasty stuff stuffed inside of them.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...