Jump to content

H.M.S. Triton Cross Section by Sandman - 1:48


Recommended Posts

Hi All,

 

I am relatively new to model ship building and I am currently busy with a kit ship build. This hobby has really bitten me and I have been toying with the idea of starting a scratch build for a while now. I didn't want to start to large a project for now so when I saw the Triton cross section project, I immediately thought it would be perfect.

 

Seeing as I live in a country (Namibia) where wood is hard to come by and incredibly expensive the next step was to see what wood I could build it with. I found an old peach log and re-sawed it in order to use that. Although the wood is perfect I do not think I have enough for the entire project. I decided to use Kiaat which is a local wood and freely available here. It keeps an edge rather well and is very easy to work with. It also polishes to a rather nice finish. For the planking I plan to use Oak but I am still doing more research on that. I am open to any suggestions regarding that.

 

So the next step was to download the plans and get the saw dust flying. The rough lumber was cut into usable sizes using a band saw and the timber list as a rough guide. Next I cut the three pieces in the first plan and sanded them smooth. 

 

To make the rabbit, I formed a scraper from an old hack saw blade using my rotary tool and some needle files. A picture can be seen below:

 

post-3198-0-13376700-1390738815_thumb.jpg

 

Here I am busy forming the rabbit:

 

post-3198-0-35048200-1390738887_thumb.jpg

 

The three pieces are shown below. All in all I am happy with the result.

 

post-3198-0-22434000-1390738939_thumb.jpg

post-3198-0-80268800-1390738945_thumb.jpg

post-3198-0-82223700-1390739059_thumb.jpg

Link to comment
Share on other sites

Good start Sandman. Welcome to the Triton Cross Section Club :) 

Wish you good luck with your build. I'm the one of watcher for this build. 

 

Bugra.

There is nothing that a little sanding can't solve.. Bugra.

 

Current Builds : 

H.M.S. Triton Cross Section by Bugra - 1/48

Turkish Traditional Ship - Surmene Takasi by Bugra - 1:35

 

Link to comment
Share on other sites

Welcome on board, Have a lot of fun with your build

Regards Christian

 

Current build: HM Cutter Alert, 1777; HM Sloop Fly, 1776 - 1/36

On the drawing board: English Ship Sloops Fly, 1776, Comet, 1783 and Aetna, 1776; Naval Cutter Alert, 1777

Paused: HMS Triton, 1771 - 1/48

"Have no fear of perfection - you'll never reach it." Salvador Dali

Link to comment
Share on other sites

Hey Hendrik ; 

 

I saw your reply in Keel Drawing topic. Try to send a personal message to Chuck or Mark. It may escape from attention.

 

Bugra.

There is nothing that a little sanding can't solve.. Bugra.

 

Current Builds : 

H.M.S. Triton Cross Section by Bugra - 1/48

Turkish Traditional Ship - Surmene Takasi by Bugra - 1:35

 

Link to comment
Share on other sites

  • 2 weeks later...

Hello everyone

 

Just to keep everyone in the loop, I have heen very busy at work and home and thus have not been able to do much work on the x-section.

 

I have resawn the lumber that I will use for the frames and cut the pieces of the first frame. As soon as I have something respectable to post, I will do so.

 

I am doing research on how to do the cannons at the moment. I do not have a lathe so will probably end up casting them. I am considering pewter but have absolutely no idea how to do it so will still have to do some reading up.

 

Regards

Hendrik

Link to comment
Share on other sites

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...