MikeB4 Posted February 20, 2014 Share #1 Posted February 20, 2014 I've decided to put the Phantom down for awhile the final deciding factor was that during my move I some how lost the wire that was supplied with the kit.So while I'm trying to find some wire to replace the original I'm going to start this kit. this will be my first attempt at planking, this seems like a good beginners kit. I've also purchased the 18th Century Long Boat and the English Pinnace for future builds. I think I'll stick to building boats for awhile and learn how to plank on them before I take on a model ship. MarisStella.hr, jbford, Q A's Revenge and 1 other 4 Quote Phantom, first time build:MikeB4 English Pinnace by MikeB4 - Model Shipways - 1:24 18th Century Longboat by MikeB4 - FINISHED - Model Shipwa... Maine Peapod by MikeB4 - FINISHED - Midwest Products - 1:... Link to comment Share on other sites More sharing options...
jbford Posted February 20, 2014 Share #2 Posted February 20, 2014 i have one in the box ready to build. it will be very helpful to watch your progress, please post both sucesses and problem areas. MikeB4 1 Quote Link to comment Share on other sites More sharing options...
alde Posted February 20, 2014 Share #3 Posted February 20, 2014 Mike, That is a nice little kit. Be aware when you start to plank around the turn of the bilge that you will have to taper the planks on both ends. The instructions don't tell you this but it impossible to get the planks to lay against the forms if you don't. Just trim them so they lay against all the forms without stressing the wood. Al D. Quote The heart is happiest when the head and the hands work together. Al Current Builds: HMS Halifax 1/48 POF Lumberyard Kit Model Shipways Glad Tidings Acoustic Guitar Build FINISHED Link to comment Share on other sites More sharing options...
MikeB4 Posted February 20, 2014 Author Share #4 Posted February 20, 2014 Mike, That is a nice little kit. Be aware when you start to plank around the turn of the bilge that you will have to taper the planks on both ends. The instructions don't tell you this but it impossible to get the planks to lay against the forms if you don't. Just trim them so they lay against all the forms without stressing the wood. Al D. Thank you for the heads up. Quote Phantom, first time build:MikeB4 English Pinnace by MikeB4 - Model Shipways - 1:24 18th Century Longboat by MikeB4 - FINISHED - Model Shipwa... Maine Peapod by MikeB4 - FINISHED - Midwest Products - 1:... Link to comment Share on other sites More sharing options...
mrjuan Posted February 21, 2014 Share #5 Posted February 21, 2014 Hi Mike, I too have the Phantom currently shelved along with other more advanced kits like the MS Fair American and the 18th Century Longboat. My approach is to start off simple while building up my skill level. I have started out with the Midwest boats because I found them to be a great set of kits to learn from. In fact, I am close to completing the Maine Peapod and I have found it to be enjoyable to work with. As Alde has mentioned, the only tricky part is the planking around the bilge. But everything after that is straightforward. JB Quote Link to comment Share on other sites More sharing options...
MikeB4 Posted February 22, 2014 Author Share #6 Posted February 22, 2014 (edited) Hi Mike, I too have the Phantom currently shelved along with other more advanced kits like the MS Fair American and the 18th Century Longboat. My approach is to start off simple while building up my skill level. I have started out with the Midwest boats because I found them to be a great set of kits to learn from. In fact, I am close to completing the Maine Peapod and I have found it to be enjoyable to work with. As Alde has mentioned, the only tricky part is the planking around the bilge. But everything after that is straightforward. JB I wish I had known before purchasing the Phantom that it's really not a beginners kit at least not for those of us who have no real prior experience. although Model Expo claims it is a good first kit, I think it's quite deceptive of them to give you the impression that this kit is so easy even a caveman could do it.They leave out the fact that you have to figure out how to manufacture 80 percent of this kit on your own which requires some pretty advanced techniques. I use the word kit loosely it should be called a box filled with bass wood that has a picture of a boat on it. When I saw the Peapod Model I new this is a good beginner's kit,I wish I had found this one first. Edited February 22, 2014 by MikeB4 Quote Phantom, first time build:MikeB4 English Pinnace by MikeB4 - Model Shipways - 1:24 18th Century Longboat by MikeB4 - FINISHED - Model Shipwa... Maine Peapod by MikeB4 - FINISHED - Midwest Products - 1:... Link to comment Share on other sites More sharing options...
MikeB4 Posted February 26, 2014 Author Share #7 Posted February 26, 2014 I've checked the inventory, everything is there.Time to get started MarisStella.hr 1 Quote Phantom, first time build:MikeB4 English Pinnace by MikeB4 - Model Shipways - 1:24 18th Century Longboat by MikeB4 - FINISHED - Model Shipwa... Maine Peapod by MikeB4 - FINISHED - Midwest Products - 1:... Link to comment Share on other sites More sharing options...
alde Posted February 26, 2014 Share #8 Posted February 26, 2014 How do you guys keep your work area so neat and tidy? Estoy_Listo and omarcs 2 Quote The heart is happiest when the head and the hands work together. Al Current Builds: HMS Halifax 1/48 POF Lumberyard Kit Model Shipways Glad Tidings Acoustic Guitar Build FINISHED Link to comment Share on other sites More sharing options...
MikeB4 Posted March 12, 2014 Author Share #9 Posted March 12, 2014 I've got to this point But this is where it gets a little tricky . I tried tapering the ends of the plank but still finding it difficult to get the center to bend to the form. I'm going to try soaking the planks and pinning each one to the form. hopefully it will take the shape and dry that way. MarisStella.hr, hexnut and pete48 3 Quote Phantom, first time build:MikeB4 English Pinnace by MikeB4 - Model Shipways - 1:24 18th Century Longboat by MikeB4 - FINISHED - Model Shipwa... Maine Peapod by MikeB4 - FINISHED - Midwest Products - 1:... Link to comment Share on other sites More sharing options...
alde Posted March 12, 2014 Share #10 Posted March 12, 2014 Mike, They sure don't tell you any of this in the instructions. They need to be re-writen. This was the first planked hull that I tried and before I was a member on MSW and got frustrated with it. I didn't know anything about fitting and bending the planks. Soaking and pinning will go a long way to getting your planks right. You may also have to bevel the plank edges so the sit next to each other tight. Also, try a little amonia in the warm water when you soak the planks and give them a few hours to soak. MikeB4 1 Quote The heart is happiest when the head and the hands work together. Al Current Builds: HMS Halifax 1/48 POF Lumberyard Kit Model Shipways Glad Tidings Acoustic Guitar Build FINISHED Link to comment Share on other sites More sharing options...
AndyMech Posted March 12, 2014 Share #11 Posted March 12, 2014 I built Midwest's Peterboro Canoe, and this part of the construction looks similar. What worked wonders for me was beveling the lower edge of each new plank as you add it. I did it by hand, by sanding the plank on the thin edge at an angle and it made all the difference. It will especially important as you move over the curve toward the keel. One thing I had trouble with was conforming well enough to that curve to meet the keel properly - the planks really wanted to go higher than the keel. If you fight that battle early (keeping each plank on the bulkhead), it might be easier as your reach the keel. Good luck. Andy. alde and MikeB4 2 Quote Current Build: Model Shipways Pride of Baltimore II 1:64Completed build: Mamoli USS Constitution cross-section FINISHED 1:93 (2013 - 2014)Completed build: Revell USS Constitution FINISHED - PLASTIC 1:96 (2011-2013) Link to comment Share on other sites More sharing options...
MikeB4 Posted June 4, 2014 Author Share #12 Posted June 4, 2014 I finally got all the planking done. It was quite a learning experience for the first time doing it. MarisStella.hr, pete48 and hexnut 3 Quote Phantom, first time build:MikeB4 English Pinnace by MikeB4 - Model Shipways - 1:24 18th Century Longboat by MikeB4 - FINISHED - Model Shipwa... Maine Peapod by MikeB4 - FINISHED - Midwest Products - 1:... Link to comment Share on other sites More sharing options...
pete48 Posted June 4, 2014 Share #13 Posted June 4, 2014 Hello Mike , Thats Sweet the smaller boats are alot of fun to build . Looks like you are off to great start. The Hull looks good Best Regards, Pete MikeB4 1 Quote "may your sails be full of wind and the sun on your back" Current Builds : Future Builds : N.G Herreshoff 12 1/2 Scratch Build 3/4" = 1' - 0" Scale Completed Builds : Volvo 65 Farr Yacht Design Herreshoff Alerion Herreshoff Buzzards Bay 14 Volvo Open 70 Member : The Herreshoff Registry Montgomery Sailboat Owners Group Peter Kunst Sailboat Models http://www.herreshoffregistry.org/ http://www.msog.org/ http://www.facebook.com/Peter-Kunst-Sailboat-Models-1524464774524480/ Link to comment Share on other sites More sharing options...
TurkSailor Posted June 6, 2014 Share #14 Posted June 6, 2014 Hi Mike, I have this kit waiting for me, exciting to see someone experienced start the build! I'll have my chair pulled up! Following along. Cheers Eyup MikeB4 1 Quote Eyüp Current: Fifie - Amati Coca - Amati Completed: Felucca 1887 - Amati Link to comment Share on other sites More sharing options...
MikeB4 Posted June 13, 2014 Author Share #15 Posted June 13, 2014 Hi Mike, I have this kit waiting for me, exciting to see someone experienced start the build! I'll have my chair pulled up! Following along. Cheers Eyup I'm far from experienced, I'm learning the craft.It'll be interesting to see what the end result will look like. Quote Phantom, first time build:MikeB4 English Pinnace by MikeB4 - Model Shipways - 1:24 18th Century Longboat by MikeB4 - FINISHED - Model Shipwa... Maine Peapod by MikeB4 - FINISHED - Midwest Products - 1:... Link to comment Share on other sites More sharing options...
MikeB4 Posted June 15, 2014 Author Share #16 Posted June 15, 2014 I've installed the risers and the seats. pete48, Roger Carter and Aussie048 3 Quote Phantom, first time build:MikeB4 English Pinnace by MikeB4 - Model Shipways - 1:24 18th Century Longboat by MikeB4 - FINISHED - Model Shipwa... Maine Peapod by MikeB4 - FINISHED - Midwest Products - 1:... Link to comment Share on other sites More sharing options...
pete48 Posted June 15, 2014 Share #17 Posted June 15, 2014 Hello Mike, Nice work she is comming together nicely Best Regards, Pete Quote "may your sails be full of wind and the sun on your back" Current Builds : Future Builds : N.G Herreshoff 12 1/2 Scratch Build 3/4" = 1' - 0" Scale Completed Builds : Volvo 65 Farr Yacht Design Herreshoff Alerion Herreshoff Buzzards Bay 14 Volvo Open 70 Member : The Herreshoff Registry Montgomery Sailboat Owners Group Peter Kunst Sailboat Models http://www.herreshoffregistry.org/ http://www.msog.org/ http://www.facebook.com/Peter-Kunst-Sailboat-Models-1524464774524480/ Link to comment Share on other sites More sharing options...
MikeB4 Posted June 23, 2014 Author Share #18 Posted June 23, 2014 (edited) I've installed the rub rail. I'm going to paint a blue strip underneath the rail a 1/4" wide.This is a fun project, I'd recommend this kit to anyone new to the hobby. Edited June 23, 2014 by MikeB4 pete48, Littlebob, Aussie048 and 2 others 5 Quote Phantom, first time build:MikeB4 English Pinnace by MikeB4 - Model Shipways - 1:24 18th Century Longboat by MikeB4 - FINISHED - Model Shipwa... Maine Peapod by MikeB4 - FINISHED - Midwest Products - 1:... Link to comment Share on other sites More sharing options...
pete48 Posted June 24, 2014 Share #19 Posted June 24, 2014 Nice Job Mike, Looks like a fun build Best Regards, Pete MikeB4 1 Quote "may your sails be full of wind and the sun on your back" Current Builds : Future Builds : N.G Herreshoff 12 1/2 Scratch Build 3/4" = 1' - 0" Scale Completed Builds : Volvo 65 Farr Yacht Design Herreshoff Alerion Herreshoff Buzzards Bay 14 Volvo Open 70 Member : The Herreshoff Registry Montgomery Sailboat Owners Group Peter Kunst Sailboat Models http://www.herreshoffregistry.org/ http://www.msog.org/ http://www.facebook.com/Peter-Kunst-Sailboat-Models-1524464774524480/ Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.