Jump to content

Ed Mostowicz

Members
  • Content Count

    11
  • Joined

  • Last visited

Profile Information

  • Gender
    Not Telling
  • Location
    East Islip, NY

Recent Profile Visitors

120 profile views
  1. Ed Mostowicz

    Signal flags/pennants

    OK, that makes sense. I guess there's no harm in adding a shroud cleat. Thanks, Frankie. Ed.
  2. Ed Mostowicz

    Signal flags/pennants

    I'm just finishing Bluejacket's Smuggler kit. The plans sheets and the instruction book are very detailed and they presented no problem in the course of the build. However, there is no indication of where the halyards for the masthead pennants are to be belayed. Nothing about belay points in the manual and no callouts on the rigging plan. All of the belaying pins are in use for other running rigging. Any guidance would be appreciated. Ed.
  3. Z - Back in 1987 Model Shipways published a small book titled "Planking the Built-Up Ship Model" by Jim Roberts. It's very well illustrated and detailed and I highly recommend it. Model Expo has it http://modelexpo-online.com/planking-the-built-up-ship-model. If you decide to add a second layer of planking, I'd go with the thinnest material I could get or you'll end up with a hull that is too wide and out of scale. Ed.
  4. Ed Mostowicz

    Color of ratlines

    All good points. I've always used black line for my ratlines. The 'tar' they used was more of an oil that soaked into the rope fibers. It was also a very dark brown in color that usually looked black when viewed from a distance. So very dark brown or black would be my choice. BTW - I'm just starting the standing rigging on my model of Smuggler. Ed.
  5. I think that's safe to say. Unless you have specific information to the contrary, that is. Ed.
  6. I used to use at least 3 butt shift patterns, sometimes more. Then one of the older guys in the club, who used to work in a shipyard building fairly large schooners, said that they didn't use any pattern in planking a deck. They just took the longest length boards they had and installed them, just making sure that the butt joints weren't adjacent on the same deck beam. Since then, I use a scale plank length of about 24 feet - I read somewhere years ago that this was about the longest that a planking team could work with easily and safely. After the first plank is in, I shorten the next one by 4 or 5 feet and the next one 4 or 5 feet again. Then plank #4 is full length and so on from there. BTW, I work from the center out to the waterways. Ed.
  7. I'm not so sure about eyebolts; I haven't seen them on hoops. I think the lacing is just knotted around itself to tie it off.
  8. Ed Mostowicz

    Charles W. Morgan rigging

    Thank you as well, Frankie. I wasn't aware of Ashley's whaler book. I'll have to look for it. I was deciding to just go with the information that I have and hope for the best and your remarks make me feel better about that decision. I'm using standing rigging sizes for 300-400 ton ships in Underhill's Masting and Rigging the Clipper Ship and Ocean Carrier. It should be alright. Running rigging is some ways off and i'll work up something when I get there. Ed.
  9. Ed Mostowicz

    Charles W. Morgan rigging

    Thanks for the offer, mark, but I'm really looking for specific sizes. I have a unch of photos from a previous visit as well. They're geat for placement of gear, belaying points, deck arrangement, etc., but you can't really get rope sizing form them. Ed.
  10. Hello, all. New to MSW and the forums here. Looks like a great site from what I've read - okay lurked about - so far. I'm doing my 2nd rebuild of the old Marine Models kit of the Morgan. I rig my models with scale size line or as close to scale size as I can. I usually start with one of the references on my shelf - Lee's Masting and Rigging, Biddlecombe's masting and Rigging, Steel, Underhill, etc. - and work out the sizes of line required, but they all concern warships or merchants of an earlier era than the Morgan and certainly none of them mention whaling ships. I was wondering if anyone could direct me to a source for the sizes of rigging used on the ship. Or if I can use the merhant ship information in Underhill's Masting and Rigging the Clipper Ship and Ocean Carrier for instance. I contacted Mystic Seaport and they were no help; maybe I asked the wrong person. Regards, Ed.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to provide support to our members in their efforts to raise the quality of their model shipcraft.

The Nautical Research Guild puts on ship modeling seminars, yearly conferences, and juried competitions. We publish books on ship modeling techniques as well as our world-renowned quarterly magazine, The Nautical Research Journal, whose pages are full of articles by master ship modelers who show you how they build those exquisite details on their models, and by maritime historians who show you what details to build.

Our Emblem

Modelshipworld - Advancing Ship Modeling through Research
×