-
Posts
88 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Events
Everything posted by CaptCraig
-
Very nice! I like the work you have been doing. It is very clean and precise!
- 2,191 replies
-
- confederacy
- Model Shipways
-
(and 1 more)
Tagged with:
-
Congrats on the new purchase Jay! I am sure you will be whizzing out barrels and banisters in no time! I'll be watching for the videos!...lol
- 732 replies
-
- constitution
- model shipways
-
(and 1 more)
Tagged with:
-
Ok...time for a small update. I trimmed the bow to shape and added the other side of the hull. The bow actually came together pretty nicely! I would like to do some more this weekend. I think I will be able to get the first deck done hopefully. I still have to put the ribs inside of the hull. I have been busy tending to my wife's vehicle. Many repairs done this week so she can stay safe.
-
This part of the hull construction is a little challenging for the first time ship builder. But I think I am doing OK. I have used push pins and clamps to get the sides to twist properly. I cannot think of any other way to do this except one side at a time. Here is a side view of the hull: Here is the bow-end of the inner hull: Here is the stern end of the inner hull. I found it very annoying that they cut the stern so long. I had to remove a good 3/4 of an inch of material to get it to match the frame level as required by the instructions. I found this angle hard to match, but it looks pretty good for an amateur: Here is the bow. I may have to fill this a little after it dries, before I move forward with the other side. I think it is going fine. Everything seems to be lining up pretty well. Thanks to those of you who have taken the time to comment on my build. I really like the input!
-
Good day friends... I have started some work on the KoM build even though the shipyard is not quite complete. Today I cleaned the frame pieces and keel. I used a Dremel drum sanding attachment to just run quickly over the edges to remove the laser char: I was careful not to take too much material off of the edges. I then dry fitted the pieces into the keel and they all seemed to fit nice. Not too loose and not too tight. I used some 90 degree angle brackets to hold the frames into the keel so I can be fairly square when it dries: I was able to get all but two frames glued onto the keel. I started from the center and worked my way out. The two that I did not glue in will need to be done one at a time due to the lack of room in between them. This is what I have done so far: This is where I am at for now. I will finish putting the other two frame pieces in this week and I will start working the hull. I will update with more photos as I progress. Thanks for looking! Any remarks are welcome!
-
Impressive as always! My first build does not have a lot of rigging, but I know my next build will be more rigging intensive. You have great tips and I am sure everyone appreciates your work as much I do!
- 732 replies
-
- constitution
- model shipways
-
(and 1 more)
Tagged with:
-
The planking is superb to this point. I did not expect anything less as you are a true craftsman. Sorry you are not so good at picking football teams. Stick to the ship building! Lovely work Augie!
- 2,191 replies
-
- confederacy
- Model Shipways
-
(and 1 more)
Tagged with:
-
Well that decking looks great. It almost looks like natural wear. I think this is the effect you were trying to display. Excellent work Sjors!
- 1,616 replies
-
- caldercraft
- agamemnon
-
(and 1 more)
Tagged with:
-
Thanks Dragzz. I should be able to start some this weekend. I have to work on putting the lights up in the shipyard and I have a few papers to write for school as well. I have to figure out what I am going to use to square the frames in the hull while the glue dries. I do not want a whacked out hull when it is dry.
-
Another great video Jay! Thanks again for your lessons! I think these look good close up, so they must look good when viewing the ship overall.
- 732 replies
-
- constitution
- model shipways
-
(and 1 more)
Tagged with:
-
Well I am now home from work. I will no longer be traveling all week long, so I can get some things done. Tonight I took some more inventory. I am a little over half of the way through checking the items list. I have 2 1/3 pages out of 4 inventoried. It takes a while to go through the parts. I can't resist looking at the picture manual to see what I am taking inventory of. Some of it is a bit hard to picture by the description. I think I may need The Chopper for this build. there are many cuts to make and many of the same length. The Chopper would help to speed up this process.
-
Thanks for sharing this Jay. I enjoy all of your videos, so no need to for apologies!
- 732 replies
-
- constitution
- model shipways
-
(and 1 more)
Tagged with:
-
Dfellingham...You are correct Sir! Please provide us with another challenge!
-
Those coils actually look pretty realistic. Looking good!
- 732 replies
-
- constitution
- model shipways
-
(and 1 more)
Tagged with:
-
First Clue...This was not a fishing boat...
-
LOL...moving on...The rigging is looking great Jay! It is always a please to see your work.
- 732 replies
-
- constitution
- model shipways
-
(and 1 more)
Tagged with:
-
-
This is the USS Fairplay...Built in 1859 and served in the U.S. Navy until August 9, 1865.
About us
Modelshipworld - Advancing Ship Modeling through Research
SSL Secured
Your security is important for us so this Website is SSL-Secured
NRG Mailing Address
Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917
Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)
Helpful Links
About the NRG
If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.
The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.
The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.