Jump to content
MSW Spring Donation Drive

wallyh

Members
 View Profile  See their activity

  • Posts

    26

  • Joined

  • Last visited

Recent Profile Visitors

480 profile views
  1. wallyh
    Hi all, I'm about to start the second layer on my Fair American, I would like the planks to look scale. Can anyone point me to somewhere that talks about length and how they were staggered? Thanks again in advance, Wally
  2. wallyh
    I am planning to do a scratch build of the Rattlesnake using Harold Hahn's plans. My question is: can I use a 3/32" sheet plus a 1/8" sheet to make up the 7/32" thick frames? Thanks, Wally
  3. wallyh
    I have a question concerning reinforcing the joint on a keel on a kit such as the Rattlesnake. Is this needed? Or is everything OK after bulkheads are installed? Thanks in advance Wally
  4.    wallyh reacted to a post in a topic: Top-notch TurboCAD training videos - free.
  5.    Modeler12 reacted to a post in a topic: Cutting Board question
  6.    hornet reacted to a post in a topic: Cutting Board question
  7. wallyh
    I've used an Olfa gridded cutting mat for years (same one). It's 12"x18", never needed a bigger one,I just looked this one up at Jo-Anns (a sewing and craft shop). It's $22.99 but Jo-Anns almost always has a 40% off coupon to use. Wally
  8. wallyh
    I'm to the point in my Fair American build where I need some guidance on how to attach the spars to the mast. I've tried to find this on my own but I've come up empty handed. Is the spar simply glued or pinned to the mast ? Do you then "tie" this with rope? Any and all help will be appreciated. If I can be pointed to any instruction or pictures that would be good too. Wally
  9. wallyh
    I'm back again with another question. I've got the tree nails down to the right size I think, took them down to 25 on the draw plate and the number 71 drill bit seems right - thanks for that tip. My question - what do you use for cutting and finishing (sanding ?) the bamboo tree nails? Wally
  10. wallyh
    Well, back again, with all the help here I've managed to get a few pieces of bamboo down to 25 on the Byrnes drawplate. Next up up is a test on some planking, Would a size 75 drill be OK? Is there a depth for the treenails? Thanks again, Wally
  11. wallyh
    Thanks for all the help and ideas for my treenail "problem". I managed to do about 4' of BBQ skewer today, so far I've passed them through the number 55 hole on the drawplate - is this OK for the 1:48 scale? What size drill should I be using? As always, thanks so much - I can't tell you how much I've learned on this site. Wally
  12. wallyh
    Thanks to all for your replies. The scale of the ship is 1:48. And, I'm ashamed to say, I have a Byrnes drawplate that I can't seem to work! I was using bamboo skewers but not getting luck with drawing. I will try again this morning - what size should I be shooting for> Thanks again, Wally
  13. wallyh
    I'm just completing the deck planking on my Fair American and am wondering about tree nails. Should I add them? If so. I would appreciate any help that you could give me, ie, size of drill to use, etc. If this has already been answered perhaps you could point me to the right spot. Thanks, Wally
  14. wallyh
    Hi Everyone. When I built my bench (2'W x 5'L x 37" H) I put heavy duty casters on it. When needed I roll the bench out into the garage (normally it's against a wall), set the locks on the casters and then I can easily walk around the bench. I use a drafting stool with this bench and a mechanic's hydraulic roll around seat. Wally
  15. wallyh
    Thanks for the replies. Russ - I was planning to use the Buff color on the bulwarks. Should I be considering other colors? Tom - thanks on the heads up on the RR colors. Wally
  16. wallyh
    Hi Everyone, I would like to use the color buff on my Fair American but I'm not sure exactly what shade this is - looks like it varies all over a range between a tan and a yellow color. Can anyone point me to the proper color? Thanks, Wally
  17. wallyh
    Hi, I am following your build and loving it! There's some good information on the Model Expo site. The model US Brig Syren has wonderful documentation (by Chuck Passaro). Under Documentation for the model Syren, Chapter 11 has some great info on cannons and blocks. Wally
  18. wallyh
    Thanks so much Nathan, I haven't done anything yet! You're right, it does look good and seems to me that this would be the way to go. I'm pretty sure you wouldn't bend down to go through that short door on the real ship. Wally

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)

Helpful Links

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem ®

Modelshipworld - Advancing Ship Modeling through Research

Nautical Research Guild ® and the NRG logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,999,236 & No. 6,999,237, registered March 14, 2023)

×
×
  • Create New...