Search the Community
Showing results for tags 'pof'.
-
Well team, I hope I haven't bitten off more that I can chew but I have taken over a full frame model of the EURYALUS in 1:48 scale from a long standing member of this forum; Russell H. Russell unfortunately is not in a position to continue building this model so he has offered it to me to complete. Russell has already achieved full framing from stem to the fashion pieces and the fitting of transoms and the Stersom Knee. He has also made a start on fairing inside and out and started laying the first few rows of the ceiling from the keelson. Port side is full frame, Starboard mostly framed; gaps for viewing internally. The plan is to fully plank Port side and only partially plank Starboard side (same for the decks. Russell hasn't worked on the model for nearly 2 years so things have settle a little. First step will be to ensure full frame alignment and secured them before continuing the journey. A little damage has occurred with one Of course this will mean that THUNDERER will be put on the back burner as I will not have the space to build two 1:48 warships concurrently. Time to check out the other EURYALUS builds on the forum.....
- 97 replies
-
- euryalus
- 1:48 scale
-
(and 1 more)
Tagged with:
-
Hi, This is a validation model for kit development, and the work of hull part will begin soon. About 70% of the design has been completed. My partners will make 1:36, 1:48 and bow section respectively. All the photos from their buildlog are authorized for me to release in MSW. This project started from NMM's original draught, True Image Model, a ship model studio from UK, which obtained a commercial kit license from NMM. Now there are three modelers involved in the model validation. We will complete the bow section kit first, because it is relatively simple. The wood used in kit is boxwood / pear wood. Welcome to pay attention to our follow-up progress. Jack
-
Being dissatisfied with the bow framing of frames 2 thru 12, these frames were completely reconstructed using my forecastle template previously submitted in the forum. The results were satisfactory as these photos show. I also prefabricated timber heads which procedure will be posted in a day or two. This exercise set me back almost 2 months. I would like to mention 3 of the frames needed build out at various locations. I laminated 1.5" (s) strips to the frames at these low locations. Results were fine.
-
La Renommee - 30 guns - 26 x 8 lb on the main deck - 4 x 4 lb on the quarter deck. 125.75' x 33.75' x 17' Imperial The plans are those of the ANCRE monograph by Jean Boudriot 1993. The monograph includes the lofted shape of each of the 58 bends. This part of the monograph is not needed for my purposes. I will not be using these individual frame plans. I am using a new method. All of the frames between each station are worked as a single unit. For this hull, I have chosen to build it as a solid wall of framing timbers. I usually frame true POF, with spaces. The spaces are temporarily filled for the shaping and fairing of the frames. The space filling wood is bonded using an easily reversible agent. The unit handles as thought it was a single piece of wood and is not at all fragile. The edges of the frames are protected from being rounded. For La Renommee I will PVA bond all of the frame timbers. The lofting required has some similarities with POB level of lofting, but more work is required. In all, the time required to develop a set of frame timber patterns for La Renommee was about 5 days. This is a much shorter time than it takes to loft each frame by plotting it using a drawing board or CAD. My shortest lofting time was 4 days - for the early clipper Rainbow. In general it takes about 10 days. A multi deck warship takes longer. My reading and experience points to this method as being analogous to the way actual ships were framed prior to 1860. The product of the mold loft was likely just molds for the midline shape of the bends at the station positions. Ribbands and experience of the ship wrights would have been used to shape the timbers between. Chocks would be used where I place filling wood. These would not have been removed later. Because the wood for the model is 60 times lighter and 60 times smaller, I can shape all of these frames as a unit. It also allows the wood to be taken to the cutting edge and easily manipulated, as the opposite was necessary for the ship. A Glossary for the terms that I will use: This whole group is a Bend. It is two Frames. Each of the parts is a Timber.
- 26 replies
-
Hi Everyone, Yes another new chap here to the forum. I have been lurking in the shadows for sometime reading. reading and researching as I am new to scratch building wooden ship models. I am however an avid RC aircraft modeler and build and fly only scale gliders from 1/4 scale up. The largest scratch built glider I have has a wingspan of 7.5m so no small foamies here. Whilst this build goes on I also purchased the Hayling Hoy book from sea-watch and will be building this during the Triton build. A little test bed really. I hope to document this Triton build to a high level to ensure I have a beautiful replica once completed and I am certain I will have plenty of questions along the way so the more detail provided the easier it will be to gain assistance. There isn't a whole lot to show just yet as I have only printed out a very small number of the large format drawings and have a ton to go until I finish printing them all. I was thinking about not printing everything at once to save up a little space but I think it will be a lot easier to print them all out then check off each sheet with the master list to ensure I don't miss anything. That's really all there is for now, I needed to get the build log started as it will give me the little nudge along to get things moving along nicely. I would like to thank all the guys and gals out there that contributed to these drawings, they are very thorough and would have taken hundreds of man hours to put together so thank you all, especially at only 5 bucks, brilliant. Anyway I better try to get some sleep its 3am here. Chow for now. Steve
-
I'm midway through a build of the Emma C. Berry. I took a year+ off due to buying and renovating a new house. In the meantime, people have been anxiously awaiting promised updates of progress. I thought a fun project, or couple, would be to recreate some of the parts of some amazing builds on MSW. A recreated frame w/ blackened nails or a full keel. Accompanied by some plans and shadowboxed. I'm struggling on two parts: I can't seem to get wood to save my life. I have placed an order at Wood Project Source, but two weeks later realized I neglected to supply a unit number in my shipping address (please note, this is an error on my end - not theirs). Reading before placing a second order, due to demand, it may be 2-3+ weeks before I can get some wood to work with. Any US vendors than can delivery relatively quicker? Looking for pear and boxwood preferably. I don't have accurate plans for a frame (and it's parts) or keel. Are there accessible plans with a minimal cost that are limited to the parts I want? I know this question extends beyond the scope of this forum, but advise would be great. Thank you all, and a silent tip of the hat to all the builds I've been watching that have inspired me. Ryan
-
Hello all... Is there a true and legit Plank on Frame kit available in the market? Preferably a large ship like a 3 masted square rigged ship. Not plans, but the whole kit. Thanks in advance Ulises
About us
Modelshipworld - Advancing Ship Modeling through Research
SSL Secured
Your security is important for us so this Website is SSL-Secured
NRG Mailing Address
Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917
Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)
Helpful Links
About the NRG
If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.
The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.
The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.