Search the Community
Showing results for tags 'ratlines'.
Found 6 results
-
Ratline Video's I have added two video to YouTube showing me adding some ratlines to the foremast shroud. I did record two videos, each taken from a different view point, in an attempt to keep the back of hands obscuring the view, but it was not always possible. Links to the two videos: Ratline Video 1 Ratline Video 2 As a general rule the I cut a length of thread that is approx. twice the width of the shroud for the ratline. The thread is then pulled through a block of beeswax a few times. I then use a hairdryer on the thread which helps the beeswax to flow. As each clove hitch knot is created I check the position with the template. Once I am happy I brush on some diluted wood glue to the knot and ratline
-
- 6
-
-
-
- Ratlines
- adding ratlines
- (and 2 more)
-
Hi all, I'm in the middle of building the Revell Cutty Sark. Have had the kit stored for about 15 years so thought it was about time to take it out of the box. Basic hull and mast construction is complete and though the colour scheme may not be true to life, many ships changed parts of their colour scheme during their service so I make no apologies. One of the worst aspects of the model is the amount of flash and the filing that has to be done to remove excess material - very time consuming. However, it's not too much of a problem to get the parts to fit. This brings me on to sequencing and here I think the instructions could be improved. For instance, I would do as much rigging work as possible before attaching the spars to the masts. Most of the Standing Rigging is in place including the Ratlines, a lot easier to do than working your way over and under the spars. Incidentally, the ratlines are all hand knotted and the way I did them, setting them up on a frame, prevents the "hourglass" shape which some folk have mentioned. You can see this in the pictures; I've used the template supplied with the model and stretched the vertical threads using map pins to hold in place. Then again using map pins to hold it in place, I start the horizontal threads with the tension maintained. This way, you can complete the ratlines for one side of the model just by working across the template, then repeat for the second side. I'm just about to start the sails and running rigging and would appreciate advice on whether to glue the yards to the masts and then attach the sails, blocks, etc.. Or attach the sails, blocks, and so on to the yards first, and then mount the sub-assembly to the mast. I reckon it would also be sensible to work from the deck upwards rather than top downwards. Any ideas welcome guys, thanks.
-
I have a question about the shrouds on the top gallant masts. I noticed there are 3 shroud lines but no ratlines. If one were to lower the royal yard how do you get to it if need be? I would have thought ratlines would solve the problem but there are none shown on the plans. Understand I don’t want to tie more ratlines but it does not make sense to me. 🤔. Below is a pic of the standing rigging for the main top gallant mast. The same is shown for the fore and Mizzen masts. Any insight would be helpful. In the meantime I will look again in my limited library for any answers. Tom
-
I've reached the point on my Scottish Maid that I need to rig the ratlines. I remember reading a method here on Model Ship World that involved using graph paper to make a template to keep them properly spaced. Before posing, I searched for those posts and couldn't find them. Anyone recall that method? It made all kinds of sense when I read it, but I need a refresher to actually do it. Thanks! Dan
-
Anyone see the new Ratline tool by MS. Any experience?
-
I'm struggling with a rigging question for my current built, the Corel Ranger, which is a fictional version of a US Revenue Schooner from around 1820. The plans for the standing rigging show only one normal shroud per mast (per side), with no allowance for ratlines. Then it shows two other lines from the top of the mast, through the crosstrees, down to blocks along the rail and deck, which appear to serve as shrouds but are not listed as such and don't use deadeyes or blackened lines. My confusion is twofold: One, what are these other lines for, as they don't appear to be operational (don't attach to any sails, yards, gaffs, etc) but aren't treated as standing rigging either. Two, with only one shroud per mast and no ratlines, how would sailors reach the crosstrees and the upper yards/gaffs for handling the topsails and any other repairs? One respondent in my build log suggested a bosun's chair, which might make sense for occasional access, but the crew would have to get up there quickly and commonly in normal sailing operations. Below is my attempt to diagram the situation. Most of the contemporary images I can find show these schooners with two or three shrouds per mast (per side) with ratlines, as I would expect. So is the kit just full of guano when it comes to this rigging plan, or is there a reason to do it this way? I would greatly appreciate any advice.
Our Emblem ®
