Search the Community
Showing results for tags 'waterline'.
Found 3 results
-
Waterline Marker Hobbyzone Catalogue # HZ-PW Available from Hobbyzonefor 25.00zł (£5.21 as of 6/6/2018) If you’re new to the hobby and setting up a list of essentials for purchase, or if you need to replace your current waterline marker for some reason, then Hobbyzone has a pretty inexpensive way of doing this. In case you’ve never heard of Hobbyzone, they are a Polish company who produce some excellent workshop workbench modules to store your tools and other items, all with magnets which lock the individual units together. This range is totally flexible and can grow as your own needs must. Maybe you have heard of Hobbyzone but didn’t realise that they now have a set of products aimed specifically at our hobby? For our first look at this range of tools, I thought the waterline marker was a good introduction. Hobbyzone products tend to be made from MDF parts, which are CNC routed to very fine tolerances, which fit superbly. I can say this because I have been a customer of them for about 3yrs now. The waterline marker is packed into a clear plastic sleeve wrap with a couple of product labels. Opening the packet, you’ll note that all MDF parts are held together with elastic bands. A packet of hardware is included, as is a single instruction sheet. No tools re needed for this except for clamps. Clean-up of parts isn’t necessary. A quick test fit of parts shows that everything does indeed fit snugly, with just a little playfor the glue joints. For glue, I use Titebond III which has a relatively quick grab time and sets with an amazingly strong joint. I first glue the two upright parts together and leave for 15 minutes before then gluing this assembly to the base. Any excess glue is removed with the corner of a steel rule. One of those upright parts has a channel milled into it for the pencil unit to slide along. Assembling the pencil holder is very simple indeed. Two MDF parts are supplied, and one of these has a V-channel machined into it for holding the pencil, and holes for the bolts. The other part has those holes, but the exterior is machined to accommodate the hex head of the bolts. The bolts are first slotted into this piece and the v-slot dropped into position. The two parts are now fitted to the slot on the upright assembly and the washers and wingnuts used to secure. Before tightening, a pencil is added to the unit, and the wingnuts tightened evenly. It’s a good idea to use a short pencil for this as you want to keep the waterline parker relatively close to your boat/ship so that there’s no flexing of the pencil. That’s it! This tool can be adjusted for heights between 45mm and 225mm, so certainly big enough for most applications. Another real bonus here is the price. At just over a Fiver sterling, then this can’t be beat! My sincere thanks to Hobbyzone for kindly sending out this item for review here on MSW. Hobbyzone products can be bought directly or through one of their global distributors. Tell them you saw this review on Model Ship World
-
Bluejacket is proud to announce an exciting new kit, the Ellie Mara, a 2-masted coastal schooner typical of the mid-1800's. With a wide beam and shallow draft, she could get very close to the shore. The kit has a cast resin hull, laser cut pieces, Britannia fittings, brass rod, and 4 sizes and colors of rigging thread. overall length is 15", and is scaled for HO (1:87) She has a very attractive list price of $124.00, part number K1115.
-
Dear friends of the light balsawood, As I have found plans for the small Imperial Russian Navy's gunboat and the need of a chrismas present I decided to start the 1/144 bread & butter project of STERLYAD launched in 1854. I scaled down the Russian plans - and saved a 1/72 version as well - to built a little non-prominent-ship model. Both scales layed side by side to compare. And as my brother served on a minelayer I decided to try a ship as a present. The „Big Vicky of Portmouth“ isn't non-prominent... and too timeconsuming - so I looked for something smaller and ended at a Russian cruiser's launch (too small) and this gun boat that fits my limitations (depends on the display case). I decided to reuse a quickbuilding scale and method I used years ago for my Battlefleet 1900 wargaming ships (in the more workflowbreaking and fuzzy 1/780). Here all what is in use of the twosided planset: So I scaled down the plan from Sukolov - I additivly ordered the planset for the 30 amnd 64 pounder ordonances. But I have to admit the ordonance plans are - politly spoken - semi-scale. The gunboat's plans are rude in sence of detailing (there are missing any cuts or details without of anchors and some rigging detail) i have to admit. The copies I cut off and glued on the 6mm balsa wood. Taking as much model hull from a single plank as possible. Then I extracted the „superstructure“ and that's all what happend till today. Here comparing of the hights of the superstructure to the drawing: Besides a testfit on a 10mm balsa plank in between the two Ikea frames nothing important happens: Hope you don't dislike my patientfree hurrying little gunboat project too much within your detail crowned 74 and 100 gun ships, HMYs and other slowgrowing projects I like to read in so much and with gerat respect.
Our Emblem ®
