Jump to content
Mahuna

Dunbrody Irish Famine Ship by Mahuna - 1:48 Sectional Model

Recommended Posts

Part 1 - Introduction

 

When I first started ship modeling in 2012, I purchased a set of plans from Seaways Publishing for the Dunbrody Irish Famine Ship.  The plans appealed to me because I was born in Ireland and have read quite a bit on the famine years. 

 

The Dunbrody is a replica of an actual ship that was built in Quebec in 1845 by Thomas Hamilton Oliver for William Graves, a lumber merchant from New Ross in County Wexford in the southeastern part of Ireland.  The Dunbrody’s construction coincided with the Irish Famine years, during which the Irish tenant farmers were starving due to the failure of their potato crops – their primary food source.  The ship was designed to carry lumber from the new world to Ireland and England.  On her return voyage she mainly carried pig iron and limestone, which left room for carrying a fairly large number of passengers and normally accommodated up to 176 Irish emigrants who were trying to escape the potato famine.

 

The replica ship was commissioned by the John F. Kennedy Trust of New Ross, as a tribute to the emigration of the Kennedy family from their Irish homestead near New Ross.  The current Dunbrody was designed by the naval architect Colin Mudie, who had designed a number of replica ships.  The plans for the replica were based on entries for the original ship in the Lloyd’s Register, and from certificates and surveys.

 

                      post-331-0-67419300-1459136242.jpg

 

Mr. Mudie also wrote a book titled “Sailing Ships” in which he presented a number of ships he had designed.  The book included a section on the design and construction of the Dunbrody.

 

I don’t think I had any real thoughts on how to model the Dunbrody when I originally purchased the plans.  I was new to modeling and didn’t have any experience in scratch building.  After seeing Ed Tosti’s work on Young America I decided a few things. 

 

First, Dunbrody is not a very refined ship, and her lines are no comparison to the beauty of the clipper ships.  My primary reason for building Dunbrody is to show the accommodations for the Irish emigrants.  I felt that this could best be accomplished by building a sectional model.

 

The plans from Seaways Publishing contain most, if not all, of the details needed to construct an accurate model, so I would try to reproduce the details presented in the plans.

 

           post-331-0-15572100-1459136270.jpg

 

I would use Ed Tosti’s build logs and books for Naiad and Young America to learn the techniques and processes I would need to build the model. 

 

In addition to the plans for Dunbrody, and Ed’s books, I will also be using two excellent books as references: “American Built Packets and Freighters of the 1850s” by William L. Crothers and “Wooden Ship-Building” by Charles Desmond.

 

A number of questions arose as I started planning for this build, and I started a thread entitled “Planning for a Sectional Model of Dunbrody” to get some feedback from the more experienced modelers on this site.  Most of my questions have been resolved, so it’s a good time to start building.

Share this post


Link to post
Share on other sites

Part 2 – The Sectional Model

 

My interest in the model is to show the portion of the ship that was occupied by the Irish emigrants.  The Accommodation Deck consisted of three main sections:  the aft section contained the quarters for the ship’s officers and first class passengers, and the forward section was the quarters for the ship’s crew.  Temporary quarters for the emigrants were set up in the central area of the ship.  The following illustration from Colin Mudie’s book depicts the general layout of the Accomodation Deck.  His comments are interesting, in that he suspects the ship was designed from the beginning to support the emigrant trade.

 

                       post-331-0-07739800-1459136537_thumb.jpg

 

The sectional model will encompass the central area of the ship, from frame 19 to frame 44, a distance of 48 feet.  This area is the middle of the emigrant area.  The scale will be 1:48, so the model will be 12 inches long.

 

The starboard side of the model will be completely built, but the port side will be left as open as possible so that the interior of the ship showing the emigrants living conditions can be seen.  On a trip to Ireland in 2013 I toured the Dunbrody, and was taken by the cramped quarters the emigrants shared during the voyage.

 

Structural timbers will be made from Madrone, a hardwood from the Pacific Northwest that is very similar to Pear in that it is relatively dense, has a very tight grain, and is a light pinkish-brown color.  Madrone machines very cleanly, and finishes well.  Madrone is sometimes difficult to find, but is much less costly that European pear woods.  Planking, deck furniture, and other non-structural parts will be made from Castello, which has many of the same properties and color as Boxwood. 

 

I haven’t decided yet whether the model will be presented on a simple base or whether I will build a model of the building slip for the ship.  I am also considering using some figures of emigrants in the ship, but this depends on being able to find 1:48 figures that can be used with some minor modifications.

 

 

Share this post


Link to post
Share on other sites

Frank,

 

Its good to see you getting off the ground with the model.  I look forward to following your progress on this interesting and unique project.

 

Ed

Share this post


Link to post
Share on other sites

Hi Frank

 

This looks interesting, not to mention challenging. I also like the fact that there's some connection to your past, which makes the build all the more meaningful.

 

I'm on board!

 

Cheers

 

Patrick

Share this post


Link to post
Share on other sites

Frank,

 

The Cobh Heritage Center

 

http://www.cobhheritage.com/

 

has a mock-up of the emigrant quarters on a "coffin ship" that may be of use if you can get historically accurate details from them or at least photos of their exhibit for the furnishings, dress, etc.

 

Richard (that's my Irish bride in the photo)

Share this post


Link to post
Share on other sites

Part 3 – The Model Shipway

 

Before beginning construction on the model, I needed to build the platform to support the ship during construction – the Model Shipway.

 

I used a 12x24 melamine shelf for the building board, mounted some 5/8x5/8 rails under it, and added felt feet to save the surfaces it would be on.  A centerline was scribed down the center of the Shipway.

 

            post-331-0-92397100-1459218050_thumb.jpg

 

This shelf is only 21/32 thick, so it is not thick enough to support the normal ½” T-track.  I was able to find shallow T-Track (3/8”) from Lee Valley, along with T-Nuts specifically configured for these tracks.

 

            post-331-0-65306800-1459218087_thumb.jpg

 

            post-331-0-38142700-1459218107_thumb.jpg

 

A scaled drawing of the frame configuration of the sectional model was needed for the Shipway.  I developed this using TurboCad Designer (a 2D CAD program).

 

             post-331-0-84198000-1459218141_thumb.jpg

 

There will be 52 frames in the sectional model, arranged in frame pairs or framesets.  The 26 framesets of the sectional model are represented by the different color lines.  The green line is the forward face of the forward frame of a frameset.  The red line is the aft face of the aft frame of a frameset.  The black line is the junction of the two frames, or the middle of the frameset.

 

It can be seen that the frames are very close to each other – not the usual ‘room and space’ that we would normally expect.  The sided dimension of the floor of each frame in a frameset is 8.5 inches, making the frameset 17 inches at the floors.  The space between frames is only 5+ inches, or 0.11 inches at 1:48 scale.

 

The drawing of the frame configuration was printed on 11x17 card stock (I found 100 lb card stock that my printer was able to handle).  After it was trimmed to the appropriate size, 9x15.5, I aligned the centerline of the drawing with the centerline of the Shipway, then glued it to the Shipway using Krylon 7010 spray adhesive. I coated the drawing with Krylon Preserve-it to protect the drawing (I learned of these products from Ed’s Young America book, and they’re excellent).

 

I constructed two types of fixtures for the Shipway, as shown in the following photo (the keel is already installed in this photo, but more on that in a later post)

 

            post-331-0-93208100-1459218176_thumb.jpg

 

The fixture in the middle of the Shipway will be used to align the individual frameset during installation, and will also serve as a clamping base to secure the frameset while the glue is curing.

 

The gantry-like fixtures at each end will be used to hold a string stretched between them as an aid in centering the frameset.  These strings are laid in notches in the cross-piece and have been centered over the centerline of the drawing.  The centering string and its weights can be seen in this view of the Shipway.

 

            post-331-0-03933500-1459218212_thumb.jpg

 

The next post will address making the keel and mounting it to the Shipway.

Share this post


Link to post
Share on other sites

Hi Frank

 

That's a pretty speccie Model Shipway that you've got there. It certainly looks like it's fit for the job.

 

I'm sure It won't be long before we can see the 52 frames all assembled on the board.

 

All the best and happy modelling!

 

Cheers

 

Patrick

Share this post


Link to post
Share on other sites

Aha!  A genuine start.  I'll be watching with interest.

 

John

 

Welcome John 

 

 

Hi Frank

 

That's a pretty speccie Model Shipway that you've got there. It certainly looks like it's fit for the job.

 

I'm sure It won't be long before we can see the 52 frames all assembled on the board.

 

All the best and happy modelling!

 

Cheers

 

Patrick

 

Hi Patrick

 

Depends on your definition of 'long' - one step at a time.

Share this post


Link to post
Share on other sites

I'll be following along as well - my great-grandparents on both sides of the family emigrated to America from Ireland during the time of the Famine - not sure what type of ship transported them here.. This will be an interesting build to follow.

Share this post


Link to post
Share on other sites

Part 4 – The Keel Assembly

 

Dunbrody’s Keel, as measured from the construction plan, is 14 inches square.  There is a rabbet that starts approximately 5 inches down from the top of the keel.  Below the keel is what the plans call a False Keel, which has a breadth of 14 inches and a depth of 9 inches.

 

My reading of the Crothers and Desmond books shows that typically a False Keel is installed to protect the keel from damage due to grounding or striking an obstacle, and as such is relatively thin at 1 – 4 inches, is installed in a fashion that would allow it to be easily replaced, and has only simple butts to join its components.  The depth of Dunbrody’s False Keel seems to be much larger than expected, and the construction plan shows the parts of the false keel joined by a nibbed scarf joint. 

 

I’ve found several items in Dunbrody’s construction that are very different than the construction described in the Crothers and Desmond books.  I’ll point these out as I go along, but my intent is to reproduce the Dunbrody plan as far as possible.

 

The keel at 1:48 would be .292 inches, or a little over 18.5 64ths.  To simplify the model construction, I’ve reduced this to 9/32.  After milling some appropriate lumber I needed to mark a centerline on the keel and found this to be fairly difficult with a pencil and ruler.  I had seen a woodworker’s centering device that consisted of two outside rods with a pencil in the middle, all equidistant from each other.  I made a miniature of this using stiff piano wire as the outside rods and a medium needle as the marking device instead of a pencil.  Drilling the holes at the correct distances was fairly easy using the calibrated wheels of the milling machine.

 

                        post-331-0-69899100-1459311603_thumb.jpg

 

I also needed a way to cut the rabbet.  Since the sectional model is the middle of the ship the keel is straight and flat, so the rabbet will be the same throughout the model.  I decided to use a scraper type of device similar to what Ed shows in Young America.  I drafted the profile of the rabbet in TurboCad.

 

                        post-331-0-87427200-1459311623_thumb.jpg

 

I then pasted this profile onto a piece of 18 gauge stainless sheet and cut the shape of the rabbet cutting tool using a jewelers saw and files.

 

                        post-331-0-89018200-1459311660_thumb.jpg

 

Before cutting the rabbet, though, I needed to create a hooked scarf joint in the keel.  I drafted the pattern for the hooked scarf and used a glue stick to paste it to the wood to be cut.

 

                        post-331-0-97006700-1459311690_thumb.jpg

 

This being my first hooked scarf, there was a lot of trial and error, and the scrap box started filling up.  As part of making the joint, I needed to set up a clamping arrangement that would ensure the two pieces of the keel stayed straight and level while being glued.  I used a straight piece of aluminum stock as a straight edge, and clamped this to a piece of ¼ “ plate glass as a flat base.  I then used an arrangement of clamps that would keep the keel tight against the straightedge and the glass surface, making sure that the joint itself was properly clamped.

 

                        post-331-0-24973300-1459311721_thumb.jpg

 

The nibbed scarf of the False Keel can be seen in the background, awaiting gluing.  I decided to work on the nibbed scarf of the False Keel at the same time as the Keel’s hooked scarf.  The following photo shows the end result for both joints.

 

                        post-331-0-28178300-1459311745_thumb.jpg

 

When I was reasonably happy with the joint on the keel I fastened the joint using the bolt pattern described in the reference books and then cut the rabbet.

 

                        post-331-0-69828000-1459311771_thumb.jpg

 

In prior builds I’ve always neglected to address mounting requirements until the end of construction, and then have run into difficulties getting a mount that is secure and attractive.  I decided on this build to use the approach from both Naiad and Young America, which is to use mounting bolts that attach to nuts that are embedded in the False Keel and then covered by the Keel.

 

The size of the False Keel limited my choice of threading, so I used 4-40 nuts.  Even this nut size was too large to comfortably embed in the false Keel, so I filed the nuts square to reduce their size and to simplify the cutting required for them.  The following photo shows an original 4-40 nut and the two that were reduced to square.

 

                        post-331-0-38363700-1459311806_thumb.jpg

 

Since the mounting bolt needed a shoulder to prevent it from being run too far into the False Keel, I decided to center drill a ¼-20 threaded rod, and to solder an appropriate length of 4-40 threaded rod in the hole.

 

                        post-331-0-30981200-1459311845_thumb.jpg

 

This is satisfactory at present, but I think I’ll replace the bolt with a one-piece bolt with two different thread sizes, as in Ed’s work.  The false Keel was then mounted on the shipway.

 

                        post-331-0-65903100-1459311871_thumb.jpg

 

                        post-331-0-52816900-1459311951_thumb.jpg

 

This was followed by gluing the Keel to the False Keel, effectively hiding the mounting hardware.  I used spring clamps to ensure that the Keel and false Keel were properly aligned, and pins to secure the joint from the top.

 

                        post-331-0-88069400-1459311988_thumb.jpg

 

This completed the installation of the Keel Assembly.

 

                        post-331-0-85507200-1459312021_thumb.jpg

 

In the next post we’ll start discussing the construction of Dunbrody’s frames.  It will be a few days before the next post – company arrives tomorrow to enjoy the beautiful Arizona weather, so the shipyard will be closed for a few days.

 

 

Share this post


Link to post
Share on other sites

Excellent work Frank B)  B)

 

I beg to differ with Druxey,Vertical scarphs for English ships,but the French scarphed keels horizontally,as this ship was built in Quebec,the latter style may have had some influence in design.

 

Kind Regards

 

Nigel

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to provide support to our members in their efforts to raise the quality of their model shipcraft.

The Nautical Research Guild puts on ship modeling seminars, yearly conferences, and juried competitions. We publish books on ship modeling techniques as well as our world-renowned quarterly magazine, The Nautical Research Journal, whose pages are full of articles by master ship modelers who show you how they build those exquisite details on their models, and by maritime historians who show you what details to build.

Our Emblem

Modelshipworld - Advancing Ship Modeling through Research
×