glbarlow Posted June 15, 2021 Share #31 Posted June 15, 2021 There is nothing the Byrnes saw cannot do, and do better. If you want to keep two saws the reason shouldn’t be because some other saw can do it. (Short of a full size table saw I suppose) The addition of the Byrnes cross cut table accessory opens even more possibilities. I easily cut lap joint hatches for Cheerful using it. Bob Cleek and Canute 2 Quote Regards, Glenn Current Build: HMS Winchelsea Completed Builds: HM Flirt (paused) HM Cutter Cheerful, Lady Nelson, Amati HMS Vanguard, HMS Pegasus, Fair American, HM Granado, HM Pickle, AVS, Pride of Baltimore, Bluenose Link to comment Share on other sites More sharing options...
glbarlow Posted June 15, 2021 Share #32 Posted June 15, 2021 On 3/6/2017 at 6:48 PM, ChrisLBren said: order new blades The best saw blades for the Byrnes saw are the ones he sells. He no longer offers Thurston blades. I have his new ones, they cut great. Canute 1 Quote Regards, Glenn Current Build: HMS Winchelsea Completed Builds: HM Flirt (paused) HM Cutter Cheerful, Lady Nelson, Amati HMS Vanguard, HMS Pegasus, Fair American, HM Granado, HM Pickle, AVS, Pride of Baltimore, Bluenose Link to comment Share on other sites More sharing options...
t5956ws Posted June 16, 2021 Share #33 Posted June 16, 2021 DVM2, Thanks for your response. I must be dense or there is more to it. I know what it is now but I, for the life of me can't figure out how to attach it. The photo shows 2 knobs. The one I can see is going into a much smaller diameter cylinder. Is there a schematic or manual that can be found? Possibly a photo from the bottom from someone. mtaylor and Canute 2 Quote Link to comment Share on other sites More sharing options...
kurtvd19 Posted June 16, 2021 Share #34 Posted June 16, 2021 The part you showed in post #28 is a simple jack that is placed under the blades shaft housing after it is loosened and moves the blade up or down. It is placed right where the two red knobs shown in post #30 are shown. The two red knobs were a later improvement to adjust the blade height. Canute and mtaylor 2 Quote Kurt Van Dahm Director NAUTICAL RESEARCH GUILD www.thenrg.org SAY NO TO PIRACY. SUPPORT ORIGINAL IDEAS AND MANUFACTURERS CLUBS Nautical Research & Model Ship Society of Chicago Midwest Model Shipwrights North Shore Deadeyes The Society of Model Shipwrights Butch O'Hare - IPMS Link to comment Share on other sites More sharing options...
Steve Bergeron Posted May 8, 2023 Share #35 Posted May 8, 2023 If anyone has the paperwork from the manufacturer I would love to get a PDF or photograph of it. I know its a long shot, but if if you have some of the original paperwork left I hope you could share. Steve mtaylor 1 Quote Link to comment Share on other sites More sharing options...
bruce d Posted May 8, 2023 Share #36 Posted May 8, 2023 Hello Steve, What exactly are you looking for? Regards, Bruce mtaylor and Ryland Craze 2 Quote 🌻 STAY SAFE A model shipwright and an amateur historian are heads & tails of the same coin current builds: HMS Berwick 1775, 1/192 scratchbuild; a Slade 74 in the Navy Board style Mediator sloop, 1/48 - an 18th century transport scratchbuild French longboat - CAF - 1/48, on hold Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.