gbl

US Brig Syren by gbl - Model Shipways - Scale 1:64

Hello

 

This is my build log for the US Brig Syren.  New member and per my introduction a few weeks ago, I mentioned starting the kit in the fall of this year.  Changed my plans a little, so hoping over the next few weeks to get to chapter 2 before summer arrives.   Where model ship building is a winter time project for me, over the summer may look at taking my time and fairing the hull while sitting on the balcony.

 

One problem is that I have a bend in the bulkhead former.   I understand chapter 2 stating fair the hull with the bulkheads temporarily in place (and properly aligned) and using a plank to check my work.  Once satisfied, then glue the bulkheads in place.    Then create the filler blocks.  

 

Reading up on dealing with this bend issue and plan to proceed as per another member in this form.  Due to the bend in the BF, think I will look at creating the filler blocks before gluing the bulkheads in place. Then proceed with fairing the hull.   This will allow me to remove the bulkheads to fine tune the bevel individually and confirm that the bend has be removed before any glue applied.   

 

Any advise on this?

 

For now, once the wood strip dries over night, will be gluing this basswood strip to create the rabbet over the next day or so.   This is going to be a fun build.

 

Blaine

1.thumb.JPG.cb0aef5bc9b08a0897f4cdd33825c7da.JPG2.thumb.JPG.ad9b48e7f183b0621e4ed4f2310490df.JPG

 

 

Share this post


Link to post
Share on other sites

Hi

Well 2 nights ago glued the basswood strip to the BF and this evening started creating the rabbet.  Haven't finished but attached photos some idea how I am doing.  This is the first time I have ever created a rabbet and so far don't find it to difficult considering I was concerned about doing this.

 

Using 3 different types of excel hobby knives.  All new.  Planning to do a bit of sanding to with this to smooth out the taper and using a plank 2 get a got good fit.

 

Any advice welcome.

 

Blaine

3.thumb.JPG.e0ee168e98d6d84e80082701045a34bf.JPG4.thumb.JPG.39f9e3e2489a137a60bd5a415c9f0ca3.JPG

 

 

Nirvana, donrobinson and russ like this

Share this post


Link to post
Share on other sites

Looks like a good start Blaine!  I'm very interested in your build as the Syren is the next on my list and I can use all the wisdom these Syren Build logs can offer.  Its great to know what works well and what is a challenge. I've never cut a rabbet either - glad your experience is good.

 

May I follow your build?

donrobinson and Nirvana like this

Share this post


Link to post
Share on other sites

Doug, I didn't even ask permission to follow.

I just pulled up a comfy chair and brought my coffee along.

donrobinson and Heronguy like this

Share this post


Link to post
Share on other sites

Welcome all to the build log.   This evening continued work on the rabbet and should have completed tomorrow evening.   So far pleased with the fit of the plank against this but will get a better idea when play around with the keel dry fitted in place tomorrow.

 

Blaine

Share this post


Link to post
Share on other sites

Some pictures of the further work on the rabbet and fitting the garboard plank and keel in place.    Re the last picture, have a little problem with the fit of the false keel meeting the slot on the 

stem.   A gap of a mm or so.   Anyone else encounter this?   If so a solution.     Have to think about it and check some other builds.    Don't want to sand anything at this point and find out down the road I have another problem when copper plating.  

 

Blaine

5.thumb.JPG.252f54ccf8dddcfe697a0518737e018d.JPG6.thumb.JPG.1209ad078da2f4a74a3faf93888feff9.JPG7.thumb.JPG.878eb70f8fcc3380a16f3d3e5622a066.JPG8.thumb.JPG.b538bab224f9fbbb7c539602138a246f.JPG

Ryland Craze and Nirvana like this

Share this post


Link to post
Share on other sites

Latest on my Syren.   Glued the keel and stem yesterday.    This evening removed the clamps and attached the false keel with small nails.  Then installed bulkheads in place to check the garboard plank.  Satisfied with its fit into the rabbet and its alignment with the bulkheads.   So the rabbet turned out quite good.   Didn't get a picture of this but tomorrow evening may dry fit again to take a second look to be sure.   

 

Attached picture my attempts to also start the process of aligning the bulkheads with BF.  My plan as mentioned in my first post, to cut the bulkhead fillers and dry fit everything in place.  Have a slight warp / twist in the BF pass the mid section toward the stern so want to make sure I can correct this problem.   Certain I can and understand per the comment in chapter 2 this is one of the points of the filler blocks.    

 

Blaine

IMG_3207.thumb.JPG.1d7ed4b28b7eb12214caaa32584fd32d.JPG

Nirvana and Ryland Craze like this

Share this post


Link to post
Share on other sites

Have to say the instructions supplied with this kit are excellent.  I have never encountered this with any other build.   Makes it so much more enjoyable.   I read each chapter several times and although only on chapter 2 started reading up on the chapter 3 and 4 yesterday evening and again this evening.   As many members have said and from my own experience, I find it very useful to stay ahead of the actual build by reading ahead of time.  This forum also helps tremendously in that regard.    So a big thank you to all.

 

Per my post last night, re checked the garboard plank against the bulkheads and rabbet.IMG_3211.thumb.JPG.bb800867c1e744d6f1263fee926a6aff.JPG

Also this evening began squaring up the bulkhead / BF and creating the filler blocks.  Maybe a few days on this.

 

Blaine

IMG_3212.thumb.JPG.b0d51c764c9e630b9fdba94bb295a1d4.JPG

Ryland Craze, Nirvana and STSCM like this

Share this post


Link to post
Share on other sites

I'm interested to follow your progress, as this is on my someday list.

Share this post


Link to post
Share on other sites

Welcome Eric and Steve

 

Last few evenings working on the balsa filler blocks.  I cut them out from a 12" x 3" x 1" balsa block and then sand for a snug fit.  Prior to fitting, I check for the bulkhead alignment using a couple of 2 inch engineer squares and several small right angle squares that I clamp to the bulkhead and BF (re images in prior post).   Little over 50% completed.   Not a difficult job.........balsa

very easy to work with.   When completed, will remove from the slip to check for the removal of the keel warp / twist.   If ok, will then proceed to fair the hull.

 

Blaine

 

IMG_3216.thumb.JPG.3af79b7c3755c0f3bc3c0eb9db8f2b54.JPG

IMG_3217.thumb.JPG.7c4c3f478f9fa95699da55b273156239.JPG

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.