Jump to content

Can you water bend glued wood?


Recommended Posts

I wouldn't recommend it for a number of reasons.  Once glued, then soaked, the planks may come off as the water dissolves the glue (true of steaming also).  Also, wood needs to compress or expand as it is bent in one direction or the other.  You will have differing rates of compression on the outer and inner sides.

 

Best to place the bulwarks first I think.

 

cheers

 

Pat

If at first you do not suceed, try, and then try again!
Current build: HMCSS Victoria (Scratch)

Next build: HMAS Vampire (3D printed resin, scratch 1:350)

Built:          Battle Station (Scratch) and HM Bark Endeavour 1768 (kit 1:64)

Link to comment
Share on other sites

In a word "no". As Pat explained the expansion/compression will cause problems, in addition if you use a water based glue it will come undone whilst soaking. It's not that hard to pre-bend and then fit the inner planks - just need a lot of clips to hold it firmly on the bulwarks as you glue it.

 

Link to comment
Share on other sites

No... I wouldn't recommend it either. Easier to put the bulwark and then, if needed, bend the individual planks as stated above. You may not even need to pre-bend the planks, just press them hard against the bulwark while the glue dries.

There aren't but two options: do it FAST, or do it RIGHT.

 

Current Project Build Log: Soleil Royal in 1/72. Kit by Artesania Latina.

Last finished projectsRoyal Ship Vasa 1628; French Vessel Royal Louis 1780. 1/90 Scale by Mamoli. 120 Cannons

 

Future projects already in my stash: Panart: San Felipe 1/75; OcCre: Santísima Trinidad 1/90;

Wish List: 1/64 Amati Victory, HMS Enterprise in 1/48 by CAF models.

 

So much to build, so little time!

 

 

Link to comment
Share on other sites

An easy way to bend these is with a old curling iron.  Put them in water for about 10 minutes, then use the curling iron to bend them into shape.  Let cool and Bob's your uncle.

Mark
"The shipwright is slow, but the wood is patient." - me

Current Build:                                                                                             
Past Builds:
 La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD           Triton Cross-Section   

 NRG Hallf Hull Planking Kit                                                                            HMS Sphinx 1775 - Vanguard Models - 1:64               

 

Non-Ship Model:                                                                                         On hold, maybe forever:           

CH-53 Sikorsky - 1:48 - Revell - Completed                                                   Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)         

         

                                                                                                                                                                                                                                                                                                

Link to comment
Share on other sites

If you were to fabricate the multi layer bulwark complex and then bend it:

If the glue joints survived the stress -  which is not likely.

If the interior components did not break due the the compression force  -  depending on the species of wood, also unlikely

The interior components would be applying force to reverse the bend.

 

If you pre bend each layer and then assemble it, the interior components will help hold the bent shape.

NRG member 45 years

 

Current:  

HMS Centurion 1732 - 60-gun 4th rate - Navall Timber framing

HMS Beagle 1831 refiit  10-gun brig with a small mizzen - Navall (ish) Timber framing

The U.S. Ex. Ex. 1838-1842
Flying Fish 1838  pilot schooner -  framed - ready for stern timbers
Porpose II  1836  brigantine/brig - framed - ready for hawse and stern timbers
Vincennes  1825  Sloop-of-War  -  timbers assembled, need shaping
Peacock  1828  Sloop-of -War  -  timbers ready for assembly
Sea Gull  1838  pilot schooner -  timbers ready for assembly
Relief  1835  ship - timbers ready for assembly

Other

Portsmouth  1843  Sloop-of-War  -  timbers ready for assembly
Le Commerce de Marseilles  1788   118 cannons - framed

La Renommee 1744 Frigate - framed - ready for hawse and stern timbers

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...