Jump to content

US Brig Syren by svein erik - Model Shipways - 1:64 - 18 gun brig


Recommended Posts

Svein,

 

I would think twice about adding brass tree nails on the black wales. That contrast might be too much. Black treenails might be better, and I believe more authentic, even though they may not be seen very well.  Perhaps you should do a small section first, and if you don't like it, you could probably paint over them.

 

Just my amateur opinion.

Link to comment
Share on other sites

Thanks for the liks 

I yust finish all the treenail and the wales 

I have also painted the wales and stern with 10 cotes ,but more needed for later

I need to get the plank under the wales on board and the garboard plank before I line off the rest of the hull

 

Svein.erik 

20180420_110912_resized.jpg

20180419_212753_resized.jpg

20180420_193106_resized.jpg

20180420_193100_resized.jpg

20180420_193131_resized.jpg

Link to comment
Share on other sites

It is hard to tell at long distance, but you are having some problems Erik. Before you go further, may I suggest you replace the black tape with thread? This minimizes the thickness issue. I'm attaching a version of your photo with red lines showing roughly how the lines should go. Note that the lowest planks at the bow, especially the garboard, end earlier to allow enough room for the rest of the planking. At the stern the lowest planks widen at the stern post. Try again and play with the thread positions until you get smooth curves from every angle of view.

 

Have you read A Primer for Planking, pinned on this site?

Lining off.jpg

Be sure to sign up for an epic Nelson/Trafalgar project if you would like to see it made into a TV series  http://trafalgar.tv

Link to comment
Share on other sites

Thanks 😊there are 3 planks inkl the garboard planks (5/32 and 2 planks 1/8)

and you ar spott on , my baw looks something from hear to there😲

I have post some photo erlier of the hull before I plank the upper dekk (upgrade wood castello boxvood )

 but am not sure about planking the garboard  befor I line of the hull 

I my have to take it off and line off the hull 

make new garboard using the tic marks?

 

Svein.erik 

20180314_212155.jpg

20180314_212041.jpg

Link to comment
Share on other sites

Erik: there are so many things to consider when lining out. Please read the article (link below) to better understand what you need to do. Also, there are a lot of boat-builders in Scandinavia. Perhaps you could talk to one of them as well!

 

https://modelshipworld.com/index.php?/search/&q=a primer on planking&sortby=newest&search_in=titles

Be sure to sign up for an epic Nelson/Trafalgar project if you would like to see it made into a TV series  http://trafalgar.tv

Link to comment
Share on other sites

Hi Erik,

You probably already have, but study Chucks manual in depth. I read it 5 to 6 times and sometimes still picked up something I didn't see before. His photos show the order of placing the planks and where to end them to allow for the next one's. I wasn't very confident at this stage but got there in the end following the process outlines in the instructions.

Your model is looking great.

Cheers,

Current Build:     USF Confederacy 1778 - Model Shipways - 1:64

 

Completed:         US Brig Syren - Model Shipways - 1:64

                        San Francisco Cross Section - Artesania Latina - 1:50

Future build:        HM Granado - Caldercraft - 1:64

                        LeRenard - Artesania Latina - 1:50

Link to comment
Share on other sites

  • 2 weeks later...

The planking looks very nice.  You did a great job lining out the hull.

Ryland

 

Member - Hampton Roads Ship Model Society

            - Ship Model Society of New Jersey

               - Nautical Research Guild

       

 

Current Build - Armed Virginia Sloop, 18th Century Longboat

Completed Build - Medway Longboat

Link to comment
Share on other sites

  • 2 weeks later...

Hi  again and thanks for the liks 

the summer is here So I have work to do outside the shipyard (yust to keep my wife happy😉)

But I did finish the 2 belts with boxvood and its time to get over to use basswood 

am over the critical point at the stern, 

The black paint wil have castello boxvood, I my have overdue this but Wats fun in that 😆

 

Svein.erik 

20180522_223759_resized.jpg

20180522_223706_resized.jpg

20180522_223912_resized.jpg

20180522_223510_resized.jpg

20180522_223608_resized.jpg

Link to comment
Share on other sites

Erik,

 

Shorten the garboard back a bit, and change the shape at the bow to better follow the current run of the planks. You should be able to fit all of the strakes in that way. 

 

Good progress. 

Joe Volz

 

 

Current build:

Model Shipways "Benjamin W. Latham"

 

 

Completed  builds on MSW:

Caldercraft HMS "Cruizer   Caldercraft HMBV "Granado"   Model Shipways "Prince De Neufchatel"

 

 

 

 

Link to comment
Share on other sites

17 hours ago, jwvolz said:

Erik,

 

Shorten the garboard back a bit, and change the shape at the bow to better follow the current run of the planks. You should be able to fit all of the strakes in that way. 

 

Good progress. 

Thanks for the coment ,

as I did this hum#**/&%+...... 😲 am thinking of using a drop plank to do the task here

and take this with me on the nex build 

as the syren get's the copper plates it vil not been seen 

 

Svein.erik 

Link to comment
Share on other sites

Hi everyone, 

I did resive corronades from shapeways to use on the syren,

but I did order the hole set with the sledge in 1:64 scale

but it Seems to me that the sledge is to big but the corronades is in scale

so I need to send a mail☺

price is 54 dollar vs 181 from cornwall

 

Svein.erik 

20180606_131214_resized.jpg

20180606_131111_resized.jpg

20180606_131118_resized.jpg

20180606_132413_resized.jpg

20180606_132039_resized.jpg

Link to comment
Share on other sites

I am pretty intrigued myself by this 3D printing approach. How is the quality of the carronade barrels? Once painted is a 3D printed barrel comparable to a brass barrel with respect to precision and details?

Btw, you do a really good job on your Syren model! I love to follow the progress.

 

Thomas

Current Built:   Model Shipways  Syren  (US Brig 1803)

 

Last Built:        Anfora (kit bashed)  Ictineo II  (1st steam powered submarine 1864)

 

Link to comment
Share on other sites

Thanks Thomas

I do Not know how it wil look wen painted I yust resive it to day,

I also noted that the slegde is to wide back and a little to long (ref.plans)

I have mail them and sendt photo of the items and the plans,

they are already responding so I have to see wat the wil do with this problem☺

 

Svein.erik

Link to comment
Share on other sites

The answer Thomas depends on the 3D printing process. The machines that Shapeways uses are the highest quality. I am very impressed.

Current Builds - 18th Century Longboat, MS Syren

Completed Builds - MS Bluenose, Panart BatteStation Cross section, Endevour J Boat Half Hull, Windego Half Hull, R/C T37 Breezing Along, R/C Victoria 32, SolCat 18

On the shelf - Panart San Felipe, Euromodel Ajax, C.Mamoli America, 

 

Its a sailor's Life for me! :10_1_10:

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...