Jump to content

Sultana 1767 by moreplovac - FINISHED - Model Shipways - 1/64 - Colonial Schooner


Recommended Posts

 

I changed my mind, was not spending time making one collar with two eyes. Instead i decided to redo the hearts.

 

The collars were seized with .18mm rope. Here is a brief overview of seizing setup and one view thru magnified glass. Needed, for sure.

 

IMG_3500.thumb.JPG.d37a6b8d0da37f34624f218e7ca15e97.JPG

 

IMG_3499.thumb.JPG.bd83ef2a036565273e25bc943d836775.JPG

 

Three were completed, seized and ready for next step. One appears to be attempting to escape..

 

IMG_3501.thumb.JPG.b5f93dd83756da278c5ed22ce5a248a1.JPG

 

The collars were mounted to the bowsprit; three of them, following practicum steps. They were secured with single overhand knot, secured by touch of glue. The loose ends were cut with nail clipper; it is used only for this purpose, i swear.

 

First collar assembled on bowsprit..

 

IMG_3504.thumb.JPG.04e417e57ccd621858ac9cb323ab789c.JPG

Then second..

 

IMG_3505.thumb.JPG.c0e5fdc311adb30d30f1ae0c2ad28066.JPG

.. then third..

 

IMG_3508.thumb.JPG.02a9d7e4766b8abd686fcf649eb51fa5.JPG

IMG_3507.thumb.JPG.d4516cde013621ed641097a682f57468.JPG

..then one of the open hearts was installed on bowsprit...

 

IMG_3509.thumb.JPG.93dc176ecee7969e1195a31c7ec640ed.JPG

 

IMG_3511.thumb.JPG.4a49a48bb2c920e0f869910307c52e55.JPG

 

IMG_3510.thumb.JPG.4c7ec5afa03c3cdc13c306b3fe96e9f4.JPG

 

The open heart was a bit of a challenge to put in; ropes just did not want to stay put. I had to use scotch tape to fix the open heart to position, then i was able to properly tight the rope, glue it and cut loose pieces..

 

The hearts were next. Cut them again from a piece of boxwood, in correct size, and sanded to proper shape. Then a grove was made on the edges, and rope (.45mm) added around them. Before, hearts were dipped into golden oak stain, extra stain was removed with a piece of bounty. The rope was put around the hearts with assistance of a glue to keep them in correct place. Seizing was also done using .18mm black rope.

Just to mention that amount (and size of ropes) that is included in the kit is not quite appropriate so i decided to order some ropes from Syren company. Just to make sure i will not run out of ropes during assembly process.

 

IMG_3513.thumb.JPG.6f53b99a0830117d75a87daa359c6c66.JPG

 

IMG_3514.thumb.JPG.7e8e3088ab820ab3fee9a6c6cdceb870.JPG

 

IMG_3515.thumb.JPG.0a81d3026a86ebea05b139f967251b98.JPG

 

I will put a layer of varnish on the hull to protect it from element. Once dried i will put some bounty around the hull to have it protected while handled..

 

Happy modeling.

 

 

 

 

 

 

 

 

 

 

Link to comment
Share on other sites

That  is some impressive work.

Lou

 

Build logs: Colonial sloop Providence 1/48th scale kit bashed from AL Independence

Currant builds:

Constructo Brigantine Sentinel (Union) (On hold)

Minicraft 1/350 Titanic (For the Admiral)

1/350 Heavy Cruiser USS Houston (Resin)

Currant research/scratchbuild:

Schooner USS Lanikai/Hermes

Non ship build log:

1/35th UH-1H Huey

 

Link to comment
Share on other sites

 

Work continue with masts....

 

Both masts, foremast and main mast, are identical in shape with difference in length. I will follow up mast plan that is provided in kit with small additions from practicum. I don't have that many Sultana' plans to combine details so i am staying with a kit plan.

Wooden dowels supplied with the kit are slightly twisted and pretty much unusable. I don't have any close by hobby shop so trip to my homedepot ended up with few dowels in different size but they are also not quite straight. I might be able to use few smaller parts but for Sultana' masts i have to dig in my other wood pile. So, decided to go with poplar as i have few leftovers from some other projects in my house. Poplar is a bit yellowish and a bit harder to carve but less likely to snap during lathe work (as happened to me with other type of wood dowels) and with golden oak stain, it will be slightly darker comparing to rest of the ship parts. So i will make all mast parts out of the same poplar stock.

 

Before i made decision to go with poplar i tried to use homedepot' dowels and made foremast out of 8mm dowel.

Well i made it fairly decent at the end but decided not to use it at all as final product.

 

Foremast made from homedepot dowel..

IMG_3522.thumb.JPG.ca3f5e260720e04d46ddd7b69fa3de94.JPG

So back to the poplar pile. I cut 8mm x 8mm square rod, a bit more lengthy that mast dimension. This is a small rod and i have to round one end so it can fit into lathe. Borrowed my old pencil sharpener and made basic round shape; with a knife the round part become long enough to stick safely in lathe chuck.

 

IMG_3524.thumb.JPG.f5e6fffbb4ec61a5f4d6ac8bb35ea8ee.JPG

After some time and two usage of shop vacuum to remove all dust, here is result..

 

IMG_3525.thumb.JPG.20df30073792fd7ba9881d017d7169a3.JPG

Then with assistance of home made sanding blocks (size 50), small rasps and few other type of files, i made a fore mast..

 

IMG_3523.thumb.JPG.1d787b9016c89924f40dac7d16d1b692.JPG

IMG_3526.thumb.JPG.2aa536f718b629ce92543be1fc6da562.JPG

Both masts were carved from poplar rods..

 

IMG_3527.thumb.JPG.fd21575e5da3336f9275611d8d1b0ab0.JPG

The top will be painted in black and the rest will be stained in golden oak stain.

 

The both top masts were build next. Poplar rod cut in square, 5mm x 5mm in correct length. Same thing with rounding at one end to fit into lathe' chuck and shaping can start...

 

Here is final product. I made one top mast today, will continue tomorrow time (and New Year celebration) permitting..

 

IMG_3531.thumb.JPG.41662943574dbe26a8c97ea080cddedb.JPG

 

IMG_3534.thumb.JPG.0b903e207c17d04cfc1225a89ca6d1da.JPG

A little bit extra length at the bottom will be altered later.

 

The bottom, squared part...

 

IMG_3533.thumb.JPG.80f59c83cb8ea2deb43784dfd87bf83e.JPG

 

Process of making top part with a ball truck...

 

IMG_3529.thumb.JPG.a15fecfdf5063cf22d518a05dd28ca7b.JPG

And final result... That was a little extra wood at 3mm part that i removed after taking this picture.

IMG_3532.thumb.JPG.a46a713d4d7ce50ebda22dc407e9cb5c.JPG

So, this is for today..

 

Best wishes to all and happy New Year..

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Link to comment
Share on other sites

Work on masts continued in the new year...

 

Completed top foremast ...

 

03.thumb.JPG.90f3348c26e9b669fe8838802e201f39.JPG

.. and during shaping process.. This one is process of shaping top part of the mast, with ball truck..

 

02.thumb.JPG.e2a9508e5160c7969bcc7ab9ae932643.JPG

 

End the main boom was carved as well.. Again poplar rod was used, first cut in 5mm x 5mm x correct length, square shape, then end piece was rounded to fit into lathe 3-piece chuck and carved to the correct shape. This way i will have all mast parts carved from the same type of wood. Once stained and varnished they will look nice.

 

04.thumb.JPG.76c10219dbf57731d9ffc9116e99b294.JPG

Happy modeling.

 

 

 

 

 

 

 

 

 

 

 

 

 

Link to comment
Share on other sites

 

Cast trestle trees provided with a kit were not very nicely made. It can be used though but i decided to build my own version. They are easily made from scratch wood. First i made a drawing by measuring one tree provided in the kit then accommodating dimensions slightly to fit my masts properly. Below is a "technical drawing"..

 

IMG_3558.thumb.JPG.4765531dcf9e0ea06e9283be340427fe.JPG

At the end, both holes will be square, the drawings will be used for a top tree as well as lower. The top tree will require a circle hole to hold the upper part of a topmast. The holes were pre-drilled and squared with a file.

 

IMG_3553.thumb.JPG.acd454fb1b783f10ccaa29fe3c4ac8b8.JPG

IMG_3552.thumb.JPG.e6106c3459bfb8db44554872a501ec82.JPG

The top part of a tree is a bit oversized; it will be shaped to the correct length once all pieces are glued. The reason for this longer part is to have a bit more wood to hold with hands during construction phases.

 

IMG_3555.thumb.JPG.e3f60a19920cefefc472b845a0ffe984.JPG

IMG_3554.thumb.JPG.24807262e31e02c9b9d10e820bd81858.JPG

Then the tree was cut to the required dimension and whole assembly was shaped with sand blocks of different size.

IMG_3559.thumb.JPG.a549c0b3f4b5873205ac1a4cac173050.JPG

And testing with a topmast...

 

IMG_3556.thumb.JPG.3e562ad4d76f1d4fe72d0bdde8fe7181.JPG

I slightly deviated from practicum while building this part.

To make sure that both trees are identical as close as possible, i used a piece of scotch tape, have it on a side of the tree, trace the shape with a pencil and transfer scotch tape on another part of the scrap wood. Another way will be to have all four parts hold by wise and shape them all at once but did not think about this approach ahead of time...

 

The main mast was also completed with trestle tree; they will be painted in black and small eye bolts will need to be attached to. Next will have to make a nine mast hoops per mast before making a boom rest on main mast. Foremast will have just a small chock on the aft side of the mast. 

 

Happy modeling.

 

 

 

 

 

 

 

Link to comment
Share on other sites

Nice work.

 

I don't know how the original pieces from the kit would have turned out but your scratch built ones are great.

Lou

 

Build logs: Colonial sloop Providence 1/48th scale kit bashed from AL Independence

Currant builds:

Constructo Brigantine Sentinel (Union) (On hold)

Minicraft 1/350 Titanic (For the Admiral)

1/350 Heavy Cruiser USS Houston (Resin)

Currant research/scratchbuild:

Schooner USS Lanikai/Hermes

Non ship build log:

1/35th UH-1H Huey

 

Link to comment
Share on other sites

 

Seven mast cleats were glued around both masts. The cleats were obtained from Syren ship model company since the kit provided were a bit oversized. The cleats are laser cut and looks very nice. The location was marked with painter' tape and few dots to approximately shows the seven points were cleats will be glued. All cleats were painted black before being mounted.

 

IMG_3565.thumb.JPG.4f1e2236d9a6f5310ed25c4ba84fcfae.JPG

 

IMG_3567.thumb.JPG.b1e158dd109f414f049e9b5537a9c723.JPG

 

The boom rest was added to the main mast. For this i followed the practicum and made a half of a circle. The plan shows the full circle. I drilled the hole (6mm) in the scrap piece of dowel by increasing the diameter of the drill. Then cut the ring and divided into two parts..

 

IMG_3568.thumb.JPG.785345b0d2a3d10f0a4fd473fc7ef345.JPG

A bit of a shaping was applied to the part and it was glued to the mast. Under the mast i put three small chocks on the aft part of the main mast. The chocks were then shaped to the correct shape... This is a view thru the magnified glass. All parts were shaped with a file and cleaned with a sanding block. On the foremast there was only one chock glued to hold the hoops. The layer of red paint was applied after.

 

IMG_3570.thumb.JPG.050c55a9442416dc694c8e3f9325b53f.JPG

The hoops were build out of office folder (manila folder). The folder was white and it was stained in golden oak. Then about 20 of them were cut in 1mm width. The length was about 25mm.

 

IMG_3563.thumb.JPG.06e9a882b4ec694ae88d0ad4bcd6be64.JPG

IMG_3564.thumb.JPG.ae4505d956c96601a0829a09f4f42601.JPG

I wrapped the strips over a wider dowel, over lapped the ends and glue them with super glue. The excess was cut with a scissors and they were mounted on the masts before any work on cleats was started.

 

IMG_3572.thumb.JPG.2c9ae180991a2508df03d3a2310e644c.JPG

IMG_3573.thumb.JPG.28a7c40912a2c5855d3963b1e11ae534.JPG

Then they were stopped to move on mast with some painter' tape so i can hold the mast while working other parts.

 

So the whole assembly so far looks like this:

 

IMG_3574.thumb.JPG.12056b92ef57af46102a0a70c90b8fc5.JPG

And temporary on the ship looks like this:

IMG_3575.thumb.JPG.7fe9888a9001c80c5f4fdde5a3c12212.JPG

Happy modelling.

 

 

 

Link to comment
Share on other sites

  • 2 weeks later...

 

 

Few days ago i was looking to my simulated mast hoops and did not like to overlap that was created by gluing the manila folder strips. So i decided to take shot and see if i can make a wooden mast hoops in the same dimension. First i find a dowel in correct outside diameter and drill a hole in it. I put a dowel into my lathe, on the other end i secured a drill bit in 6mm size, turn on lathe and slowly move the drill towards the rotating dowel. The center was slightly off centered but nothing that a bit of sanding cannot fix 🙂

 

20190115_210503.thumb.jpg.5d8f95ff0850619b4777d127defe2850.jpg

Then i cut first hoop using handsaw..

 

20190115_210450.thumb.jpg.c9128da51f65c321160650093f4af453.jpg

Testing on the mast appears to have better results than one made out of folder.

 

20190115_210522.thumb.jpg.57229382b704684dfe52d54fc769f298.jpg

So, now since my masts were all completed i was in dilemma what to do to accommodate wooden hoops: to cut the mast at the area where hoops will be mounted and slide wooden hoops or to make a brand new mast... Next picture has an answer to this...

 

20190115_210420.thumb.jpg.81e8e4a437b00d33a5701bd341d75689.jpg

There are few other gotchas i discovered on masts like diameter was not equal all around mast which i did not notice before, cleats were not positioned correctly, etc. Anyhow, i have completed main mast, it is ready to shape and finish both trestle trees; the rough construction is done, some pieces are still to be done....

 

And my Sultana now rests and anciently waits for mast to be completed and to start rigging...

 

 

20190115_210604.thumb.jpg.a031e81d7362bc1ddeb8bfd28d64048f.jpg

... with Greek warrior guarding the ship.

 

Happy modeling

 

 

 

 

 

 

 

 

Link to comment
Share on other sites

Work on foremast has been completed; actually just making a foremast and trestle trees, there are few other items still waiting...

 

The process was the same as before; cut a piece of poplar, 8mm x 8mm...

 

20190116_192853.thumb.jpg.ad4267ac07a3958792f137eadf919104.jpg

One end was sharpened to fit into lathe chuck...

 

20190116_192859.thumb.jpg.f82ed39237d591d30d38c375debb5295.jpg

Then was mounted into lathe....

 

20190116_193527.thumb.jpg.190b04d22889038383c57d84cb02a0c3.jpg

During shaping process using file and sanding blocks in different size...

 

20190116_195352.thumb.jpg.8667cf15c30522595859fb49156edcaf.jpg

Completed...

 

20190116_201636.thumb.jpg.fb54ee90e53e6672adca4417b61861c5.jpg

And after trestle trees in rough dimensions were added..

 

20190116_212156.thumb.jpg.6b00b2b3a735917b911494b84fe142f8.jpg

The layer of golden oak stain was applied to foremast as well..

 

Happy modeling.

 

 

 

Link to comment
Share on other sites

 

 

A bit more work on trestle trees. I used my old trestle tree template and made 4 parts. A piece of scotch tape helped transferring shape onto scrap piece of wood.

 

20190117_205136.thumb.jpg.fd04e02161794caadfa1a2966a75e8cc.jpg

After some cutting, shaping, more shaping and some amount of wood filler both masts have trestle tree mounted.

 

20190117_211058.thumb.jpg.b124483d193c2db6f85ee90b72372a0c.jpg

20190117_211102.thumb.jpg.527a05371b6fcd8152c709cc38e53333.jpg

20190117_211735.thumb.jpg.0699769df172b4ce3acb2d03751da1e0.jpg

20190117_213739.thumb.jpg.f5c40017ef376d81a99ea91f4b764b81.jpg

The trestle trees will be painted black so wood filler is not a problem.

 

The hoops were sanded lightly, during which process i broke three hoops. There are tiny, very tiny...

 

20190117_223011.thumb.jpg.65f36050a22aed840d04d3f61f3e88a0.jpg

Then they were dipped into golden oak stain, and left drying for overnight.

 

20190117_223851.thumb.jpg.94ac291ef3b4776b259b43ae6e5c160a.jpg

Then i made a half-ring chock that will be mounted on main mast...

 

20190117_214217.thumb.jpg.cfe6b3631c57bae7d5ac8f5ef5cb2986.jpg

After cutting it and shaping it, i almost made mistake to glue it on the mast before putting hoops on it.

 

20190117_215932.thumb.jpg.ab10a796b311fdc824714099b779c1b7.jpg

Today, time permitting i will continue with masts.

 

Happy modeling..

 

 

 

 

 

 

 

Edited by moreplovac
Link to comment
Share on other sites

15 minutes ago, moreplovac said:

almost made mistake to glue it on the mast before putting hoops on it.

That would have been a shame after all this redo. It does look like it was worth the effort though, nice work.

Lou

 

Build logs: Colonial sloop Providence 1/48th scale kit bashed from AL Independence

Currant builds:

Constructo Brigantine Sentinel (Union) (On hold)

Minicraft 1/350 Titanic (For the Admiral)

1/350 Heavy Cruiser USS Houston (Resin)

Currant research/scratchbuild:

Schooner USS Lanikai/Hermes

Non ship build log:

1/35th UH-1H Huey

 

Link to comment
Share on other sites

 

First thing first. To make sure i don't forget hoops again, they were mounted and secured from not slipping away with a scotch tape and some wood to make a bump on the mast. Then i mounted a boom rest on main mast and a chock on fore mast.

 

20190118_201648.thumb.jpg.43e846791f2343b5e907116cb514bf72.jpg...

20190118_201912.thumb.jpg.5ab536f99a41d79553b7eeaec581b754.jpg

A little bit of shaping was done on them.

20190118_204707.thumb.jpg.dac59b71a4e096cab726c566b9d1bed8.jpg

Protective line of tape was applied to border red and black color.

 

And my Greek warrior making sure i do not make any more booboos..

 

20190118_204759.thumb.jpg.171fd99143261af185ed01d0120e9c46.jpg

 

Painted and ready for a next layer of paint. I diluted red and black color to make it as smooth as possible after painting is done. It might take few more layers...

 

20190118_205708.thumb.jpg.7f59769f2371c63fafabf5a392118375.jpg

Happy modeling.

 

 

 

 

 

Link to comment
Share on other sites

 

The bowsprit was mounted today. I glue it with a carpenter' glue to have some time to position it properly.

IMG_0002.thumb.JPG.7e0b3a9e6e2886195f4b16b2c44d940e.JPG

The gammoning for the bowsprit was done with .028 black rigging line. Kit does not have any detailed instructions how to run it. Not sure why is this, but the gammoning is very visible on completed ship. Practicum does have correct instruction borrowed form kit supplied manual for Fair American model. First i started by seizing a small eye into the end of the rigging line and after that followed procedure in practicum illustration.

The end of the rope was freezed with a touch of glue so it can go thru small openings fairly easily..

 

IMG_0001.thumb.JPG.c4e54ef867f36284d85d6dff8c1612da.JPG

IMG_0003.thumb.JPG.d751b77f37dbee037a99fc0e413ca2df.JPG

IMG_0004.thumb.JPG.42a2c01b38e2affe957e376f6eafae42.JPG

IMG_0005.thumb.JPG.fe4aa4f60b0ea9af308e35bf6aba63c2.JPG

 

IMG_0006.thumb.JPG.8b7e480630b0ed2d2d0ca0f01f62ea78.JPG
 

IMG_0007.thumb.JPG.9fc2579298c331263c112de89ab6e993.JPG

 

IMG_0008.thumb.JPG.b61fcc03247f51795c15c35ba8d0d43b.JPG

IMG_0009.thumb.JPG.d3748b78228a9e669142fcdb01efab95.JPGIMG_0010.thumb.JPG.173ab7b511b11206faa47194ee8209ec.JPG

Then i framed a bowsprit with .75mm basswood strips with correct 45 degrees angle, like a real molding.

 

IMG_0011.thumb.JPG.d52c0caab545c5384b58a1fb267a983e.JPG

IMG_0012.thumb.JPG.0408dd36c46020a7a5330c1b30fb3699.JPG

Then i run another layer f black paint on trestle trees and mounted masts just for fun...

 

IMG_0013.thumb.JPG.f6fa008a0c8f547e1bc9feb8b8daefda.JPG

 

Getting there...

 

Happy modeling

 

 

 

 

 

 

Edited by moreplovac
Link to comment
Share on other sites

 

The work continue on boom; the boom was already made out of a piece of poplar dowel since all kit supplied dowels are mostly not appropriate and warped. The yaws for the boom were traced from the plan on a piece of wood. I took slightly different approach for this part.

IMG_0028.thumb.JPG.1fc857232f177e7ed0308c841101dd66.JPG

The whole assembly was traced on the paper and to the bass wood sheet, place for a boom was cut in the middle; then the boom was inserted into, glued to the wood.

 

The yaws were then cut from the wood, one end at the time. 

 

IMG_0029.thumb.JPG.e4f4678b5b2bc62f660e6891d6521ccf.JPG

The shape for jaws were adjusted and holes for parral beads will be drill later. I think i can manage it without breaking these fragile jaw ends.

 

IMG_0030.thumb.JPG.d29270878e9549d2dd0b1be07adbb027.JPG

 

Eye bolt, cleats, iron bands (simulated by electric tape) are mounted and sheaves were made too. The sheaves were made out of two small piece of bass wood, first traced from the plan. These are very tiny...

 

IMG_0031.thumb.JPG.56e76ac39eee56848c9509056509d332.JPG

The boom was received a layer of golden oak stain to match other parts of the ship.

 

IMG_0032.thumb.JPG.53c9418d083152a769f4247e814e835b.JPG

I added one extra cleat and that one was removed later and place were it was glued was sanded with no traces of mistake..

 

Happy modeling.

 

 

 

 

 

Link to comment
Share on other sites

 

Well, i have tried and decided to go with model that represents Sultana after figure head was removed by Royal Navy after it was purchased. According to practicum it was not clear if figure head was replaced with something else.

This detail will definitely make the model more interesting but unfortunately my carving skills and available tools i have, are not up to the challenge and i will need to pass it for this time.
 

IMG_0047.thumb.JPG.e335dbaf4736c9ce6d287373282ecee1.JPG

These are my two attempts to carve the figure. Also tried to go with practicum and experiment with sculpey but was not sure how can i remove the figure form the ship to get it baked once i carve it to acceptable level. It would be very easy to damage the figure during removal process.

 

I bit more research and practice will make it perfect for some other building attempts. For now, no figure..

 

Happy modeling

 

 

 

 

 

 


 

Link to comment
Share on other sites

 

To make it up for figure head i decided to rope the bowsprit. First i drilled the pilot holes for eyebolts that will hold the shrouds. Then the eye bolts were dipped into blackening solution for few minutes, dried and mounted to the ship.

 

Then i measure the length of laniards from the plan and used a piece of wire to have a template that will use for all laniards for all shrouds.

 

IMG_0034.thumb.JPG.800012511d95a9bc3d1d8484252a0d9b.JPG

For the purpose of keeping the lines tight, i had to modify an alligator clamp and file all those sharp teeth. Then inserted a piece of wood in up and bottom part, sharp it so it can close flat...

 

IMG_0035.thumb.JPG.c8a5f2326785fd1c4a6a13f6ef5ebb85.JPG

First shroud completed.

 

IMG_0036.thumb.JPG.de609acbe4332b40122b6b3c84e8a02e.JPG

IMG_0040.thumb.JPG.9f6e95a89de3add7b952f13cef48a13b.JPG

For laniard i was using tan ridding, as per practicum and ended up to be interesting.

 

Second shroud completed.

 

IMG_0039.thumb.JPG.36d1884d65c8497d6ccd9b21c6a433e4.JPG

 

IMG_0038.thumb.JPG.441d077c710d2bb2b996dab9b971f5f0.JPG

Then i started to rig the bobstay. IT was rigged with black rigging line, doubled along its entire length.

 

The process of keeping the rigging line tight was a bit of a challenge but i made it thru.

 

IMG_0041.thumb.JPG.05735cf699cd07a1e38855d0009a2e16.JPG

So the end result for today...

 

IMG_0042.thumb.JPG.f1b3a1d2f8bf8e1cbfa939962786e57f.JPG

IMG_0043.thumb.JPG.616aaac93b7159290252bb6b5b3a4bf8.JPG

IMG_0044.thumb.JPG.02fc473d7ec4f952a7f5311ecefa5c11.JPG

IMG_0045.thumb.JPG.4d77efc62a637dbcf12d6bafdfbd7b99.JPG

 

IMG_0046.thumb.JPG.0f7cad139442383656fc0bcca1acaabb.JPG

For some weird reason i really do like rigging part of ship building. It is slow, precise process that requires patience, few tweezers and a good glasses :-).

 

Happy modeling..

 

 

Link to comment
Share on other sites

Great work.

 

I am not saying that you should do it but I think Doris has shown in her recent postings of her work with Sculpey clay that after you are done with the carving and baking that you can still make adjustments for fit while the clay is still hot by putting it into place and holding it while it cools.

 

It would probably not make any difference with me anyway. Everything I try to carve ends up looking like an Owl.

Lou

 

Build logs: Colonial sloop Providence 1/48th scale kit bashed from AL Independence

Currant builds:

Constructo Brigantine Sentinel (Union) (On hold)

Minicraft 1/350 Titanic (For the Admiral)

1/350 Heavy Cruiser USS Houston (Resin)

Currant research/scratchbuild:

Schooner USS Lanikai/Hermes

Non ship build log:

1/35th UH-1H Huey

 

Link to comment
Share on other sites

10 hours ago, lmagna said:

Great work.

 

I am not saying that you should do it but I think Doris has shown in her recent postings of her work with Sculpey clay that after you are done with the carving and baking that you can still make adjustments for fit while the clay is still hot by putting it into place and holding it while it cools.

 

It would probably not make any difference with me anyway. Everything I try to carve ends up looking like an Owl.

 

Thanks,

 

I was unable to do anything with sculpey scrolls after baking process, except to sand it...  I might need to do a bit more research on this part.. I will check some postings on forums.

 

Cheers.

 

 

 

 

Link to comment
Share on other sites

I think that Doris is using this stuff: https://pemi.cz/modelit-500-g-bily/p/123438?fc=3167 . I have no idea how it compares to what we call Sculpy but in her build log she clearly shows the process she uses to make the final fitting of her ship stands after doing the baking of the carved forms. 

 

https://modelshipworld.com/uploads/monthly_2019_01/9.jpg.7bfaee729aba62fdf82e7a97720aa8a6.jpg

 

 

Edited by lmagna

Lou

 

Build logs: Colonial sloop Providence 1/48th scale kit bashed from AL Independence

Currant builds:

Constructo Brigantine Sentinel (Union) (On hold)

Minicraft 1/350 Titanic (For the Admiral)

1/350 Heavy Cruiser USS Houston (Resin)

Currant research/scratchbuild:

Schooner USS Lanikai/Hermes

Non ship build log:

1/35th UH-1H Huey

 

Link to comment
Share on other sites

11 hours ago, lmagna said:

I think that Doris is using this stuff: https://pemi.cz/modelit-500-g-bily/p/123438?fc=3167 . I have no idea how it compares to what we call Sculpy but in her build log she clearly shows the process she uses to make the final fitting of her ship stands after doing the baking of the carved forms. 

 

https://modelshipworld.com/uploads/monthly_2019_01/9.jpg.7bfaee729aba62fdf82e7a97720aa8a6.jpg

 

 

Thanks Lou, that was very helpful; i will try to do it again, it might be successful, who knows. I also find few posts by Doris on another forums and some youtube videos...

 

Cheers

 

 

 

 

 

 

 

Link to comment
Share on other sites

I wish I could follow and remember everything she is able to do. Truly a master of the art.

Lou

 

Build logs: Colonial sloop Providence 1/48th scale kit bashed from AL Independence

Currant builds:

Constructo Brigantine Sentinel (Union) (On hold)

Minicraft 1/350 Titanic (For the Admiral)

1/350 Heavy Cruiser USS Houston (Resin)

Currant research/scratchbuild:

Schooner USS Lanikai/Hermes

Non ship build log:

1/35th UH-1H Huey

 

Link to comment
Share on other sites

 

A bit of a work continued today by making a footropes on bowsprit and mast coats.

 

A tan rope, 0.018 in size was used to make a ropes. Seizing was done in my favorite way: wrap the rope (for a seizing) on a needle which diameter is very close to double of the thickness of the rope i will be seizing. Needle was waxed a bit so the seizing can be removed easily. Then i drop of a glue is applied on seizing to freeze it so it can be removed from the needle. The seizing is cut to correct size that fits the requirements.

Both ends of the future footropes are glued so pushing them thru the seizing opening will not be a challenge. After that, few knots were made with a smaller diameter rope and footropes are mounted on the ship. The footropes should be a bit loose and not tightly mounted.

 

 

IMG_0053.thumb.JPG.347a72b3d4b5aa3b6e1745762851d387.JPG

 

IMG_0054.thumb.JPG.94ab0707eb4a30b3a7064caed961c345.JPG

IMG_0055.thumb.JPG.be0e3d5a65a20f8f0dac5d9b1cecd2af.JPG

Then i made a mast coats (or wedges as described in instruction). Practicum suggested to use a wire but i decided to make it out of the wood. Scrap piece of wood, about 1.5mm think was a perfect candidate.

 

IMG_0056.thumb.JPG.5d220dcc643364c39843f83d06481e41.JPG

The center hole matching the diameter of the mast where coats will be located. A little bit of cutting, sanding, more sanding and the correct shape was achieved.

 

IMG_0059.thumb.JPG.9ca2972666416e39b1fc6e2480284ff0.JPG

 

IMG_0060.thumb.JPG.1c6f5012492e70787dfda37307b89f4c.JPG

Testing on a foremast...

 

IMG_0057.thumb.JPG.785d8c1860e42ecec99a5cdbd970ce7a.JPG

IMG_0058.thumb.JPG.0c48ed82d08cf60e2cb8faa886a265be.JPG

And one more was made for main mast...

 

IMG_0061.thumb.JPG.86d464bc34fa74cfae41074e77e0df34.JPG

I decided to keep them in a wood color, so the layer of golden oak was applied.

 

So the masts are almost ready for mounting; ran out of black color so still waiting for an order to arrive... Once in, another layer of flat black will be applied to the top of the masts and they will be ready for mounting..

 

Now the ship starts to get correct size and shape so i have to be more careful and not to break parts that are sticking out and up...

 

Happy modeling.

 

 

 

 

 

 

 

 

Link to comment
Share on other sites

It looks like you did so well that you made Patrick back up and do his over as well. Nice complement on a job well done.

Lou

 

Build logs: Colonial sloop Providence 1/48th scale kit bashed from AL Independence

Currant builds:

Constructo Brigantine Sentinel (Union) (On hold)

Minicraft 1/350 Titanic (For the Admiral)

1/350 Heavy Cruiser USS Houston (Resin)

Currant research/scratchbuild:

Schooner USS Lanikai/Hermes

Non ship build log:

1/35th UH-1H Huey

 

Link to comment
Share on other sites

On 2/1/2019 at 1:08 AM, Overworked724 said:

Mast coats look great. Made me rethink my original metal ones.  Looking good!

I am keeping track of my "want to do it differently" notes during my Sultana journey so i totally understand you.. 🙂

Every time i stumbled upon other' Sultana build logs i have the same moment...

 

Thanks..

 

 

 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...