Jump to content

Recommended Posts

Evening all,   today was  "Wicked Wench day"    under the rear cabin windows are twelve  figures  of the wicked wench,  firstly I painted them on the spru's  enamel  brass color  - then after  drying I added a couple of dark washes  finished off  with highlighting with my dry white brush  work.

 

Just the one pic though.

 

 

OC.

DSC00101.JPG

Share this post


Link to post
Share on other sites

I have come up with a plan  -  with the canons breach ropes,  I think I could get away with  drilling through the sidewalls, then tying a knot in the breach rope and pushing the end through the hole in the wall,  this way the  knot will obscure the apperance of the hoops that would have been there on the real ship.

Think its a plan.

 

OC.

Share this post


Link to post
Share on other sites

Evening all  - more work getting done  - its a busy life as a pirate  "ay mate - weres me rum"    so next step is to build and fit the two canons closest to the cabin bulkhead, reason for these two port and larboard  first  - is so I can then fit the staircases that route down over the top of them.

 

Each canon assembly is built up from the two sides/bottom/barrel  and the wheel blocks, I assembled the assemblies and painted them  - minus the wheel blocks that still need to be fitted and painted.

Here are two pics showing the work on these two so far.

 

OC.

 

DSC00105.JPG

DSC00106.JPG

Share this post


Link to post
Share on other sites

Hi there all,     more progress today with the first two canons,  I  attached the wheel  units, then  found the correct size breeching rope (looks ok in scale)  I attached it to the end of the barrel and applied a small amount of pva,  then I  drilled through the side walls roughly the same thickness as the breech rope,  I  then rubbed some pva into the ends of the rope to stiffen it,  then to seat the canon to the deck - I cut and glued a small piece of wood from decking stock,  it was then just a case of passing the rope ends through the holes in side walls - and glued the canons down.

 

When set I will make the rope sag a bit more then dribble a bit of watered pva into the holes.

 

OC.

DSC00108.JPG

DSC00109.JPG

Share this post


Link to post
Share on other sites

Evening all  -  a bit more progress on the pearl,   First I dribbled some watered pva through the holes on the outside wall, then wahen dry I cut the breech rope ends then touched up the holes,  then I attached one of the stairways.

I then turned my attaention to the other side.

 

Just a few pics.

 

OC.

DSC00126.JPG

DSC00122.JPG

DSC00123.JPG

Share this post


Link to post
Share on other sites
8 hours ago, Kevin said:

nice work, you will have this completed and onto your next build by Christmas this year 

Yep  - next build for the foreseeable  and into the next zillion years will be a  dolls house for the wife, probably finish when Im grey  (Hang on  - I have no hair)😮

 

OC.

Share this post


Link to post
Share on other sites
29 minutes ago, Old Collingwood said:

next build

Take it from a semi expert OC.

 

Doll houses for the spoucial unit need to be taken in small doses with more manly endeavors filling in. They can make ship building look like a short term project! 

Share this post


Link to post
Share on other sites

Good day all,    another good day on the pearl,   I   finished painting and weathering the other staircase, and duly fitted it,   I then turned my attention  to the bow where I fitted the two beakhead  rails,   these were firstly  painted and weathered  - then glued in place.

They have good shape so I am quite pleased with them.

 

A few pics  -  

 

OC.

DSC00128.JPG

DSC00127.JPG

DSC00129.JPG

Share this post


Link to post
Share on other sites
14 minutes ago, lmagna said:

Take it from a semi expert OC.

 

Doll houses for the spoucial unit need to be taken in small doses with more manly endeavors filling in. They can make ship building look like a short term project! 

You wait till I build a garden to go with  it  and build a miniture petrol lawn mower  - I know the admiral will want actual working devices like a vacume cleaner  etc.

 

OC.

Share this post


Link to post
Share on other sites

If she is like mine she will want you RUNNING the vacuum!

 

Dumb question I suppose at this point but do you have any intent on adding the faded red sides along the lower gunports that shows in some of the Pictures of the Pearl?

 

Share this post


Link to post
Share on other sites
52 minutes ago, lmagna said:

If she is like mine she will want you RUNNING the vacuum!

 

Dumb question I suppose at this point but do you have any intent on adding the faded red sides along the lower gunports that shows in some of the Pictures of the Pearl?

 

They were from a different film from what I have molded her on lou,  Im building her according to how she was in the second film released.

In the first film she looked quite different  as she did in the  third and forth film,   she had slightly different feactures including a skeleton metal figurehead  and I think the red band around her waist.

What I might do is go over her with a  cake burner  like they use for  burning the top of  lemon meringue pies.............Only Joking.:dancetl6:

 

OC.

Edited by Old Collingwood

Share this post


Link to post
Share on other sites

That doesn't look much like the kit either! Don't the kit manufactures have ANY respect for "Scale"? But if you blow up the picture you can see that the gundeck band has a slightly red/black color compared to the hull above and below.

 

That being the case I would think you could do what you want. ( red band, red band, red band, red band):D

 

No really, your build your vision and choice. She is really looking good.

Edited by lmagna

Share this post


Link to post
Share on other sites
1 hour ago, lmagna said:

That doesn't look much like the kit either! Don't the kit manufactures have ANY respect for "Scale"? But if you blow up the picture you can see that the gundeck band has a slightly red/black color compared to the hull above and below.

 

That being the case I would think you could do what you want. ( red band, red band, red band, red band):D

 

No really, your build your vision and choice. She is really looking good.

Thank you sincerely lou,      tell you what  - its such a relief to be working on this scale also, makes my 1/100 greyhound feel like a toy.

 

OC.

Share this post


Link to post
Share on other sites

Evening all,   first day back on the pearl after a short break,  I decided to have a go at the masts - I am using the kit plastic ones  but I am strengthening them on the inside with wood dowels cut to size and glued inside,   this makes a very rigid mast.

 

Just the one pic showing one of the masts with the dowels glued inside.

 

OC.

DSC00131.JPG

Share this post


Link to post
Share on other sites

Not really feeling much like building at the moment this time of the year is always rough on us,   but  early this morning the wife had a hypo  with her diabetes  brought on and made worse by us choosing between food or heating  - no guesses what we had to choose.

So my motivation is abit  strained at the moment  and attention on my wife due to her new addional health issue to contend with.

 

Right  - moan over with.

 

OC.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to provide support to our members in their efforts to raise the quality of their model shipcraft.

The Nautical Research Guild puts on ship modeling seminars, yearly conferences, and juried competitions. We publish books on ship modeling techniques as well as our world-renowned quarterly magazine, The Nautical Research Journal, whose pages are full of articles by master ship modelers who show you how they build those exquisite details on their models, and by maritime historians who show you what details to build.

Our Emblem

Modelshipworld - Advancing Ship Modeling through Research
×