Jump to content

HMS Cruiser by Thunder - FINISHED - Caldercraft - 1:64 Scale


Recommended Posts

I have had this kit some time. The last few kits I have completed have been more like scratch builds so, especially with the review by Keith Julier, I thought this would be a nice relaxing quick build. Plan is to build, more or less, straight from the box. The Keith Julier review describes this as a new level of kit with no nasty issues described and everything fitting without any modifications required. So we will see.

 

I was expecting a lot of these to be on here but a search has found very few examples. I also searched for Cruizer which turned up a few other examples. Out of interest there was a completely different class called Cruizer.

 

This is my fourth build from Caldercraft. There was issues with HMS Supply so I am hoping this will be different.

 

Kit has the usual set of caldercraft drawings and parts, I can photograph and post these if anyone is interested.

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

Main bulkhead removed and marked up ready for bulkhead fitting. I was actually getting into position over the drawing for marking on the bearding line, wale position etc. Then you can transfer out across bulkheads for fitting of planks in those positions from the start.

 

_1020190.thumb.JPG.961f5cd7f48eed5ed9f4ff654857b9a7.JPG

Unfortunately difficult to overlay between drawings to do the marking of the wale position. It was at this point I noticed that the drawing shows the keel to be longer and bulkhead positions out of place.

_1020191.thumb.JPG.e92287263e9cf800f7323e4048b23fbc.JPG

This picture shows the discrepancy at the bow. I hope this is not a sign of things to come. I do expect drawings to be accurate after all it is what we take measurements from. This was the issue with the Brig Supply. That model even had discrepancies for the same dimension between each drawing. 

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

27 minutes ago, Thunder said:

I can photograph and post these if anyone is interested.

Please do. It would seem to be a necessary part of any build.

Lou

 

Build logs: Colonial sloop Providence 1/48th scale kit bashed from AL Independence

Currant builds:

Constructo Brigantine Sentinel (Union) (On hold)

Minicraft 1/350 Titanic (For the Admiral)

1/350 Heavy Cruiser USS Houston (Resin)

Currant research/scratchbuild:

Schooner USS Lanikai/Hermes

Non ship build log:

1/35th UH-1H Huey

 

Link to comment
Share on other sites

Hi, as requested photographs of the parts. I have realised that I have probably had this kit for probably 15 years. My wife brought it me after visiting the companies premises and having a tour. At the time Mars had just come out and they were developing Pickle. 

 

_1020215.thumb.JPG.323afbb7aa2c5de9a896dc26bebee01c.JPG

_1020217.thumb.JPG.76a41c5325cc34b332ce4b020d415234.JPG

_1020218.thumb.JPG.5890daad1cfe98d3bd5b15de0bb51208.JPG

_1020220.thumb.JPG.6db43df056fdeec7a2d3833df2ae0466.JPG

 

_1020221.thumb.JPG.d1f6b1e2fd231fcef0ef6556976fa65b.JPG

A few of the parts are not shown as the build has already started.

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

I believe the "Cruizer" kits are similar (if not identical in many regards) to the Snake kit offering of which there are quite a few comprehensive build logs on this site. The only real major differences being the addition of platforms on Snake, use of carronades vs canons and the additional mast.  I believe both of the kits are earlier Caldercraft releases, so I think you may find them a little less refined than later offerings (certainly fewer detailed PE parts).  Good luck getting started.

Cheers,
 
Jason


"Which it will be ready when it is ready!"
 
In the shipyard:

HMS Jason (c.1794: Artois Class 38 gun frigate)

Queen Anne Royal Barge (c.1700)

Finished:

HMS Snake (c.1797: Cruizer Class, ship rigged sloop)

Link to comment
Share on other sites

Good luck with your build. I'm building the kit now and it's been quite enjoyable. I've made some modifications along the way as well to try to get a more historic rendering. 

 

I'll be following along!

Joe Volz

 

 

Current build:

Model Shipways "Benjamin W. Latham"

 

 

Completed  builds on MSW:

Caldercraft HMS "Cruizer   Caldercraft HMBV "Granado"   Model Shipways "Prince De Neufchatel"

 

 

 

 

Link to comment
Share on other sites

Hi Jason and Joe, thanks for dropping in. You can tell my the parts that they are for both ships as I have three mast holes on my false deck! They did try to tell me to buy the Mars or Jalouse when I purchased it but I wanted this as both of them were prizes rather than an English design. Also, her class was the largest ever produced. Those kits had just been released back then.

 

From what I have done so far I think the lit could be improved with little effort. However, as mine is old they may of already done this.

 

Joe, I have taken a good luck at your build. It seems you are not having the same issues as me with the bulkheads at the stern. I am concerned that I have over 'faired' mine but every time I look I think I should of done more. This is the area of the build I am always uncertain about. You will see what I mean in my next update.

 

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

Next step I removed all the bulkheads from the plywood sheet, traced them onto some paper and then used his to check symmetry. Two at the mid position were out. Before modifying the two I checked each in position on the keel section. None fitted, all needed opening out to get them to fit. The two that weren't symmetrical were due to the central slot so these were rectified whilst opening the slot. Neither of these flaws were noted in the Keith Julier build.

 

_1020192.thumb.JPG.de4ac95e299728231f363d0fd0a12450.JPG

Photo shows bulkheads and false deck dry fitted. This allowed me to mark the points of the bearding line. You will also see that I have extended the line of the deck to the edges of the bulkheads and, taken from the now suspect drawings, the height of the bulkheads from the deck position. This seems to show that the bulkhead tabs, above deck level, are too high. However, the drawings do not shore the deck planking so I do not know if this has been accounted for.

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

Now a question. I have never done a vessel with a bearding line like at the bows in this kit. Usually the bulkheads at the bow come down to leave you just enough space to cut the rabbet between the bulkhead and the walnut keel piece. In this kit there is a huge gap between the two. I have done as you would at the stern, i.e. thin the ply bulkhead down so that after planking there is no step between them and the keel. It just feels wrong doing that here._1020196.thumb.JPG.2b559830719679b94eb4e6337dd08767.JPG

_1020197.thumb.JPG.1170eb9b564885bc795f338589a4dfdb.JPG

Bearding /Rabbet shown drawn on.

 

_1020198.thumb.JPG.4c5dd5bd52e8d3ccd76d68319bb9b752.JPG

Bulkheads again dry fitted with edges blackened to make sure I Do not loose the shape when 'trueing'.

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

Fairing of the bulkheads in progress a bow and stern. They were roughly sanded prior to gluing in place.

 

_1020199.thumb.JPG.420707e33b7a342747830f3de327d7dc.JPG

_1020200.thumb.JPG.7d9a419180527956f6e9025c47cb2599.JPG

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

The next question is with the plank termination patterns between first two and to fore of first bulkhead. 

 

terms_LI.thumb.jpg.29afd2a11492188aa547330b087cc35b.jpg

 

Drawing shows planking started but take notice of the plank termination pieces. Surely this will never work.  I shaped to match the bulkheads.

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

Easy bit before moving on. Mast support pieces glued onto the keel. However, glue alone will never hold these so each had two 1mm wood screws used to fit securely.

_1020202.thumb.JPG.69c63edf1fe9a1e850094eb9937a6a56.JPG

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

Bulwark / gun port ply strips in place. I took numerous measurements for this as the instructions say to place at top of bulkhead tabs but mine are at different heights.

 

_1020203.thumb.JPG.da8e5b5aadce60f1173b49bc56c278d8.JPG

The lines show gun port mid position and deck height.

 

_1020204.thumb.JPG.4dcc8cedda40cb00d4f4a4519b4dc2bf.JPG

I had real issues with getting a good curve, I soaked the strips for two hours but they still bent more easily at the gun port positions, I am hoping I can sort this out or they will have to come off again. Before clamping in position I double checked the gun port height by making up one cannon with strips of deck material under the wheels.

 

_1020212.thumb.JPG.70661c20999e8189c4df3ae9621c57db.JPG

 

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

Now I have a real issue that I hope someone can help me with. I have cut out the bulwark capping strips to check the bulwark shape before gluing on the stern section.

 

The stern fascia does not match the plans in shape or size. The bulwark capping do not match the shape and seem to have an strange inward curve just after the last gun port. I could take measurements for the same dimension off two drawings, however, there is 10mm difference between the two. This is the same issue as found on other Caldercraft  models - very frustrating.

 

_1020209.thumb.JPG.cedfd2360dcad478f7d5be530625f025.JPG

 

I am not sure whether to bend in the gun port strips, try to bend the capping strip or replace the rear of it with a new section.

 

_1020205.thumb.JPG.9ab9cf199b693c071c342e06e46f6158.JPG

Capping strips, and subsequently stern fachia dimension  measured from plan.

 

_1020206.thumb.JPG.977be42edf84ed1bea1a50e570d48361.JPG

Supposed same dimension measured from rear.

 

_1020211.thumb.JPG.9c0c320fc4fbffe8c9538537afe9f90f.JPG

Stern Fascia and counter on drawing.

 

_1020210.thumb.JPG.30d669e2bc03f507642f56673ef95f21.JPG

Stern counter in reality giving two awkward small triangles that will require filling to give a landing for the planking.

 

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

Hmmm. Hope you get this sorted out. This is one of Chris Watton's early designs for Caldercraft, and you can certainly see how more modern designs, including Chris's later efforts, have evolved in the direction of creating sturdier substructures.

Chris Coyle
Greer, South Carolina

When you have to shoot, shoot. Don't talk.
- Tuco

Current builds: Brigantine Phoenix, Hawker Hurricane

Link to comment
Share on other sites

Sadly this bring back many memories....I did the triangle solution, don't recall whether it was even possible to achieve what is illustrate in the plans.  Think your approach of working the gun port ply based on the deck position is a very sound approach.  If its any consolation, the Diana kit is just as unintuitive/unhelpfull at the stern counter as well, I made up my own template.  When I was building Snake which was my first build, these are the challenges I put down to my lack of understanding when in reality the kits have just aged.  If it hadn't been for this site, I would never have got past this early stage.

Cheers,
 
Jason


"Which it will be ready when it is ready!"
 
In the shipyard:

HMS Jason (c.1794: Artois Class 38 gun frigate)

Queen Anne Royal Barge (c.1700)

Finished:

HMS Snake (c.1797: Cruizer Class, ship rigged sloop)

Link to comment
Share on other sites

My cap rail was off at the stern as well in a similar manner. I cut it off and scratched a new one from the point where it diverged from the hull. 

 

 

Joe Volz

 

 

Current build:

Model Shipways "Benjamin W. Latham"

 

 

Completed  builds on MSW:

Caldercraft HMS "Cruizer   Caldercraft HMBV "Granado"   Model Shipways "Prince De Neufchatel"

 

 

 

 

Link to comment
Share on other sites

Hi, thanks Jason, Joe, I seem at least to have the same issues as others. I wondered if I was supposed to shape the rear bulkheads more but his would mean taking more of the stern facia and it would be getting very near to the edge of the chase ports.

 

I noticed you have had to pack out the second from last bulkhead. I have just done that as well.

 

These are simple things that they could of put right years ago after all it is a programmed c.n.c. machine that cuts these sheets. It also shows how useless or biased the kit reviews are. This can be damaging to the hobby as a new starter would of took this as an ideal kit judging by the Keith Julier review only to give it up as a bad job. 

 

I have the Diana on my shelf so thanks for the heads up.

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

I have attached the stern Facia followed by the stern counter. Facia has been sanded down to match ply gun port strips.

 

_1020253.thumb.JPG.953b46e7d9e50e48b3095eb630c6abe1.JPG

_1020254.thumb.JPG.0dfa25a1690631924e45e48a28a71531.JPG

_1020255.thumb.JPG.df5f6fc8b05389238795ff1e8e386a89.JPG

_1020256.thumb.JPG.2991fa11261cdedb7fcb7c3b95746bab.JPG

_1020258.thumb.JPG.d9ae6a12929abeb300d5cc769dfa51e9.JPG

_1020259.thumb.JPG.b7cbe936b9f1821ec14c3269e7281bcb.JPG

The triangular corners have been filled and shaped. Done so first planking can terminate up against the filler and second go over it.

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

  • 1 month later...

Once I got her ready for the first planking I put her aside. I new we were going away for Christmas. Just my wife, myself and our two border collies in a little cottage in Norfolk. We stopped near to a beach which has the biggest seal colony in the UK with 2050 seal pups born between Christmas and November.

 

I new it would be quite with just the beaches and a pub within a minutes walk so took the kit with me.

 

_1020333.thumb.JPG.92ab6707e81c2c220309a2e1fdac60f6.JPG

 

So below is the first planking complete.

_1020584.thumb.JPG.0e1ae7d3d219b8b3014877d38d6f490d.JPG

_1020588.thumb.JPG.3971f892029ca3636c3d58c49bf97422.JPG

_1020589.thumb.JPG.d657ad3411b137b67529811f941cc895.JPG

_1020590.thumb.JPG.a79c1cba9d4e381715c0d75e9e7dcb2c.JPG

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

Haven't been here in awhile and missed this one. I'm also building the Cruiser and it's my first Caldercraft kit. I had the same issue with the capping rails so I angle cut them where the deviated from the top of the bulwarks. The sanded the cut edge to fit the rear cut off part of the capping rails better to the top edge. Matched pretty well and sanding the side edges blended it decent enough.  I'm up to doing the deck fittings on mine.

 

The only other issue was with the second layer of hull planking. This English walnut wood really splintered a lot more than the stuff from others I've worked with - mamoli, corel, constructo, and AL. Leaves more of a rough hewn look to it.

 

Have not seen the review from Julier - I have all the period ship handbooks but none have the Cruiser in them. Is the review available somewhere?

 

Your build  is looking great so far and looking forward to following along!

Current builds:  Caldercraft Cruiser, Mantua Astrolabe

Almost Finished: Mamoli Hunter

 

Completed:  AL Swift, Constructo Albatros

Link to comment
Share on other sites

Hi, there were other reviews that he did that did not appear in the books but were published in the Model Boats magazine. You used to be able to view them on their website.

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

Hi B.E.,

 

I have started the second planking now which has highlighted the deficiencies at the bow. There is too much room between the walnut stem and the bow planking termination piece. This has led to a small sliver of the lighter pine showing. I thought I would get away with it but wished I had packed it out now. I created a Rabbet for the bow planking which has made it worse.

 

Another thing evident after the first planking was the lack of bulkheads, it could have done with extras between the 4th and 5th, 5th and 6th,and 7th and 8th. There is nothing at the stern.

 

Kit instructions say to start second planking at the top of the ply gun port strips. However, I always prefer to start at the main wale as I don't like to see planks passing under it. It does make planking harder as you cannot start the tapering process so early but we will see. Always find the wale planks difficult. It would probably be easier to lay them in the anchor stock style but I was feeling too impatient for that. Anyway they will be covered later by the second wale layer.

 

Another reason for not starting at the top is that my ply gun port strips are slightly off. i.e. the Larboard is a tiny fraction higher. hopefully I can correct this later. It must be my vision though as I have done the same with the first wale plank. perhaps due to my right eye being weak due to previous injuries.

 

_1020592.thumb.JPG.3d29e8842384aa2af7b03f5c99d4540e.JPG

_1020593.thumb.JPG.235a51b8fade653fbf4746ec928c22e2.JPG

The planking clamps are simple nylon 'L' shaped pieces cut from the label guides of a Krones high speed labelling machine, with screws normally used for laying model railway track. In awkward places, on the first planking, these screws are small enough to be put straight through the plank. They are identical to the ones used set into the commercially available thumb screw clamps.

 

I also had the aid of a great little USB chargeable battery drill that I had for Christmas. I sent the first back due to the collets being the same size. Wish I kept it as the second one will not hold its charge.

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

Photo below shows the little drill that I have used to predrill all holes before screwing in the planking clamps.

 

_1020601.thumb.JPG.2d64a1191071e3bd7c39c3c5d40809f5.JPG

This has proved great for the intended job but is lacking power for much more. I started the first planking with my usual pin vise but found the ply to be so dense I was really struggling. This little drill made the task so much easier. 

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

Second planking started. I first used the darkest and poorest quality planks for the wale position as these will be covered._1020594.thumb.JPG.5fc5b163fac3b01528b5f2848f6b3b38.JPG

_1020596.thumb.JPG.bde4956c0ae2ded2f902942d7bd2bbdb.JPG

For the planking above the wales I first sorted any planks that were uniform in colour through out their length. I then chose from these the lightest for this section. When I reached the line of gun ports I followed kit instructions which was to use small sections between the gun ports. I was concerned about doing this and my thoughts were confirmed. The small sections tended to go on as small straight sections which lost the shape of the hull. Continued on both sides as whole lengths.

_1020598.thumb.JPG.2e7a34654a739bbe92aa6d3a2ff48d9d.JPG

_1020599.thumb.JPG.c03d6ed011c5ea04ac6b6527203156ab.JPG

I now have a huge concern. These planks were so easy to shape that I never soaked and pre-shaped them. My concern is that the stresses imposed will make the planks spring out once the bulkhead tabs are removed. I am now considering soaking them in situ and then letting them dry before removing the tabs. Would appreciate your thoughts.

Edited by Thunder

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

Nice start.  I don't remember the planking to be too problematic, but some of that may depend on what you are looking to achieve.  Almost certain you won't be able to continue using full width planks going all the way to the keel.  Tapering of planks is needed at the bow and steelers at the stern.  If you will be coppering, then of course you don't need to be as concerned with appearance below the waterline.  I have always tried to use approximate scale length planks which takes a little longer but can be a bit more controllable.

 

Are you using CA or PVA glue?  My preference is for PVA which is more time consuming, but can still proceed at a reasonable pace with smaller lengths once the PVA has achieved a surface tack simply using fingers and rubber bands around the hull.

 

Looking at your pictures, I can't quite tell whether you have cut a rabbet or bearding line at the sternpost.  Once installed, the 2nd layer planking should be flush with the sternpost rather than sitting on top of it so its the same thickness as the rudder.  A rabbet above the keel will also make things easier, but you may be able to shape planks in these areas and get by.  From experience, you may want to work up from the 'garboard' plank above the keel and work upwards so that your planking meets midway down the hull.

 

 

 

 

Cheers,
 
Jason


"Which it will be ready when it is ready!"
 
In the shipyard:

HMS Jason (c.1794: Artois Class 38 gun frigate)

Queen Anne Royal Barge (c.1700)

Finished:

HMS Snake (c.1797: Cruizer Class, ship rigged sloop)

Link to comment
Share on other sites

Hi Jason,

 

The two top planks that give the position of the main wale are untampered as are the planks fitted above the wale. As the wale planks are 3mm instead of 4mm I decided to start my tapering with the plank fitted directly beneath the two fitted at the position of the wale. where the planks are not broken by gun ports or to be hidden by the wales I have started to use scale length planks of approx. 140mm. 

 

I will be fitting the garboard plank next and then dividing up the rest of the hull into sections before planking each section. I tend to use Aliphatic resin as my glue of choice. It is very similar to PVA but dries more quickly, is waterproof and can be mixed with wood dust to make a filler.

 

I have cut a rabbet and have tapered the stern down to 3mm so that once planked it should be the same thickness as the stern post.

 

The second planking has been easy so far as the planks readily bend. So much so that I didn't pre-shape them. My concern now is that when I cut the bulkheads away above the deck level they will spring back to shape as there is nothing holding the gun port strips to the prow. I was considering wetting them and drying with my plank iron so that they readily take the shape of the hull before cutting the tabs away. As a trial I put a plank in place last night without glue, wet it, and then run the hot iron over it till it was dry. This morning it does appear to have taken on a degree of the bend. I suppose I will not really know till I cut them tabs away. 

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

Planking from wale to bulwark capping rail completed. Next to divide the lower hull into sections. This has been done with the use of Ribbands. These are laid at the widest part of the hull at exact distances to match full plank widths. Ribband laid round to bow and stern as naturally a possible.

_1020602.thumb.JPG.a70c78fe7c8146aca6e15c3694d7d998.JPG

The top ribband shows that the planks will be too narrow at the bow. Some drop planks will be needed in this area.

 

_1020603.thumb.JPG.555ef76a9612e19a31e259d19174f307.JPG

The lower section at the stern indicates a few stealers will be required where as the top section will have tapered planks. I am going to have to do some calculations to see if this is practical.

_1020604.thumb.JPG.2c4f1a8b53c88670ea332d60024ef672.JPG

_1020605.thumb.JPG.2c5719994ef1d680828afeeace3f2618.JPG

One think these ribbands did highlight is that bulkhead 8 is slightly too small. You couldn't see it when doing the first planking but obvious now. You can see this by looking at the ribbands to the far right of the above photograph. A good learning here.

The brass screw head you can see is a BA thread pin that is through a nut set into the bulkhead under the planking for final stand mounting.

Edited by Thunder

Current Build(s):

  • H.M.S Diana 1794 - Caldercraft 1:64 Scale

 

Completed Builds:

 

 

 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...