Jump to content

HMS Beagle by frankwil - Mamoli/Dusek - 1/64 - by Frank Williams


Recommended Posts

The first big ship build I've undertaken and have been working on for awhile. This kit is from Dusek and was produced after they took over production from Mamoli after the fire at their factory in Italy. Dusek is in the Czech Republic. From seeing pictures of previous builds of the original kit, it looks as though Dusek changed/improved some of the materials used. The bulkheads and frame are of a different type of plywood, and the keel is now made of walnut. I've recently experienced good customer service from the company's owner Daniel. I had reached out on their website to see if I could get a replacement keel for the one I butchered attempting to carve a rabbet line in, and got a very fast response. Daniel sent me a new frame and the sheet that contained the parts for the keel that I received in about a week. I don't know if this is standard practice for them, but it was nice not to have to buy a whole other kit just to replace the keel. They are now producing a majority of Mamoli's original line of model ships. 

 

Current Build: HMS Beagle 1/64

https://modelshipworld.com/index.php?/topic/19447-hms-beagle-by-frank-williams-mamolidusek-164/&do=findComment&comment=593563

 

Completed Builds: 

Midwest Dinghy

Occre Bounty Longboat

 

Link to comment
Share on other sites

This is the current state of the project. After a few redo's and a fairly steep learning curve, I've decided to do spiling for the planking. I know this is not usually done on a first build, but after reading/watching many tutorials, I've finally gotten my head around the spiling operation and think it's a better way to go on the whole. I've gotten my first spiled plank on the port side under the wale in this pic. I'm kicking myself for not duplicating it for the starboard side before I got it glued on. I'm going to make them in pairs from now on. I am currently using the tape method for spiling, but may switch to the compass method or probably use both. The garboard plank and the one next to it were installed before I had decided to go the spiling route are off now because of the gap where a stealer would be needed. I can make that area much prettier now. And for everyone that feels this is too much for the first planking, I say I want to learn this method and get good at it -  so what better way than to practice. IMG_1827.thumb.jpg.3c198dccddd32110d5cf5a273545f6d1.jpg

Current Build: HMS Beagle 1/64

https://modelshipworld.com/index.php?/topic/19447-hms-beagle-by-frank-williams-mamolidusek-164/&do=findComment&comment=593563

 

Completed Builds: 

Midwest Dinghy

Occre Bounty Longboat

 

Link to comment
Share on other sites

So.... the spiling operation is beyond my patience at this point. Spending 4 or 5 hours making two planks, only to have one of them break while trying to fit it is more heartbreak than I can deal with right now. Maybe someday when I have some more builds under my belt, I'll give it another go, but for now it will be back to tapering the stock planks for me. 

Current Build: HMS Beagle 1/64

https://modelshipworld.com/index.php?/topic/19447-hms-beagle-by-frank-williams-mamolidusek-164/&do=findComment&comment=593563

 

Completed Builds: 

Midwest Dinghy

Occre Bounty Longboat

 

Link to comment
Share on other sites

Hi Frank.

Daniel from Dusek has got a good reputation in my book.

Nice to see a Beagle build.

Are you building to the instructions supplied ?? And has anything not been fitting together as per plans/instructions.

This is the model my Daughter has requested me to build for her in the near future.

Gonna follow along with your build I think I'm in at the front row in the middle.

One of the best planking tutorials is already here on MSW. 

http://modelshipworldforum.com/resources/Framing_and_Planking/plankingprojectbeginners.pdf

All the best. Antony.

Edited by AntonyUK
Link added

Best advice ever given to me."If you don't know ..Just ask.

Completed Mayflower

Completed Fun build Tail boat Tailboat

Completed Build Chinese Junk Chinese Pirate Junk

Completed scratch built Korean Turtle ship 1/32 Turtle ship

Completed Santa Lucia Sicilian Cargo Boat 1/30 scale Santa Lucia

On hold. Bounty Occre 1/45

Completed HMS Victory by DeAgostini modelspace. DeAgostini Victory Cross Section

Completed H.M.S. Victory X section by Coral. HMS Victory cross section

Completed The Black Pearl fun build Black Queen

Completed A large scale Victory cross section 1/36 Victory Cross Section

Link to comment
Share on other sites

Hi Daniel

 

Looks like I'll be following along as am keen to build this (after the Endeavour build which comes after my Perseverance build!!) :P

 

Like Antony my Environmental Scientist daughter has asked that this kit be on my to do list. She has had an interest in the works of Charles Darwin so it makes sense she gets a model of the Beagle.

 

I'm right next to Antony on the front row watching with interest.

 

Cheers............Fernando :cheers:

Current Builds - Colonial Brig Perseverance 1807 by Fernando E - Modellers Shipyard - 1:48 scale

 

Previous Builds - 

S Lucia by Fernando E - Panart - Scale 1:30

Sloop Norfolk 1798 by Fernando E - Modellers Shipyard - Scale 1:36 

 

Link to comment
Share on other sites

Hi Frankwil, nice start to a ship I'm also interested in, I will pull up a chair ifn you don't mind.

Have you have a look at Chucks Planking Videos found under "Building, Framing, Planking and plating a ships hull and deck"

Heres the link https://modelshipworld.com/index.php?/topic/13850-chucks-planking-videos/&do=findComment&comment=428102

Hope this helps

Completed Build --- Virginia 1819 - Artesania Latina

Other Models      --- German Armor plus others    Mastermind

 

Current Build --- Liveship Vivacia

Link to comment
Share on other sites

Antony, in regards to your question about building per instructions - after abandoning the spiling method - I am going strictly by them so far. That may change as I move forward. Everything seems to fit nicely with the exception of the main deck - which I had to file the notches for the bulwarks somewhat to make it fit. Other than that Its gone smoothly. Nice to see there are others who are interested in this ship. I would highly suggest that if you are in the market to buy this kit, that you get one produced by Dusek. From what I've seen of the old version, this one is of a much better quality. Besides, if you were to get the old version, it would by years old and most likely dried out. 

 

I fell in love with this kit -at least a picture of it - 37 years ago. I found it in a Sharper Image catalog of all places, and told myself that I would build it someday. Now that I have the time, it's on. Was just glad that I could still get one. Thanks Daniel Dusek for picking these up from the ashes.

 

Wallace, as to my experience, I'm not a total novice. For what it's worth, I've built two other kits - albeit a dinghy and an 18th century British longboat. I'm still pretty green though.

 

Frank

Edited by frankwil

Current Build: HMS Beagle 1/64

https://modelshipworld.com/index.php?/topic/19447-hms-beagle-by-frank-williams-mamolidusek-164/&do=findComment&comment=593563

 

Completed Builds: 

Midwest Dinghy

Occre Bounty Longboat

 

Link to comment
Share on other sites

I've gotten the first band from lining out the hull planked. In my ultra-focused state during the lining out process, I forgot to take pictures. I'm kicking myself now because it would have been helpful to anyone wanting to know just how to lay it out. My apologies. I followed Chuck Passaro's planking tutorial - http://modelshipworldforum.com/resources/Framing_and_Planking/plankingfan.pdf and used "art tape" to line off the hull. Art tape can be found at any office supply store or Hobby Lobby if you have one. Just make sure your bulkhead edges are clean so the tape will stick sufficiently. The planking went well and with the help of a digital micrometer, every plank hit the corresponding tick mark on the bulkhead. The only thing I was unsure of was how wide to make the plank at the bow.  I ended up just continuing the line from the tick marks for BH 1 & 2 and ended up, for the most part, with a width of around 3 mm at the the bow. Looking at the bow I'm wondering now if I should have gone wider. The inner edges of each plank were sanded down to allow a better fit between planks and eliminate any gaps. There are still some around the bow, so not sure what to do to eliminate that. I just keep telling myself it 1st planking. 

 

I had previously removed the garboard strake and adjacent plank when I was still so confident I was going to be able to do the spiling thing. Wish I hadn't now.

IMG_1863.jpg

IMG_1874.jpg

IMG_1834.jpg

IMG_1830.jpg

Edited by frankwil

Current Build: HMS Beagle 1/64

https://modelshipworld.com/index.php?/topic/19447-hms-beagle-by-frank-williams-mamolidusek-164/&do=findComment&comment=593563

 

Completed Builds: 

Midwest Dinghy

Occre Bounty Longboat

 

Link to comment
Share on other sites

  • 3 weeks later...

First layer of lower planking complete. It went way better than I had feared, though not as smooth as I had hoped. All in all, I'm pleased with it overall. IMG_1876.thumb.jpg.b7bcf1fe6d053bd02ee2075f657bb688.jpgIMG_1890.thumb.jpg.06efe8c955a35fa1a38d25205b4e9f9c.jpg

IMG_1896.thumb.jpg.e096a947ad8c7258ecc915ec3dde2a56.jpg

The garboard plank was made about twice as wide as the 5 mm lathes at it's widest point at Bulkhead 5. I chose to cut this layer of planking back to the bearding line and will run the finish planking to where the rabbet should be.

IMG_1897.thumb.jpg.5125048a83798c63e4667068853dd075.jpgIMG_1895.thumb.jpg.fff77af83d1e711be7c7fa16a1098b99.jpg

I'm not too impressed with the limewood that came with this kit. It was very dry and even splintered after being soaked overnight. I gave up on it after my first band and switched to 1/16" thick basswood. The results were far superior to what I had gotten using the LW. 

 

Stern.thumb.jpg.967e1d9e38c4eadefce27635398852dd.jpg

Not sure what happened at the stern here, but my end result looks nothing like what the plans show. I'm not concerned with it too much for this layer. I can stick some partial planks (stealers?) in the blank spots to even it up. But I am concerned about this repeating itself for the final layer of planking. Anyone with any suggestions?

Inst.thumb.jpg.3d8774447f675bb7c32141c9ab3af4c0.jpg

 

Frank

Edited by frankwil

Current Build: HMS Beagle 1/64

https://modelshipworld.com/index.php?/topic/19447-hms-beagle-by-frank-williams-mamolidusek-164/&do=findComment&comment=593563

 

Completed Builds: 

Midwest Dinghy

Occre Bounty Longboat

 

Link to comment
Share on other sites

Bulwarks installed and finish sanding almost done. Waiting for the peanut butter to dry.  IMG_1938.thumb.jpg.06500acb58b0d311bdfd2908959b782c.jpgIMG_1937.thumb.jpg.6b4012a7fc5e51d802c5f05ac45e639f.jpgIMG_1928.thumb.jpg.cbe05ea43e569777dd1017a66a6140ac.jpg

 

IMG_1930.jpg

Edited by frankwil

Current Build: HMS Beagle 1/64

https://modelshipworld.com/index.php?/topic/19447-hms-beagle-by-frank-williams-mamolidusek-164/&do=findComment&comment=593563

 

Completed Builds: 

Midwest Dinghy

Occre Bounty Longboat

 

Link to comment
Share on other sites

It seems my planking terror and trepidation was for naught. Onward!IMG_1949.thumb.jpg.fee01424478f33853201c1fdb5168b00.jpgIMG_1945.thumb.jpg.9ba924cd2733cc19a12d3baa2174d340.jpg

Current Build: HMS Beagle 1/64

https://modelshipworld.com/index.php?/topic/19447-hms-beagle-by-frank-williams-mamolidusek-164/&do=findComment&comment=593563

 

Completed Builds: 

Midwest Dinghy

Occre Bounty Longboat

 

Link to comment
Share on other sites

Looking splendid  - not normaly up   but thought I should comment on you build.

 

OC.

Current builds  


28mm  Battle of Waterloo   attack on La Haye Saint   Diorama.

1/700  HMS Hood   Flyhawk   with  PE, Resin  and Wood Decking.

 

 

 

Completed works.

 

Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic.

HMS Warspite Academy 1/350 plastic kit and wem parts.

HMS Trafalgar Airfix 1/350 submarine  plastic.

Black Pearl  1/72  Revell   with  pirate crew.

Revell  1/48  Mosquito  B IV

Eduard  1/48  Spitfire IX

ICM    1/48   Seafire Mk.III   Special Conversion

1/48  Kinetic  Sea Harrier  FRS1

Link to comment
Share on other sites

1 minute ago, frankwil said:

Thanks OC.

No problem,  love what you are doing.

 

OC.

Current builds  


28mm  Battle of Waterloo   attack on La Haye Saint   Diorama.

1/700  HMS Hood   Flyhawk   with  PE, Resin  and Wood Decking.

 

 

 

Completed works.

 

Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic.

HMS Warspite Academy 1/350 plastic kit and wem parts.

HMS Trafalgar Airfix 1/350 submarine  plastic.

Black Pearl  1/72  Revell   with  pirate crew.

Revell  1/48  Mosquito  B IV

Eduard  1/48  Spitfire IX

ICM    1/48   Seafire Mk.III   Special Conversion

1/48  Kinetic  Sea Harrier  FRS1

Link to comment
Share on other sites

Planked the stern and underside with tanganyika and walnut respectively.IMG_1953.thumb.jpg.2d44d8e5e2538fd5a8aaad009fdf4df2.jpg

I'm applying a thin coat of very thin mineral oil to keep the walnut and tanganyika from drying out during the build. This oil evaporates after a few days, so I don't have to worry about any adhesive issues popping up. These surfaces will eventually be varnished with a matte finish.

Current Build: HMS Beagle 1/64

https://modelshipworld.com/index.php?/topic/19447-hms-beagle-by-frank-williams-mamolidusek-164/&do=findComment&comment=593563

 

Completed Builds: 

Midwest Dinghy

Occre Bounty Longboat

 

Link to comment
Share on other sites

Pin-striping In Progress

 

Planking of the wales is underway. So far, so good. I also finish planking the bulwarks and used the pencil outline trick to simulate caulking. The only thing is, I outlined all 4 edges on the planks and it looks a little overdone to me. I read later on that outlining should be done on one long and one butt side per plank so as to not have them appear too dark. Oh well, I'll have to live with it because it's not bad enough looking to me to redo it. I'll be removing almost half of them anyway later on to make room for handrails and openings for the cannons.

 

F.

 

IMG_1974.thumb.jpg.5ec6fbade5e8d460fec36526b194009a.jpg

IMG_1982.thumb.jpg.62aa76117f698a6acecca7aeb2fd7231.jpg

 

Current Build: HMS Beagle 1/64

https://modelshipworld.com/index.php?/topic/19447-hms-beagle-by-frank-williams-mamolidusek-164/&do=findComment&comment=593563

 

Completed Builds: 

Midwest Dinghy

Occre Bounty Longboat

 

Link to comment
Share on other sites

Wales completed. Next is to pull down some bulwarks.

 

IMG_2005.thumb.jpg.9a5a13b66181a3bb79bfbfb96d750153.jpg

IMG_2022.thumb.jpg.b633c852002802cbb9660710690f3403.jpg

IMG_2028.thumb.jpg.fd808a050a3f49f4c7ecf30d93be3dc0.jpg

 

Current Build: HMS Beagle 1/64

https://modelshipworld.com/index.php?/topic/19447-hms-beagle-by-frank-williams-mamolidusek-164/&do=findComment&comment=593563

 

Completed Builds: 

Midwest Dinghy

Occre Bounty Longboat

 

Link to comment
Share on other sites

Hi Frank.

Very nice work on the final planking.

Will you be using any paint to cover your planking ?

Following along in the background.

 

Regards Antony.

Best advice ever given to me."If you don't know ..Just ask.

Completed Mayflower

Completed Fun build Tail boat Tailboat

Completed Build Chinese Junk Chinese Pirate Junk

Completed scratch built Korean Turtle ship 1/32 Turtle ship

Completed Santa Lucia Sicilian Cargo Boat 1/30 scale Santa Lucia

On hold. Bounty Occre 1/45

Completed HMS Victory by DeAgostini modelspace. DeAgostini Victory Cross Section

Completed H.M.S. Victory X section by Coral. HMS Victory cross section

Completed The Black Pearl fun build Black Queen

Completed A large scale Victory cross section 1/36 Victory Cross Section

Link to comment
Share on other sites

I jumped the gun on tearing down the bulwark though it's no biggie. I still have final planking below the wales to do

Current Build: HMS Beagle 1/64

https://modelshipworld.com/index.php?/topic/19447-hms-beagle-by-frank-williams-mamolidusek-164/&do=findComment&comment=593563

 

Completed Builds: 

Midwest Dinghy

Occre Bounty Longboat

 

Link to comment
Share on other sites

Antony,

 

I'm sorry I missed the part of your post that asked if I was going to paint the final planking. I know for sure that I will not be painting any of the wales or bulwarks planking. I would prefer to leave the lower planks without paint, but I will have to wait and see how the finished planking turns out. If it's close to the way the first layer turned out, I'll be leaving it "bare" so to speak.

 

Frank

Current Build: HMS Beagle 1/64

https://modelshipworld.com/index.php?/topic/19447-hms-beagle-by-frank-williams-mamolidusek-164/&do=findComment&comment=593563

 

Completed Builds: 

Midwest Dinghy

Occre Bounty Longboat

 

Link to comment
Share on other sites

  • The title was changed to HMS Beagle by frankwil - Mamoli/Dusek - 1/64 - by Frank Williams

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...