Jump to content

How to Taper Masts?


mkmossop

Recommended Posts

The answer may be - it depends! :huh:

 

If you're starting with a square billet of wood, then you can mark the taper out and plane down to the taper first, then when you round your spar the taper is already worked into it.

 

If you're starting with a round dowel then, assuming you don't have a lathe, many people chuck the dowel in a drill press or a hand held electric driss that has been clamped in a fixed place and then use files and sandpaper to taper the rotating dowel.

 

John

Link to comment
Share on other sites

The most reliable way is to taper a square stick, plane it octagonal ('eight-square') then round it with sandpaper strips pulled back and forth around the diameter.

Be sure to sign up for an epic Nelson/Trafalgar project if you would like to see it made into a TV series  http://trafalgar.tv

Link to comment
Share on other sites

Personally, I work with dowel or a piece of square stock and work it down with a miniature plane.  I don't believe there is an advantage in either case, both are very easy to do.  Just remember to take very small amounts of wood off with the plane, it takes time but it's the best way to procede.  It's also important that your plane is razor sharp and adjusted properly before you attempt to taper your mast.  Do sample cuts on a "Test" dowel or or square stock before you tackel the real thing.  Always take your time and remove small amounts of wood and check the diameter often.

 

Tim

Tim 

 

Current Build:

 

 

 

 

 

Future Build:

  • BlueJacket - USS Kidd (Fletcher Class Destroyer) Solid Hull
  • BlueJacket - U.S.S. SAMUEL B. ROBERTS, DE413 | Butler-Class Destroyer Escort
  • BlueJacket - 310' Destroyer "The famous "four-piper" of both World Wars"
  • Model Shipways - Pride of Baltimore II (Topsail Schooner) 
  • Model Shipways - Willie L. Bennett (Chesapeake Bay Skipjack)
  • Constructo - Pilar (Ernest Hemingway's Fishing Yacht)  
  • Sergal - Race Horse (Bomb Ketch)
  • Classic Warships - USS Salem CA-139 (Heavy Cruiser) Resin Kit
  • Pen Duick Schooner - Half Hull (Scratch Build)
  • CSA Submarine Hunley (Resin Kit)
  • Classic Warships - USS Washington BB-56 (Battleship) Resin Kit
  • Blue Ridge Models - USS Alaska CB-1 (Resin Kit)

 

Completed Builds:

                 

Member:

Hampton Roads Ship Model Society

 

              

Link to comment
Share on other sites

You might check another thread here on this forum. http://modelshipworld.com/index.php?/topic/334-my-variation-on-lathe/

Jay

 

Current build Cross Section USS Constitution  http://modelshipworld.com/index.php/topic/10120-cross-section-forward-area-of-the-uss-constitution/

Finished USS Constitution:  http://modelshipworld.com/index.php?/topic/103-uss-constitution-by-modeler12/

 

'A picture is worth a  . . . . .'      More is better . . . .

Link to comment
Share on other sites

Personally, I work with dowel or a piece of square stock and work it down with a miniature plane.  I don't believe there is an advantage in either case, both are very easy to do.  Just remember to take very small amounts of wood off with the plane, it takes time but it's the best way to procede.  It's also important that your plane is razor sharp and adjusted properly before you attempt to taper your mast.  Do sample cuts on a "Test" dowel or or square stock before you tackel the real thing.  Always take your time and remove small amounts of wood and check the diameter often.

 

Tim

 

 

Hmmm... do you rotate the wood along the lathe or move the lathe along the wood?

 

You might check another thread here on this forum. http://modelshipworld.com/index.php?/topic/334-my-variation-on-lathe/

 

Wow cool... I think I'll give this a go first and see how it works... thanks!

Edited by mkmossop
Link to comment
Share on other sites

  • 2 weeks later...

A tool I find handy for tapering is a Stanley knife blade for cutting carpet.It is curved and you can either use as a scraper or as a blade for cutting.

 

Tony

 

 

current build MAYFLOWER

Edited by tony

mayflower

Link to comment
Share on other sites

I did a presentation on masts and spars for the club I belong to.  (Shameless plug for the The Nautical Research and Model Ship Society of Chicago.)  I've attached the presentation.  I use a small lathe made by Harbor Freight Tools, a digital caliper and a file.

 

Hope this helps!

 

 

 

Dan

Masts and Spars.pdf

Link to comment
Share on other sites

For those who work exclusively by hand (or those of us not to be trusted with power tools :)), I included a brief description of some of my tapering methods in my log.

 

http://modelshipworld.com/index.php?/topic/217-bluenose-by-bhermann-model-shipways-2130-164/page-3

 

Check posts #33 and 34 for the details.

 

Bob

Current build -- MS Bluenose

Future build - MS Flying Fish

 

"A ship is safe in harbor, but that's not what ships are for." - William G. T. Shedd

Link to comment
Share on other sites

Bob

 

I am going to try you method on the bowsprit of my Constitution. I do not have a lathe. The bowsprit has some awkward areas to taper and I think the your method will will work out great for me.

Geoff

NRG member #2666
Current build : USS Constitution

 

Finished builds: Armed Virginia Sloop (in gallery)

Link to comment
Share on other sites

I used the dowel-in-drill trick tonight and it worked very well and was quick. I used a rough sandpaper to get it down to size quickly, and then a much finer one to finish it off. It may not be as accurate as some people like, but it did a good enough job for what I want.

Link to comment
Share on other sites

Never had any sucess with either a lathe or plane so I cut the dowel to the required length, mark the with a flet pen dot to the required  finished yard diameter, then mark off the taper profile on the dowel. Rough shape the yard with a small fine file, usually resting the dowel in a small notch on the edge of my bench, file and rotate the dowel slowly to get the profile finishing with various stage sanding with good quality abrasive papers, not cheapy sandpapers. Must have made 30 odd by this method to date its accurate and fast. I check the diameters using a vernier and I can get within 0.2 mm normally or better without much fuss.Considering I have yet to find a concentric dowel.

Norman

 

 

Current build Trumpeter Arizona 1:200 with White Ensign PE and a Nautilus Wooden Deck.

Built Caldercraft Convulsion, HM Brig Badger and HMS Snake.

Awaiting - Zvelda HMS Dreadnought planning to get the Pontos Deck and PE Upgrades, Panart 1:23 Gun deck model and couple of the cannon kits Manatu - French siege mortar, and American coastal cannon.

Link to comment
Share on other sites

Try this

post-246-0-84765400-1363404217.jpg

Jay

 

Current build Cross Section USS Constitution  http://modelshipworld.com/index.php/topic/10120-cross-section-forward-area-of-the-uss-constitution/

Finished USS Constitution:  http://modelshipworld.com/index.php?/topic/103-uss-constitution-by-modeler12/

 

'A picture is worth a  . . . . .'      More is better . . . .

Link to comment
Share on other sites

  • 1 year later...

Interesting discussion, as I was wondering how to give my masts the proper siz since the beginning of my first build. I was planning to buy a lathe, but I do not have any experience with it. I have no idea if they are easy to work with or even what brand is the best buy. Maybe I will try to do it with sanding paper only, although I think it will not give a satisfying result.

Link to comment
Share on other sites

Hi Ken, there are many ways to get the shape, and the least expensive is the sand paper and electric drill method.  You can get the proper shape without a lathe. 

 

The lathe is another method but requires different techniques and some experience.  If you go this route, do some practice to get the feel.  You will also likely use sand paper. 

 

Have fun.                                       Duff

Link to comment
Share on other sites

I use a small lathe but that's partly because i really enjoy wood turning and it gives me an excuse. The main problem is the workpiece pushing off as the dimaeter gets smaller. So I built an adjustable steady which helps. But anything smaller than about 3mm needs mostly sandpaper. To control a taper I divide the taper length into 'portions' then do the same for the diameters (same number of portions). Then turn/sand to the required diameter at the required distance. gets pretty good results, can normally hold to within 0.1mm


 


Nick


Link to comment
Share on other sites

For a better controlled process, build yourself a simple jig. Get 2 paint mixing sticks (for free from Home Depot), cut them to appropriate lengths (slightly longer than the length of your mast) and glue to each on one side a strip of medium grade sand paper.

At one end of such stick glue short piece of wood (spacer) of same thickness as the top of your mast, and at the opposite end glue two other spacers as thick as the bottom diameter of your mast, leaving center hole empty. Glue both sticks together. Especially helpful if you fabricate many identical parts.

 

 

 

Clamp your jig to the worktable.

 

Insert one end of your dowel into a chuck of a handheld drill and place the opposite end of the dowel into this center hole of your jig. Start your drill and gently press it into your jig, until it goes all the way. It will be stopped by the smaller spacer at the other end. Voila!

 

I saw this concept in the Polish shipmodeling forum - one modeler was fabricating a few dozen oars for his model. You can see it here (scroll down the page half way to see appropriate pics).

 

http://www.koga.net.pl/forum/viewtopic.php?f=7&t=44911&p=57251&hilit=galera#p57251

post-6975-0-67684300-1401934297_thumb.jpg

Edited by Dziadeczek
Link to comment
Share on other sites

  • 3 months later...

I use Bob's lathe and file method. I first tried the sandpaper method but found out it would not keep the dowel round as I sanded as material was removed faster in the plain grain areas than the quarter grain areas. The file helped me control that. I used fine sand paper glued to a tounge depresser to finish it off. I did the step-downed section of the tips by hand since the wood is too thin to keep from breaking in the lathe.(Ask me how I know).

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...