Jump to content

Jamie Coleman

  • Content Count

  • Joined

  • Last visited

Everything posted by Jamie Coleman

  1. She’s a beauty. The stern came out very nice after the sanding, gives me hope for when I can finally get back at it.
  2. Almost there! I’ve got to honest, I’m a little bit excited to see what that looks like with all the shields in place, I think it’s going to look spectacular. I like the history lessons that come along with your log as well, adds a little something special.
  3. Something I found on other woodworking projects, try to make one score line very shallow exactly along your straight edge, then go back and make it deeper in stages. Trying to take too big of a bite can cause the knife to wander and look ragged or even move the straight edge.
  4. I’ve been working on deck items recently, and have a lot of them finished. Hatches, steering wheel, binnacle, capstan, galley vent, and a good start on the pump. One thing I did different than the instructions, I was having a bear of a time hollowing out a dowel for the pump “buckets?”, so I used a piece of brass tubing instead, and that worked wonderfully. Need to finish the pump and hang the ship’s bell, then next up are the fife rail and other bitts. Just taking my time on deck fittings, hobbyzone is supposed to be back to work in August, so my building slip should be here soon, if not I’ll next move onto the cannons and carronades.
  5. I've been focusing on the ship's boat, and have completed it. I used some artist's tape as a guide to shaping the hull, to give it a light dip midships. Then laid in the framework, this was some fussy work, no real good way to clamp, so each one was just held in place until it dried enough to let go. The the floor boards and a coat of paint. Gratings, thwarts, cap rail, mast bracketry, splash rail and bowsprit support added next, followed by the winch (carved from a piece of square stock, not perfect, but definitely gives the impression of an octagon). Lastly, the rudder (which is stored inside the boat until needed), oar locks, oars, a few coats of black and white on the hull. So much more detail than the die cast boat from my last project, I'm really happy with the way this turned out.
  6. Works been a little quiet, and I’m working from home, so I’ll make a little progress here and there during coffee breaks. Works out nice for letting glue cure between steps.
  7. I decided to copy a few others and precut the mast holes in the keel, and then I glued a few spacer shims on, so when I glue in the blocks to support the bulkheads, it’ll leave a square for the mast to rest in. I left the spacers extra long to give a little extra support. This seemed like a relatively easy way to get the rake of the masts right, just put the framer right on the plans. I also worked on smoothing up the ship’s boat and attached the keel and stem, applied some wood filler and sanded again. Felt it needed another layer of filler in some spots, so at least one more sanding before I apply some primer.
  8. It does call for them to be installed in the bulkhead former, just not glued in until done fairing. I think I’m going to deviate from the instructions and glue and block first, as you describe. There’s really nothing I can’t sand or shape just because it’s glued up.
  9. Beginner question here, but I’m getting ready to install bulkheads, and the instructions say to fair the bulkheads before glueing them in or installing blocking. I would think the bulkheads are going to be moving around if not glued in and supported, leading to a poor fairing. What would be the reason for that order and what would be downside if I glued them in first?
  10. A little further along, tapered the bulkhead former from the bearding line down to the rabbet strip (mostly chisel work, followed by a light sanding), I added the stem knee, and keel. Keel was ever so slight thicker than the knee, so I took a few shavings off with a block plane. After that all had a chance to dry, I sanded the stem down to accept the figurehead. A bit fussy of a job, but just took it slow until it just fit.
  11. I’m going to follow along, looks like your asking lots of questions, and I’m still pretty new, so even if I can’t help, I’m sure to be interested in the answers too. Just try to stay a step or two in front of me if you can
  12. The kit has arrived! I started with an inventory, and everything looks to have been included. I decided to work on the ship’s boat as well as the main, so I’d have a side project while glue was drying, etc. I started with glueing up the lifts, then started filing and sanding the overall shape. I found a rasp to work very well for the outside shaping, followed by 80 grit. More to come on the boat. In the meantime, dry fit of the bulkheads just to make sure there were no glaring errors, looking fine so far. Nice flat/straight bulkhead former. Followed by soaking the rabbet strip, and letting it dry wrapped around the bulkhead former, then glueing it in place and “clamping” it up with some rubber bands. I did order a hobby zone building slip, and it’s on back-order, so I’ll be slow walking the build just a bit, I’d like to have it before I start glueing on the bulkheads.
  13. Welcome, I think you'll find folks here helpful and encouraging. I just finished my first model, and plenty of people had advice, criticism (helpful) and even praise. It's nice to have other people appreciate the amount of effort that goes into one of these projects.
  14. The different bright colored tunics are going to look fantastic with the shields once they go on. Looking really good!
  15. Your fantastic instructions are the reason I chose the Syren, hoping to live up to the quality of the design.
  16. Glad to have you aboard, hopefully the back orders get cleared up and Model Shipways starts shipping kits.
  17. Thanks, and I do think I’m hooked, next is the Syren, and we’ll see where it goes from there.
  18. I ordered the kit from Model Expo, got a great deal with the Father's Day sale. Unfortunately she's back-ordered for a few weeks, but I hope to be unpacking soon! I'll be using the Syren Model Company blocks and rope, so it should be a good upgrade from my last build where I used cheap square blocks, but that'll be a ways down the road. Edited to add: As I go through the build, I’m going to add links to these chapter headings, so it’s easier to find the appropriate sections: Chapter 1: The bulkhead former, tanner, keel and stem knee Chapter 2: The bulkheads and bulkhead fillers Chapter 3: Framing the gun ports and sweep ports etc., updates to follow as I make progress
  19. Thanks to everyone for the warm welcome and helpful comments, looking forward to sharing the next build. Put the finished shots in a gallery:
  20. Here's the finished shots of my first model. Build log:

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem

Modelshipworld - Advancing Ship Modeling through Research
  • Create New...