Jump to content

DaveBaxt

Members
  • Posts

    542
  • Joined

  • Last visited

2 Followers

About DaveBaxt

  • Birthday 06/27/1953

Profile Information

  • Gender
    Male
  • Location
    Northeast England

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. I think its a good idea but could be wrong, but leaving those parts until the first planking is finished . I wish I had done this with my Endeavour. I ended up with a fair bit of damage to the stem/ cut water. I did it your way on my first model and had no issues. Looking great and I really like what you have done so far. I am assuming you won,t be painting over such beautiful wood and I look forward to see what you do next in regards to treating the second planking. Will you also be fitting any tiles? Best regards Dave
  2. Making progress with compensating for the slope of the aft deck. I made two wedges for under the Capstan base on my Proxxon Milling machine and cut a wedge out of the sides of the skylight
  3. Thank you for that and nice to get some input. There is a good bit of work more than the Amati Bounty but up to now it has been fairly similar but think the extra gear on the deck compared to the Amati Bounty is quite a lot and should keep me busy for sometime. I am currently pondering over whether or not to go with keeping everything on the deck vertical or perpendicularto the deck. I think most of the previous blogs have gone with vertical which is different then the drawings so will need to either fit wedges or cut out material to make a slope. Just trying to figure out the best angle. I will probably go with as near to when she is on the stand. If that makes sense. Hope you get your other work done soon. So you can get back to your Bounty.
  4. That is a 'Blast from the past' I didn't know they still made wooden pegs. I thought every thing was made in plastic these days.Second planking is looking great! Dis you lay the first one at the top and work your way down or by the position of the pegs it looks to be the other way round?
  5. Change of tack here. Instead of following the instructions to continue with the hull fittings I have followed the blog by Dashi and started on the deck fittings. First few fittings went rather well Moving onto the Capstan and although the fittings weren't the best I decided to turn down the ends of the 8 mm Dowel and then cut slots to take the vertical Whelps. This has worked reasonably well Next up is the Binnacle assembly and I can't see any other place other than above the area between the ships wheel and the skylight assembly. I have looked at a few blogs and cannot see such a thing as this and see from some photographs that the compass his housed in a small cuboard and wonder if I should try to make something similar. Here is the drawings of what is supplied be the kit. If there are any Endeavour builders out there some help here would be of value. Thanks
  6. Beautiful looking stern. May I ask did the name come with the kit or did you have to make the letters yourself ?
  7. Brilliant Allan you amaze me we how quickly you research stuff. I always seem to take a wrong turn somewhere and end up off track . Even on here I never seem to get what I need when doing searches but thankfully there is always help from someone such as your good self. So thank you once more. Best regards Dave.
  8. Thank you for searching that out for me Allan. As they say here in the uk . There are many ways to skin a cat. No idea where that saying came from and not very suitable these days . I am truely amazed at how many different ways the period ships are put together. I just wish I were 50 years younger when I started this hobby, so as to give me enough time to learn it all. Best regards Dave
  9. After fitting the new position of the Naval hoods and the holes drilled through there is now sufficient room for the anchor ropes. Anchor lines also fitted and painted.
  10. Sorry I did not catch this earlier as it did not flag up for some reason. Thank you again for searching this out for me. Am I correct in thinking this would be a plank on frame model and this wale would be fitted before the planking was fitted? Great close up diagrams are always the best! I think.Best regards Dave
  11. Just realized I think O have made my first major mistake or perhaps not myself. Looking at the two hawse plates just which I have lined up just under the upper wale. Fortunately as yet I have not drilled the holes out yet. I have checked other blogs and they too have had the same problem and have fiited the naval hoods higher up than what is on the drawing.so I will need to do the same and cut away the upper wale. I am kicking my self for not noticing this earlier as a few people have documented the problem with this build. Hopefully I can sort this without any damage to the hull when removing naval. hoods. After removing the naval hoods and a section of wale you can see from the new position of the pins through the hawse holes that there should be enough clearance for the anchor rope to clear the deck.
  12. Great look there Lyle and and interesting formula. Keep up the excelent work and I look forward to your progress. Well done! perhaps one day I will try a bit more of a weathered look. I definately like yours.
  13. Fitted Rudder pintles and bushes which I found very fiddly.Then I fitted the rudder straps first then temporarily secured the rudder with tape whilst gluing and pinning the longer rudder staps to the hull. Glued Quarter badges using CA glue after paining behind the windows mat black .Started focusing on the anchor linings part no 122 which did not fit. I therefore decided to make new ones with 5mm x 1.5mm Lime strips as can be seen below using double sided tape and extending the strips to enlarge the anchor linings and then shaping them. It will also be necessary to bend the 1.5 mm strips to suit the shape of the hull. Hope this works out ok.
  14. Thank you to every one with some very good answers . I am still in two minds with this and will make an attempt at making some letters in the hope they would be good enough to mount on the stern counter /transom. Best regards Dave
  15. I have noticed that quite a few models in the 1700 have their name across the Transom and wonder if this is accurate for this period or is it just something which modelers like to do . I suppose this gives instant recognition but then again so would mounting a plaque somewhere on the stand or on the glass case itself. What are peoples views on this and what do people prefer. Best regards Dave
×
×
  • Create New...