Search the Community
Showing results for tags 'Willie L Bennett'.
-
Having just finished the Lowell Grand Banks Dory, I find myself not yet ready to begin a model of the schooner I'm meaning to build in my garage. And so I reached for the second of the two kits I bought in April 2020 before a bunch of other weird stuff happened, the Willie L Bennett Chesapeake Bay Skipjack. It was quite a contrast opening this kit compared to the little dory model! I'd been advised that this was a good beginner kit when I first looked into this, and I must have even read a build log or two on it before deciding it was a good choice, but if so I had forgotten that I would be greeted with more or less a pile of lumber upon opening the box. It was a little intimidating and I considered putting the whole thing back away since it seems like a lot to get into when I have other projects coming along. Then I got started anyways. I found a 1/4" plywood cutoff just a bit larger than the size shown in the plan, left over from when I built my kitchen cabinets. It was a little bowed, so I fastened a cutoff bit of 5/8" OSB to the bottom and that flattened it right out. I pricked holes through the mold plan into the plywood and connected the dots instead of cutting out that part of the plan and gluing it down, then set the mold up using the cutouts as bracing. I moved on to the keelson tonight. After gluing the three pieces together and sanding it smooth - the laser cutouts weren't quite square, giving it a sawtooth sort of look on end - I sanded an initial bevel into the outer 1/8" strip on each side. I clamped down a straight edge to scribe a cut line, then figured out I could use the straight edge as a guide for an emery board to sand in the rabbet. The keelson sits a bit oddy in the molds, with the forward end sitting quite proud of the notches and the after end recessing in to the point that it will have to be lifted up to fasten the bottom. The next step is going to be some careful measurements and seeing if I need to modify the mold at all.
- 2 replies
-
- Willie L Bennett
- Model Shipways
-
(and 1 more)
Tagged with:
-
Hello all. Long time lurker who's not posted much until recently. I've built a few model boats/ships. I got started modeling in HO. Had one particularly lovely 1910's NH&NYRR layout many years ago. That's what got me scratchbuilding scale bits of the world. I've built a few metal car kits (the old Hubley kits), and a few aircraft (I'm also a pilot and owned a 1946 Aeronca Chief until some years ago). But I've always loved boats as well, and have owned a fair few of those also (almost all sailboats). I just think the alchemy of function and beautiful line makes for some of the most aesthetically pleasing forms ever made by men. I've built exclusively from kits so far. And I prefer working boats over naval ships, although my very first ship model was a Halifax brig. Anyway, I'm in the middle of building the Willie Bennett. I've posted about it asking for help with colors in particular; but I thought I'd go ahead and post a build log. Not that I think much in it will be new or that impressive. But I've learned a lot from reading other logs over the years, and it only seemed fair to participate. If I think of any particular problem I worked through that might be generally illuminating, I'll be sure to mention it. But, like I said, I wouldn't get my hopes up. 🙂 I'll take a few days to put together a few posts that will bring the log up to date. Not much to belabor with the early parts of the build, since they've been done so often. I'm finishing the houses and hatches at the moment, and about to start on the other deck furniture. I'm still working, so progress is not rapid. But I manage to get a little work done on things most days. To start: Building board, keel (with rabbet). Planking goes fast when the planks are this wide! Transom. Bottom planked and shaping the front blocks. Off the build frames and right side up!
-
Hello all, This is my first build log and my first build of a somewhat detailed wooden model boat. I retired about 18 months ago and decided to get into building model boats. I am partial to work boats, especially those of the Chesapeake Bay, so I built a simple crabbing skiff and a smaller scale skipjack wood model to get into it a bit. This kit is far and away more difficult. I am having fun though and the hours just slip on by. I am sorry I did not start the build log properly by documenting the kit unboxing and early stages of my build so this log picks up after I finished the basic hull. I started this build on Jan 15, 2013. I am building the boat as close to the "real thing" as I can and adding as much extra detail as I am capable of. Comments or questions are welcome of course. The cabins and hatches are just temporarily placed on the deck. The main cabin roof was split in two so that I can remove half to see the detail. The cabin windows are clear plastic. The cabin mattresses are pieces of cardboard covered with old sail cloth. All doors are hinged and hatch covers are removable. Well that brings this build up to date. The next task is to cut and install the planksheers.
- 135 replies
-
- willie l bennett
- model shipways
-
(and 1 more)
Tagged with:
-
Hi all! Well finally decided to try and start this kit. Not really a ship modeler, but would love to learn. I am currently working on the build "Moulds" and getting up the courage to tackle the RABBET CUT. My question is: Should the cut be made before I assemble the keel? Meaning, Stern post, AFT SKEG, SKEG BATTEN and other sub assemblies are attached to the Keelson? All help greatly appreciated.
-
For my third build I've decided to resurrect the kit I started about 3 years ago, but gave up on because I found the plan sheets so cluttered and confusing that frustration took the fun out of the build. So after completing the basic hull structure on the inverted skeleton I packed the entire boat up in the box and went on to do Chuck's 18th Longboat and the AL Marie Jeanne instead. Now that I have several excellent Willie Bennett build logs to use as references, I've decided to give it another try. I've wanted to build a Skipjack model after taking my granddaughter to the Chesapeake Maritime Musuem on St Michaels MD several years back and seeing several examples of these fine Chesapeake Bay work boats. First the box with contents and ship's plans (if you enlarge the photos - last 3 photos below - you'll see what I mean by cluttered). This is where I left the model when I decided to suspend the build This is the status so far. Since the below decks structure will be completely covered I chose to not spend a lot of time detailing it and instead installed just enough to strengthen the model. This kit has a tendency to paint one into a corner if not careful. Installing the centerboard was a bit tricky and drilling the holes for the pivot was even more tricky given the side to side clearance and the length of the drill bit. I had to hold the bit in my fingers and rotate it slowing without the aid of a chuck. And, yes, a few of the deck planks are skewed and not completely perpendicular. I cut the notches in the clamp plank off the model after bending to shape using Chuck's hairdryer heat method and letting the planks sit clamped for about 36 hours. In some instances I am using butt joints and in others I'm notching the ends to fit into the pre-cut notches in the clamp plank. ("Clamp" is the term used in the plans) So pull up a barrel, bench, chair, box or whatever and enjoy some popcorn from Sjors popcorn machine (Thanks Sjors ) and join the build.
-
Hello Fellow Shipwrights, I bought the Model Shipways' Willie L. Bennett kit about 6 years ago, but have been intimidated to start. Plus I'm active-duty Navy (Surface Warfare), and have been stationed on ships for the past 3 years. Now that I'm on shore duty (and about 18 months from retiring after 29 years of service), I am making the time to start learning this craft. At any rate, I finally decided to start this thing. I am using the instructions as well as the excellent series of articles written by Kurt Van Dahm (2004, Ships in Scale). After building the build-board, I started working on the keelson assembly but immediately hit a snag. The dimensions of the keelson pieces (it comes in three that are glued together) don't match the drawing near the aft end. Model Expo is sending a new sheet with the laser-cut keelson on it, I'm just hoping it has the correct dimensions. Worst case, I'll just modify the skeg to account for the missing section of the keelson. Has anyone else had this issue? Here is a photo of my build board (I added additional strength members because it felt too flimsy to me, even with the triangle braces on each side). Last question (for now): What is the best way to create the proper camber on the deck? Do people make a jig, eyeball it, use a template, or some other technique?
- 45 replies
-
- model shipways
- willie l bennett
-
(and 1 more)
Tagged with:
-
Greetings All!! This is actually my second undertaking. My first was the Phantom which I will be putting up shortly. This was a Christmas Present from my lovely wife, and as such had to cut ahead in the Ship queue. We start with the traditional unboxing. We begin with the documentation which consists of one manual, a parts manifest, 2 large plan sheets and an errata sheet. The model is kind of a hybrid POF/POB so the contents consist primarily of strip stock, raw brass, and some laser cut sheets as well as various white cast parts which appear at first glance to be of decent quality and useable as is. Finally the normal supply of blocks, string and normal ship fittings. The instructions are not too too bad. It is quite informative with history anecdotes as well as examples of how the real ship is built. The trouble is these are intermingled with instructions on how to build them in the kit and they tend to get muddled at some points. I like the information however, being a novice, I found it confusing at points. To kick off the build a template needs to be attached to a build board which will be used to set up the build molds. I just grabbed an old particle board shelf as the build board and using a glue stick attached the template. I think next time I will use rubber cement to make it semi-permanent because at the moment I am having issues getting the template off of the board - and would like to reuse it as it is a very nice build board =). Once the template is down it is just a matter of attaching the laser cut build molds to the build board using the template as a guide. I added some spars at the base to stabilize the molds and give them some reinforcement. Once all of the molds were in place and proven square it was time to attach the keelson and chine logs. This was very straight-forward, no muss no fuss. The next part is construction of the hull shell itself. The side planks are a single piece of wood cut to follow the chine logs, bent to shape and attached stem and stern. Remember, do NOT glue them to the molds - that would be very very bad. If you should by accident you can carefully pop them off when it is time to separate the shell. *You can, to avoid getting glue stuck to the molds place some wax over them. Once you get the sides in place, time to lay the planks along the bottom of the hull. Again, pretty straight-forward. Cut and place the planks up to the chunk, place the chunks, sand and shape and walla! One Willie Bennett hull shell!! Sand, sand, sand and sand!! I went ahead and primed mine prior to removing it from the molds but there is no requirement to do so, I just wanted to be sure my hull was as finished as possible before flipping it over. Once the shell is complete and removed from the build molds it is decision time!! The next step is the deck framing. There are two ways given to go about it, the first is a basic framing and the second is a "realistic" framing. The main reason to do the second is if you want to build the ship as close to the real thing and/or plan to have it opened up or have some of the interior visible. If the latter is not the case, the basic framing is more than adequate as it just needs to support the decking. I opted to do the realistic framing including the blocking, more so for the experience than anything else. I did not however detail the bunk areas or the internals of the different wells since the ship will be in a display case and not easily accessible to move and scrutinize close enough to see the detail. The next four pics are of the framing, the first pic is actually partial framing prior to deciding which way to go. At that point I could have gone either way. The last three are the framing completed and ready for the plankshears! The BIGGEST tip I can give at this point, regardless of which style you decide to do - make sure you mark and cut the notches in the clamps which hold the deck beams PRIOR to attaching them to the hull. It is doable after they are attached, but much much easier to do after the fact - so I found out =( From here, I had to break. I was working on the plank shears trying the cuts to get a nice curve and well - let us just say I have some more practice needed! I chewed up a fair amount of wood trying to get them right so had to replace the wood. To keep working I did some work on another kit while waiting to be able to pick up the wood at which point will return to the Willie. that will be tomorrow 😃 Thank you for popping in!! And as always - whatever you do, and however you do it... enjoy it!! -Adam
- 97 replies
-
- Willie L Bennett
- SkipJack
-
(and 2 more)
Tagged with:
-
I started this model back in April and have decided to share what I have done, so fa,r for coments and constructive remarks. I choose this model because it would allow me to practice some techniques that I wanted to learn before I return to my Charles Morgan. Also my deceased wife and I enjoyed a wonderful afternoon on on of these marvalous little boats before she passed. In particular this model has a lot of what most would call scaratch-building and there will be ample oppertunities for me to practice "ironwork" and silver soldering. Building board with building moulds. Keel assembly with rabbit Transon added and chin logs
- 113 replies
-
- model shipways
- willie l bennett
-
(and 1 more)
Tagged with:
-
After reading many of the build logs, I have decided to make my second project, and first build log, the Willie Bennett by Model Shipways. My first build was a solid hull so the built up hull of the Willie looked like a logical next step. I did not photograph the kit box and it contents. Sorry about that but there are many such photographs on this website. I will state that the kit contents are very nice and the lazer die cut parts are well done. The Willie build begins by building a simple frame over "moulds". The moulds were laser cut and matched the plans perfectly. Generally, the beginning assembly is relatively easy. I did find, however, that when I added my first stringer that it caused the structure to twist. I tried removing and regluing the stringer but the structure continue to twist. I decided to continue and add the sides hoping if I weighted the structure down when I added the sides it would dry and remove the twist. It worked. Here are some pictures: 1) This is the basic structure. You can see the pattern I made for the sides in the background. 2) Fitting my pattern for the sides. I cut the pattern from construction paper. 3) Gluing the sides in place while weighting the structure. I used sandbags made from sand filled baggies. I learned this trick in my model airplane building days 4) The basic structure is complete.
- 64 replies
-
- willie l bennett
- model shipways
-
(and 1 more)
Tagged with:
-
First, let me say I have already found this forum to be an invaluable resource for both the neophyte ship modeler and the experienced builder. To that I offer a big... THANK YOU ! ...to the owners and administrators of Model Ship World and everyone else who has taken time to share your knowledge, experience, and wisdom on this forum. Thanks Folks! Now on to some business... Although not my first boat build, this is my first wooden sailing craft build. I've been working on a scale model Dodge Runabout (Legend Model Boats) for several months now (see link in my signature). Its coming along nicely but I still wanted to try my hand at a sailing boat. As for experience, I've been into model building in general since I was a kid and have been fooling around with model railroad stuff for nearly 40 years – mostly HO with a smattering of On30. I prefer working with wood and build mostly kits, but do a little scratch building too. In choosing my first sailing craft build, I thought something rather basic might be in order, so after looking over a lot of stuff I decided on the Willie L. Bennett Chesapeake Bay Skipjack by Model Shipways. Why the Bennett? First, Model Shipways and Model Expo seem to have a topnotch reputation in the model ship business. Second, I like the larger scale, the smaller price tag, and it does seem to be a tad less complicated than, oh say, Nelson's Victory or something on that order... So we'll start with the obligatory “the box and what's in it” shots... After unpacking, ran through the parts list – everything looks good there. I retrieved the plans and instruction booklet and will spend the next week or so studying this stuff and getting a little more familiar with the pieces, parts, and process. Should get started on this thing for real in a week or so. Until then...
- 43 replies
-
- Model Shipways
- Skipjack
-
(and 1 more)
Tagged with:
-
This is my first build, I haven't been able to work on it much as of late due to grad school taking up all my time. But I am going to post pictures and some info. Hopefully I'll be able to get a little work on it done here and there, I know I will have many many questions as I progress along. The typical first picture. Getting started with the build. The shape is coming together. Adding the planks. Lots of sanding happened here. First look of the inside. And we are up to date. If anyone sees anything that I might have missed or needs fixing, please don't hesitate to let me know. This is after all my fist build ever. I am always open to criticism and suggestions. I see that I am going to have to do some soldering, I have never done this, and I don't have any of the tools. What do I need to get to do a good job and make my life as easy as possible. -joshukr-
- 23 replies
-
- model shipways
- Willie L Bennett
-
(and 1 more)
Tagged with:
-
While text and drawings show stiffeners added to transom, none of the kit build photos seem to show those pieces in place. Are they for actual strength in the model or for realistic look of interior of transom (which is hidden by the deck)?
-
Built the frame to build the hull around. Build the Keelson, Stern Post, Skeg, and cut out a few other peices to join the Keelson together. This will be slow going since this is my first build and I am taking my time. I really don't want to frustrate myself right out of the gate. Rich
- 17 replies
-
- model shipways
- skipjack
-
(and 2 more)
Tagged with:
About us
Modelshipworld - Advancing Ship Modeling through Research
SSL Secured
Your security is important for us so this Website is SSL-Secured
NRG Mailing Address
Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917
Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)
Helpful Links
About the NRG
If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.
The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.
The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.