Jump to content
wilnatp

Hannah by wilnatp - Amati - Ship in Bottle

Recommended Posts

Started this kit about a year ago and took some photos, but didn't start my log. Life got busy and now I am back at the build and posting my log. 

 

Available from Seagifts

Product Description (Copied from Seagifts) -- Wood model boat kit from Amati. All wooden parts are precut, for more accurate assembling, decks, and keel are photoetched, guns are metal casted. The kit includes: wooden hull, decks, masts, and skylights, glass bottle with wooden cap, cloth sails, and instruction booklet. 
Intermediate Skill Level:
Boat Length: 4-1/4", Height: 3-1/2", Scale 1:300

 

Opening the box...

post-6922-0-04350600-1427493190_thumb.jpg

 

First step is to number each layer of the hull.

post-6922-0-65213600-1427493326_thumb.jpg

 

Then glue them together.

post-6922-0-06685900-1427493330_thumb.jpg

 

post-6922-0-28147800-1427493333_thumb.jpg

 

Sanded the hull, then painted, then sanded some more. At this point, there is the hull and the quarter deck as two separate pieces. 

post-6922-0-18350200-1427493431_thumb.jpg

 

Share this post


Link to post
Share on other sites

Per other builds - especially S. Kahn's - I cut the channel for the keel early on. See page 21 of the blog.

post-6922-0-44488300-1427493799_thumb.jpg

 

(NOTE: I don't recall what I did that got red on the hull here...)

 

Painted the deck back under the hatch areas. 

post-6922-0-95337900-1427493802_thumb.jpg

 

Removed some of the hull decking to fit the quarter deck. Checking fit with the keel as well. 

post-6922-0-49091900-1427493806_thumb.jpg

 

post-6922-0-26286900-1427493810_thumb.jpg

 

Painting the deck fittings prior to removing them from the brass. This was a lot easier with them attached. 

post-6922-0-59153900-1427493813_thumb.jpg

 

Share this post


Link to post
Share on other sites

I painted the deck pieces and then sanded off the paint. This allowed the lines between the "planks" to be filled with paint.

post-6922-0-34418000-1427494186_thumb.jpg

 

First time didn't take, so I had a second go at it. Then I painted the deck grating and glued them to the deck while it was still attached, making holding the small pieces much easier.

post-6922-0-45360200-1427494189_thumb.jpg

 

Glued the quarter deck to the hull. (But cut it off later when upon sizing i noticed that it was a bit too high)

post-6922-0-34113500-1427494293_thumb.jpg

Note the small gap between the bowsprit and the hull. This ends up not being enough - more on that later. 

A view of the fit from the bottom. Again, I later realized that keel slot wasn't deep enough.

post-6922-0-70212300-1427494401_thumb.jpg

 

Now gluing on the first layer of brass decking.

post-6922-0-27309900-1427494454_thumb.jpg 

Edited by wilnatp

Share this post


Link to post
Share on other sites

Painted the hull and the keel together, but not glued. Needed more sanding after this coat. 

post-6922-0-81007800-1427494527_thumb.jpg

 

Also, drilled holes for the stand/base to attach. 

post-6922-0-72051700-1427494532_thumb.jpg

 

Base is assembled and upper deck glued on. 

post-6922-0-48547700-1427494735_thumb.jpg

 

Cannon painted. 

post-6922-0-40447100-1427494763_thumb.jpg

 

Cannon needed to be sanded down (especially on the front wheels) to fit in the gun-ports.

post-6922-0-60168700-1427494766_thumb.jpg

Share this post


Link to post
Share on other sites

Bulkheads were painted while still attached. Now they are removed from and CAREFULLY Bent to shape. The quarterdeck brass is glued on. 

post-6922-0-39040600-1427494939_thumb.jpg

post-6922-0-89356700-1427494942_thumb.jpg

 

Now the quarterdeck is glued on, the bulwarks glued on, and the transom. 

post-6922-0-96329500-1427494945_thumb.jpg

 

Fitting now showed that there wasn't a deep enough keel cut. The keel slot was deepened. Also needed to cut it deeper on the bow section. 

post-6922-0-98350500-1427494948_thumb.jpg

 

Anchors were painted. I painted the cross bar brown as well. 

post-6922-0-51244900-1427494951_thumb.jpg

Share this post


Link to post
Share on other sites

Final details on the deck house. 

post-6922-0-89707000-1427495595_thumb.jpg

 

Attached the deck house and installed the cannon. 

post-6922-0-22419900-1427495599_thumb.jpg

 

Prepared the winch. Used CA to glue thread onto the ends and wrapped the thread. I substituted the kit white thread for black cotton sewing thread. Same diameter but I like the black better. 

post-6922-0-64192700-1427495607_thumb.jpg

post-6922-0-60267500-1427495610_thumb.jpg

 

Next up is attaching the winch to the deck - FORWARD of the mast step. This isn't accurate to the original, but necessary for the mast to be lowered far enough to fit into the bottle. I played around with a few ways of leaving the winch unglued and thus movable so that it could be glued in aft of the mast after insertion, but there wasn't enough slack in the anchor lines. 

 

Keel was glued into place (with a lot less sticking out below the hull). 

 

And then anchors were attached to the catheads.

 

Now you're caught up. I am waiting for Brass Black to arrive in the post so that I can blacken the yards and masts. I don't want to pain them as I am nervous that the coverage will either be too thin or too think and interfere with the raising ceremony. 

 

Share this post


Link to post
Share on other sites

Random question,

 

Anyone have a Amati Hannah kit lying around on their 'to do' list that is never going to get done,  

if so I'll happily take it off your hands!

Share this post


Link to post
Share on other sites

I got the keel glued in (in its deeper slot now) and painted the hull again. Trimming up to the bulwarks and coating the keel.

post-6922-0-17934800-1427945310_thumb.jpg

 

The anchors are to be tied on to the anchor line and then a copper eyebolt attached, the end of which runs into the cathead. I decided to not tie the anchors on. Instead I doubled the line back through the anchor. I attached the eyebolt, I was able to slide the anchor up and down the line to make it as short or as long as needed. This worked well for me to hold the anchor in place and get the slack line to the desired length. I attempted to slip the copper eyebolt up through the cathead and ended up breaking off the cathead. In this photo, the anchor on the right shows the cathead and the eyebolt glued to it. 

post-6922-0-68752400-1427945394_thumb.jpg

 

Once dry, I used CA to reattach the cathead to bulwark.  I also glued the anchor to the bulwark. When this dried, I was able to glue the line to the anchor and then cut it off. The plans show the anchors hanging, but I wanted them to be up as if they were lashed. 

post-6922-0-89002200-1427945437_thumb.jpg

 

Got both hauled up and glued. 

post-6922-0-91057400-1427945513_thumb.jpg

 

Here they are from the end of the bowsprit. 

post-6922-0-44011000-1427945541_thumb.jpg

Share this post


Link to post
Share on other sites

Carl and Mike. Thanks for the support. I am moving on to rigging now. Your build logs have been great resources for me. 

Share this post


Link to post
Share on other sites

Looking good Nathan.  The rigging is the fun part.  The ship really comes alive when the rigging starts coming together.  

Share this post


Link to post
Share on other sites

Hey Nathan, it's looking great.  Are you planning to add sea to the bottle?  If so, consider filing down the bottom of the ship.  That will help you to need less "sea" material, and make it easier to fit the ship through the neck of the bottle.

Share this post


Link to post
Share on other sites

Spent 6 hours last night rigging. Photos will follow in the next couple of days. Still have about 1.5 hrs left in the rigging - needing to add the square sails and shrouds/ratlines. 

 

I am currently debating whether or not to set the course sail and the topsail or just the topsail. I've seen both configurations on this model, but am leaning toward just the topsail so as to provide a bit more viewing of the deck and rigging. 

 

@Mike, I really like the way that your sea turned out and have been going back and forth on adding it. I've decided against it for this build, but have saved a few clear bottles just to practice putting sea into. 

I tried fitting the ship into the bottle without the masts and it was TIGHT. I'll be filing out some of the neck to make the fit a touch easier. 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Recently Browsing   0 members

    No registered users viewing this page.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem

Modelshipworld - Advancing Ship Modeling through Research
×
×
  • Create New...