Jump to content

10th-11th century Byzantine dromon by Louie da fly - FINISHED - 1:50


Recommended Posts

I love Weber's clarinet concerto...but we digress. Why tie yourself in knots carving the oarsmen in one piece when you will be casting them anyway? Thought of casting them in pieces so that, when you assemble them, they can all vary slightly in pose?

Be sure to sign up for an epic Nelson/Trafalgar project if you would like to see it made into a TV series  http://trafalgar.tv

Link to comment
Share on other sites

Here is the oarsman with his arms broken off and his legs started to be shaped.

20190906_172746.thumb.jpg.076f0179210670f0b87e27d7aa19662d.jpg

Legs done, and ready to glue the arms back on. (Sorry about the photo quality.)

20190906_183655.thumb.jpg.5337782cf0b316789255d2271c91b7a3.jpg 20190906_183732.thumb.jpg.d22c62aa1798b4071a8becdffddcb3dd.jpg 20190906_183746.thumb.jpg.3834f6bfe60d5155266919791eb47e13.jpg

I glued the arms on, and checked the new guy against the one I'd already done. Then it became obvious that the new guy's hands were higher up than the old one's, not because I'd glued them on too high but because I'd carved them that way.  20190906_223023.thumb.jpg.8175172bc2da743bf3c4d455b3c95c36.jpg

20190906_223224.thumb.jpg.ad7e8b20cd5e08d4f138fe105c3dccec.jpg

20190906_223128.thumb.jpg.016d2f7bbc54e0bdb4ab09c33a823549.jpg

 

Time to get clever - I sawed off the arms at the shoulders

20190907_110720.thumb.jpg.c8573573df523a11318272b3b5a67ba2.jpg

and re-glued them to be as close as possible to a mirror image of the arms on the other oarsman.

20190907_184514.thumb.jpg.82fe29e366e515f26dd16503ec32d754.jpg 20190907_184544.thumb.jpg.68d51303add0875d87d84eb22b09f492.jpg 20190907_184606.thumb.jpg.2d3dc54077caf5019622b2a5bdc084f7.jpg

A lot of mucking around, but I think I've finally got it right - except that I now have to carve a new right hand - the arm fell on the floor when I sawed it off and the hand split off, never to be seen again . . . sigh.

 

Steven

Link to comment
Share on other sites

Well carved!

Building: 1:64 HMS Revenge (Victory Models plans)

1:64 Cat Esther (17th Century Dutch Merchant Ships)
 

On the building slip: 1:72 French Ironclad Magenta (original shipyard plans)

 

On hold: 1:98 Mantua HMS Victory (kit bash), 1:96 Shipyard HMS Mercury

 

Favorite finished builds:  1:60 Sampang Good Fortune (Amati plans), 1:200 Orel Ironclad Solferino, 1:72 Schooner Hannah (Hahn plans), 1:72 Privateer Prince de Neufchatel (Chapelle plans), Model Shipways Sultana, Heller La Reale, Encore USS Olympia

 

Goal: Become better than I was yesterday

 

"The hardest part is deciding to try." - me

Link to comment
Share on other sites

Nice job (and surgery) Steven, now onto the 'cloning' process :)

 

cheers

 

Pat

If at first you do not suceed, try, and then try again!
Current build: HMCSS Victoria (Scratch)

Next build: HMAS Vampire (3D printed resin, scratch 1:350)

Built:          Battle Station (Scratch) and HM Bark Endeavour 1768 (kit 1:64)

Link to comment
Share on other sites

8 hours ago, yancovitch said:

haha...very nice....i guess using fimo would have been a sacrilege

Not really - I've tried it but it never seems to give the precision and detail I want, and wood stays where you put it, unlike modelling clay. I've used it (well, plasticiene, actually) to work up a rough idea of what I want to do, but I find wood is better for the final model. And anyway, I like carving ☺️

 

Modelling wax is easier to carve than wood but less forgiving if you make a mistake. You can't add a bit of filler to cover it up.

 

I've bought some sculpy but haven't got around to trying it.

 

Steven

Edited by Louie da fly
Link to comment
Share on other sites

Steven, have you given any thought to modelling the leather sleeves on the lower row of oars which prevent ingress of water?

Dick

Current build: 

 Le Gros Ventre 1:48 POF   http://modelshipworld.com/index.php?/topic/564-le-gros-ventre-by-woodrat-scale-1-48-pof-1767-french-exploration-vessel/

 

Past builds:

Mycenaean War Galley by Woodrat - 1:48 - Shell first Plank on Frame:https://modelshipworld.com/topic/33384-mycenaean-war-galley-by-woodrat-148-shell-first-plank-on-frame

Venetian round ship 14th century by Woodrat fully framed - 1:40 scalCompleted

https://modelshipworld.com/index.php?/topic/17991-venetian-round-ship-14th-century-by-woodrat-fully-framed-140-scale

Venetian Carrack or Cocha 1/64 by woodrat   https://modelshipworld.com/index.php?/topic/4915-venetian-carrack-or-cocha-164-by-woodrat        completed

United States Frigate Essex 1:64 POF   http://modelshipworld.com/index.php?/topic/4496-usf-essex-by-woodrat-scale-1-64-fully-framed-from-takakjian-plans/ - completed 

Yenikapi12 by Woodrat - 1/16 scale - a small Byzantine merchant vessel of the 9th century

https://modelshipworld.com/topic/23815-yenikapi12-by-woodrat-116-scale-a-small-byzantine-merchant-vessel-of-the-9th-century-finished/

The Incredible Hulc by Woodrat - an experimental reconstruction of a mediaeval transport

https://modelshipworld.com/topic/25641-the-elusive-hulc-by-woodrat-finished-a-speculative-reconstruction-of-a-mediaeval-merchantman-132-plank-on-frame/

 

 

 

Location: Perth, Western Australia

 

Link to comment
Share on other sites

Yes, Dick. I'm thinking of making them of thin foil (from Easter eggs) as I did with the big banner. They seem to have about the right modulus (I think that's the first time I've ever used that word outside the science classroom!) of stiffness and flexibility, but I'll find out when I try it.

 

Steven

Link to comment
Share on other sites

On 9/6/2019 at 9:48 PM, druxey said:

Thought of casting them in pieces so that, when you assemble them, they can all vary slightly in pose?

No, I hadn't thought of that, but they're fairly constrained by having to hold the oars so the blades will be at the same level as those of the lower bank. On the other hand, I'm thinking of making, say, 5 different figures for each side (10 in all) cast in resin from these two originals, and then give them different details of hair, beard, face etc and re-cast 5 of each so we end up with a bigger mix of people - not unlike the way the Entombed Warriors were made with mass-produced bodies and individual heads. I can paint the tunics and hair different colours (though dark hair will of course predominate) to add to the variety.

 

Still thinking it through . . . 

 

Steven 

Link to comment
Share on other sites

2 hours ago, Louie da fly said:

Still thinking it through . . . 

And me thinking you had it all worked out!

 

I like the way your figurines turned out, will you be using alternative colours like purple and blue for the hair?

 

For the sleeves of your oars, could a toffee wrapper be of any use? Foil backed with paper ...

Carl

"Desperate affairs require desperate measures." Lord Nelson
Search and you might find a log ...

 

Link to comment
Share on other sites

15 hours ago, cog said:

will you be using alternative colours like purple and blue for the hair?

Of course! How could you think otherwise?😉

15 hours ago, cog said:

For the sleeves of your oars, could a toffee wrapper be of any use? Foil backed with paper ...

Not a bad idea, but I think it might be a little too stiff for the job - it could crumple rather than follow the shape I want. The Easter-egg foil seems to have just the right properties for the job - enough stiffness, but still flexible enough to get the shape right.

 

Steven

Edited by Louie da fly
Link to comment
Share on other sites

Finally got some paint that is the colour I wanted to use for the dromon's hull - basically a red ochre, which would be the source of the tint in red paint at the time . I'm using enamel (Humbrol) because I've found that a tiny bit of PVA glue under acrylic paint seems to mess up the finish. This is the first coat.

20190911_183346.thumb.jpg.ad0fdd81b8536d38a338e4cbcf25087f.jpg

20190911_183501.thumb.jpg.71fe92f63f0ca238fbe88417d44d7d98.jpg 20190911_183615.thumb.jpg.48fccb455e5c1d9a4fdc1a1ee405e34c.jpg 20190911_183625.thumb.jpg.da40723b08e28017a30ac2c61bc6da84.jpg

The trim will be yellow ochre, and the bottom will be black (the colour of pitch). Normally Byzantine ships are shown as black all over in contemporary pictures, but the Emperor's ship is shown as red with yellow trim. I haven't decided yet whether to paint the sternpost and "tail" yellow or red. 

 

Once the painting is all done, I can put the lower oars into place and then finish off the deck (I need it open for the time being so I can see where to glue the oars). And then I can put all the deck items in place that I've been holding off from, add the upper oarbenches and the side castles and the awning at the poop, insert the masts etc etc.

 

Steven

 

 

Edited by Louie da fly
Link to comment
Share on other sites

Looking good Steven; your lady of the sea is showing her finery now.

 

cheers

 

Pat

If at first you do not suceed, try, and then try again!
Current build: HMCSS Victoria (Scratch)

Next build: HMAS Vampire (3D printed resin, scratch 1:350)

Built:          Battle Station (Scratch) and HM Bark Endeavour 1768 (kit 1:64)

Link to comment
Share on other sites

The ocre really makes her "pop".  Looks fantastic, Steven.

Mark
"The shipwright is slow, but the wood is patient." - me

Current Build:                                                                                             
Past Builds:
 La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD           Triton Cross-Section   

 NRG Hallf Hull Planking Kit                                                                            HMS Sphinx 1775 - Vanguard Models - 1:64               

 

Non-Ship Model:                                                                                         On hold, maybe forever:           

CH-53 Sikorsky - 1:48 - Revell - Completed                                                   Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)         

         

                                                                                                                                                                                                                                                                                                

Link to comment
Share on other sites

Steven,

  The paint job looks awesome.  Your Dromon is really coming along.  Looking forward to seeing more.

 

This is a very cool build!

Edited by GrandpaPhil

Building: 1:64 HMS Revenge (Victory Models plans)

1:64 Cat Esther (17th Century Dutch Merchant Ships)
 

On the building slip: 1:72 French Ironclad Magenta (original shipyard plans)

 

On hold: 1:98 Mantua HMS Victory (kit bash), 1:96 Shipyard HMS Mercury

 

Favorite finished builds:  1:60 Sampang Good Fortune (Amati plans), 1:200 Orel Ironclad Solferino, 1:72 Schooner Hannah (Hahn plans), 1:72 Privateer Prince de Neufchatel (Chapelle plans), Model Shipways Sultana, Heller La Reale, Encore USS Olympia

 

Goal: Become better than I was yesterday

 

"The hardest part is deciding to try." - me

Link to comment
Share on other sites

Painting the hull below the waterline black to represent pitch. Two coats of enamel - more a charcoal than a pure black, which I think would look wrong.

20190918_191832.thumb.jpg.06a0fe5f2853a754928368453a202492.jpg 20190918_191837.thumb.jpg.6133128adac9c4cbd8d15dfee847969e.jpg 20190918_191843.thumb.jpg.841cb7e56d02c71102376e82ced7f4fd.jpg 20190918_191853.thumb.jpg.507420c763fbe30451c0495b611f1c0b.jpg

It'll take two days for the paint dry properly, then I'll start on the yellow for the wales, "tail" and other trim.

 

Steven

Link to comment
Share on other sites

Thanks Christos. And thanks everybody for the likes. Perhaps if I need to paint another ship to represent pitch I'll try that. Certainly where one is able to discern the colour, ancient and mediaeval Mediterranean ships all seem to have been black with very few exceptions,which I believe indicates they were coated with pitch for waterproofing.

 

Steven

Link to comment
Share on other sites

No problem, Christos. I appreciate the recommendation. I may find it useful in a later build.

 

Steven

Edited by Louie da fly
Link to comment
Share on other sites

Working on the decoration of the xylokastra (wooden castles). I've looked at various examples of Byzantine decoration - from the great church of Hagia Sofia in Istanbul (I took these photos when I was there in 2000)

20190924_160558.thumb.jpg.d3e508244e9b11d464a9c38f24e187a4.jpg 20190924_160602.thumb.jpg.44c37019edc7de26ac562975e78eb61f.jpg 20190924_160606.thumb.jpg.f487118253a3a488715b914d2dfda0d0.jpg 20190924_160616.thumb.jpg.c25424d67047c2921fc9f7e33aae2de4.jpg 20190924_160622.thumb.jpg.c6c219114c88af91971daee51f2c9d17.jpg All very beautiful, but I think just a little too difficult;

 

Instead I took a motif from a staurotheque (relic of the True Cross), plus a bit of the simpler border decoration from Hagia Sofia

20190924_160700.thumb.jpg.582a76be3b2cacd993bbd9eebb4c6f23.jpg

and here's the first xylokastron - because of the colours I started with, I've swopped the colours around a bit;

 

20190924_112836.thumb.jpg.bdd52cb9666b536b31be9cd456ebf513.jpg 20190924_113348.thumb.jpg.fb9496d953ac7310e097b7e4b174d2af.jpg

20190924_114702.thumb.jpg.581fd249637615077f65215ba7e3c91a.jpg 20190924_120457.thumb.jpg.340eb3e5c341f28402fa57f60ef730b7.jpg

20190924_134109.thumb.jpg.417f6d013574f10fac704e5a0dc1de36.jpg

20190924_160355.thumb.jpg.133cbdac48f3ff3bfe104a3a158dd063.jpg20190924_173944.thumb.jpg.e0e6ef81f1c064eb9717bfc6573455ba.jpg

The second one is under way - I have to wait for the paint to dry before I can continue with it.

 

I'm not terribly happy with the precision of the "T" shapes in the border - I'm thinking of getting another, finer paintbrush. Even though the one I have is pretty fine (it's a watercolour "00", with a nice fine point), I seem to keep getting blobs, or going over the line at the most inopportune times, which messes up the pattern. I think the brush is too long - it sort of "flops" just as I'm trying to finalise a shape, and perhaps a shorter brush with the same fine point would be better.  On the other hand, maybe it's just a matter of keeping my hand still. Masking at this level of detail just doesn't seem practical.

 

Steven

 

Edited by Louie da fly
Link to comment
Share on other sites

Get the best quality sable brush for this kind of work, Steven: a Winsor and Newton Series 7 size 00 or even 000 will do it. Another excellent brushmaker is Rosemary & Co. Even with the brush that you are using, the decoration looks really nice.

Be sure to sign up for an epic Nelson/Trafalgar project if you would like to see it made into a TV series  http://trafalgar.tv

Link to comment
Share on other sites

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...