Jump to content
iosto

Cutter Cheerful - 1/4" scale by Losto Doneddu

Recommended Posts

I bought the designs from the site Syren Chuck.
Unfortunately there are no available pieces in laser cut, I proceeded to cut them after pasting paper forms on plywood

post-15132-0-02637700-1433335358_thumb.jpg

Share this post


Link to post
Share on other sites

I preferred to use a construction technique different from that indicated in the instructions.
Typically use this technique for years for the hulls filled.
The technique is to glue the frames and then fill balsa spaces then fill with synthetic filler to have a uniform surface.
in this way laying the boards is very easy, it does not require nailing.
For gluing use then a cyanoacrylate glue

post-15132-0-25109000-1433335657_thumb.jpg

post-15132-0-79435100-1433335660_thumb.jpg

post-15132-0-81617400-1433335663_thumb.jpg

post-15132-0-28192800-1433335668_thumb.jpg

post-15132-0-88313900-1433335671_thumb.jpg

Share this post


Link to post
Share on other sites

At this point I'm starting to think the window and definitive basis.

 

I am undecided whether to create a leg with strips square as models of arsenal, or set it on twooo turned columns with screw pin concealed in a more classical.
Could someone give me suggerimentio designs or realizations of stairs?
or on how to make the columns on the wheel?
so big I never made more than anything I want to find some nice drawings.

Share this post


Link to post
Share on other sites

Riveting bridge
I tried different techniques to see which one was better.
I made several holes with tips 0.5 / 0.6 / 0.8 mm
I inserted the tip of a graphite pencil in the hole and then I put a bit of glue.
then sanded after this is the effect obtained.
The system toothpicks is great but very long and I did not want to use it.

 

post-15132-0-01526000-1449668082_thumb.jpg

Share this post


Link to post
Share on other sites

Test of of burnishing

I had never used this type of burnishing.

From the evidence I've seen that's not good to leave the piece immersed until the burnishing, but it is best to immerse and then take it off after 20-30 seconds, then go left to air and then rub with a woolen cloth.
after the operation must be repeated 8/9 times to get a good coating.

I had a kind of burnishing that works in one dive, it was given many years ago now is ending and I lost the recipe ....

post-15132-0-15060100-1449668390_thumb.jpg

post-15132-0-91497100-1449668392.jpg

Edited by Iosto Doneddu

Share this post


Link to post
Share on other sites

Construction of the anchors
I realized the anchors with the bars and plates of brass.
I have realized a form of wood for the curvature.
I soldered the pieces with tin.
After I finished with the drill Proxxon

post-15132-0-69516300-1449669016_thumb.jpg

post-15132-0-70273500-1449669027_thumb.jpg

post-15132-0-68308500-1449669030_thumb.jpg

post-15132-0-00645600-1449669037_thumb.jpg

post-15132-0-39897400-1449669043_thumb.jpg

post-15132-0-09239200-1449669048.jpg

Share this post


Link to post
Share on other sites

Construction of the base

I wanted to make the base to be set out in the window, in order to have the ship on a slipway site.
I wanted to get an antique effect as some models in museums.

I used a wooden base that I covered, cherry wood, with the grain in the central part oriented to the long side, and on the edges perpendicular.
I added a decoration between the two frames

 

I put the tape to leave free areas for bonding.
The finishing was done with shellac

post-15132-0-56355000-1449669840.jpg

post-15132-0-85636100-1449669849.jpg

post-15132-0-50767200-1449669857.jpg

post-15132-0-82734700-1449669947.jpg

post-15132-0-54662800-1449669960.jpg

Share this post


Link to post
Share on other sites

Thanks Chuck
I could not get a clean job like yours, but I'm very happy.
I thank you for having made available to your experience in this beautiful site that allowed me to learn a lot.
Thanks again

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Recently Browsing   0 members

    No registered users viewing this page.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem

Modelshipworld - Advancing Ship Modeling through Research
×
×
  • Create New...