Jump to content

Armed Launch by mobbsie - FINISHED - Panart - 1/16 - Small


Recommended Posts

Hi Guys,

 

Well here we are, back on familiar ground with a kit build although there is an awful lot on this boat that needs to be scratched. 

 

The Armed Launch was used by different navies during the 19th century, approx. 10 metres in length it was armed with different size guns, one large cannon at the bow and two small swivel guns at the stern.

 

These boats were used for coastal patrols or in escort services, they also demonstrated their wartime capabilities in surprise actions by attacking craft in trouble, anchored up or in the roads. 

 

The model is triple planked with the first planking on full show on the inboard, this planking is Walnut, the second planking is for strength and is Lime, the last planking should be Walnut but I want to change this to Swiss Pear, I want a bare wood finish if possible and I want to keep the paint away from the main parts of the boat.

 

I started with the keel by cutting two 3mm rabbits, I'm not too sure if this was the right thing to do but it's done and so I have to make it work.

 

With the rabbits cut I dry fitted the bulkheads, the top 2/3rds will be removed when the planking is completed, these were then glued into place and the alignment deck put in position, this deck plays no part in the final boat, it's purely to keep the bulkheads square whilst planking.

 

I started the first planking (Walnut) and have so far got just about halfway and so it continues, care has to taken as this first layer is on full show apart from the bow section.

 

I hope all that follow this build will enjoy the trip and please feel free to offer any advice / comments along the way.

 

Some pictures

 

First up the obligatory kit shots 

post-493-0-08113400-1449316406_thumb.jpg  post-493-0-07234100-1449316573_thumb.jpg

 

post-493-0-59118100-1449316528_thumb.jpg

 

The Keel in my clamp showing a Rabbit

post-493-0-83962500-1449316693_thumb.jpg

 

Bulkheads dry fitted

post-493-0-02143700-1449316762_thumb.jpg

 

Bow block attached and alignment deck in place

post-493-0-51733200-1449316817_thumb.jpg

 

The first three rows on both sides

post-493-0-55939200-1449317017_thumb.jpg

 

post-493-0-97097800-1449317086_thumb.jpg

 

Not very exciting at the moment is it.

 

I'm not right upto-date with the pictures but they would only be more of the same planking so that it for now, I will post again when I have more progress, that will be a bit slow due to the time of year and the Admirals just do jobs.

 

Please feel free to make any comments guys.

 

Be Good

 

mobbsie

 

 

mobbsie
All mistakes are deliberate ( me )


Current Build:- HMS Schooner Pickle

 

Completed Builds :-   Panart 1/16 Armed Launch / Pinnace ( Completed ),  Granado Cross Section 1/48

Harwich Bawley, Restoration,  Thames Barge Edme, Repair / Restoration,  Will Everard 1/67 Billings 

HMS Agamemnon 1781 - 1/64 Caldercraft KitHM Brig Badger,  HM Bomb Vessel Granado,
Thames Steam Launch Louise,  Thames Barge Edme,  Viking Dragon Boat


Next Build :-  

Link to comment
Share on other sites

Hello Mobsie,

 

I really enjoyed my time building this one! At this scale there is plenty of scope for attention to the smaller details. In fact you can make anything you like of the model, just let your imagination flow!

 

Good luck!

 

Mike.

Previous Build: LA gun deck cross section.
Previous Build: Lancia Armata. Panart 1:16
Previous Build: HMS Pickle. Jotika Build.

HMS Triton cross section 1:32.

Shelved awaiting improved skills:

Chuck"s Cheerful.

Current build.

Tender Avos.

HM cutter Alert.

 

 

:

Link to comment
Share on other sites

Hi Q A & Mike,

 

Thanks for looking in guys and I think I am going to enjoy building this boat, Mike your absolutely right about letting your imagination run riot.

 

I see Mike that you have suspended your HMS Surprise, have you any ideas when you'll restart her, I've been waiting for Caldercrafts Surprise now for about 3 years, good job I didn't hold my breath.

 

Q A, the first planking is Walnut, I sanded both sides down prior to starting planking just to tidy the wood up, I've never been happy with any Walnut that comes with a kit, it all seems to need quite a bit of work.

 

Be Good

 

mobbsie

mobbsie
All mistakes are deliberate ( me )


Current Build:- HMS Schooner Pickle

 

Completed Builds :-   Panart 1/16 Armed Launch / Pinnace ( Completed ),  Granado Cross Section 1/48

Harwich Bawley, Restoration,  Thames Barge Edme, Repair / Restoration,  Will Everard 1/67 Billings 

HMS Agamemnon 1781 - 1/64 Caldercraft KitHM Brig Badger,  HM Bomb Vessel Granado,
Thames Steam Launch Louise,  Thames Barge Edme,  Viking Dragon Boat


Next Build :-  

Link to comment
Share on other sites

Cracker's, welcome aboard my friend, your not alone with the morning coffee, the day just doesn't start right without it.

 

Be Good

 

mobbsie

mobbsie
All mistakes are deliberate ( me )


Current Build:- HMS Schooner Pickle

 

Completed Builds :-   Panart 1/16 Armed Launch / Pinnace ( Completed ),  Granado Cross Section 1/48

Harwich Bawley, Restoration,  Thames Barge Edme, Repair / Restoration,  Will Everard 1/67 Billings 

HMS Agamemnon 1781 - 1/64 Caldercraft KitHM Brig Badger,  HM Bomb Vessel Granado,
Thames Steam Launch Louise,  Thames Barge Edme,  Viking Dragon Boat


Next Build :-  

Link to comment
Share on other sites

Great to see you starting this log Mobbsie - looks like I'm just in time for a front row seat. As others have said, this is a really nice little kit and fun to build.

Link to comment
Share on other sites

I hope you don't mind if I pull up a chair also.  Looks interesting.

Mark
"The shipwright is slow, but the wood is patient." - me

Current Build:                                                                                             
Past Builds:
 La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD           Triton Cross-Section   

 NRG Hallf Hull Planking Kit                                                                            HMS Sphinx 1775 - Vanguard Models - 1:64               

 

Non-Ship Model:                                                                                         On hold, maybe forever:           

CH-53 Sikorsky - 1:48 - Revell - Completed                                                   Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)         

         

                                                                                                                                                                                                                                                                                                

Link to comment
Share on other sites

I'd like to follow along, too. Gonna hang with Mark, Grant and  the rest of the gang. :)

Ken

Started: MS Bounty Longboat,

On Hold:  Heinkel USS Choctaw paper

Down the road: Shipyard HMC Alert 1/96 paper, Mamoli Constitution Cross, MS USN Picket Boat #1

Scratchbuild: Echo Cross Section

 

Member Nautical Research Guild

Link to comment
Share on other sites

Nice to see you back great protect we seem to running parallel after a big build we are now doing small boats I have started a scratch built set off Diana's boats at 1/48

Ray

 

 Current build A set of HMS Diana`s boats @ 1/48

 HMS Royal Marine a Military class Trawler

 Completed  HMS Diana

Completed build The Lady Nelson

Completed Build HMS Pegasus

Link to comment
Share on other sites

Hi Guys, 

 

Thanks guys, it's an honour to have you sitting in on this project, you are all more than welcome.

 

Bob & John, you know me, I'm not one to let the grass grow beneath my feet, I get bored fairly quickly and need something to do. Having retired 4 years ago if I hadn't got this hobby and forum I would have gone stir crazy by now.

 

Ray, Hi mate, it's strange how some things do work in parallel, I now build small mainly due to a lack of space but there is a lot of detail in some of these boats which pleases me. Still like to hook up for a coffee some time.

 

Hi Ken, Pull up a pew, it's a pleasure to have you along mate, catering trundles by quite often so no need to go hungry, I don't.

 

Grant, You my friend have a lot to answer for, the books been found and is in the cart, most likely my next project. Not a word my friend.

 

Be Good

 

mobbsie

mobbsie
All mistakes are deliberate ( me )


Current Build:- HMS Schooner Pickle

 

Completed Builds :-   Panart 1/16 Armed Launch / Pinnace ( Completed ),  Granado Cross Section 1/48

Harwich Bawley, Restoration,  Thames Barge Edme, Repair / Restoration,  Will Everard 1/67 Billings 

HMS Agamemnon 1781 - 1/64 Caldercraft KitHM Brig Badger,  HM Bomb Vessel Granado,
Thames Steam Launch Louise,  Thames Barge Edme,  Viking Dragon Boat


Next Build :-  

Link to comment
Share on other sites

Interesting little boat.  I may as well join in and watch - - on and off.

 

Cheers,

Piet, The Flying Dutchman.

 

"Your greatest asset is not the quantity of your friends , rather the quality of your friends."  (old Chinese proverb)

 

Current Builds: Hr. Ms. Java 1925-1942

                       VOC Ship Surabaya

 

Planned Builds: Young America Diorama - scale 1:3000

 

Future Builds: KPM ship "MS Musi."  Zuiderzee Botter - scale 1:25. VOC Jacht in a 6" lamp,  Buginese fishing Prauw.  Hr. Ms. Java - Royal Navy Netherlands Cruiser.

 

Completed Builds:   Hr. Ms. O16 Submarine

                             Hr. Ms. O19 - Submarine Royal Navy Netherlands

                             Ship Yard Diorama with Topsail schooner -

                             Friendship Sloop Gwenfra

                           Muscongus Bay Lobster Smack    

                             Golden Hind - Cutte Sark (both not in this forum)

Link to comment
Share on other sites

Glad to have you tag along Piet, drop in any time.

 

Be Good

 

mobbsie

mobbsie
All mistakes are deliberate ( me )


Current Build:- HMS Schooner Pickle

 

Completed Builds :-   Panart 1/16 Armed Launch / Pinnace ( Completed ),  Granado Cross Section 1/48

Harwich Bawley, Restoration,  Thames Barge Edme, Repair / Restoration,  Will Everard 1/67 Billings 

HMS Agamemnon 1781 - 1/64 Caldercraft KitHM Brig Badger,  HM Bomb Vessel Granado,
Thames Steam Launch Louise,  Thames Barge Edme,  Viking Dragon Boat


Next Build :-  

Link to comment
Share on other sites

You've watched so many of my builds that I thought I'd watch you for awhile. 

 

Bob

Every build is a learning experience.

 

Current build:  SS_ Mariefred

 

Completed builds:  US Coast Guard Pequot   Friendship-sloop,  Schooner Lettie-G.-Howard,   Spray,   Grand-Banks-dory

                                                a gaff rigged yawl,  HOGA (YT-146),  Int'l Dragon Class II,   Two Edwardian Launches 

 

In the Gallery:   Catboat,   International-Dragon-Class,   Spray

Link to comment
Share on other sites

Thanks guys for looking in, with all the expertise checking in I've really got to be on my metal, hope I'm worthy.

 

Be Good

 

mobbsie

mobbsie
All mistakes are deliberate ( me )


Current Build:- HMS Schooner Pickle

 

Completed Builds :-   Panart 1/16 Armed Launch / Pinnace ( Completed ),  Granado Cross Section 1/48

Harwich Bawley, Restoration,  Thames Barge Edme, Repair / Restoration,  Will Everard 1/67 Billings 

HMS Agamemnon 1781 - 1/64 Caldercraft KitHM Brig Badger,  HM Bomb Vessel Granado,
Thames Steam Launch Louise,  Thames Barge Edme,  Viking Dragon Boat


Next Build :-  

Link to comment
Share on other sites

  • 2 weeks later...

Mobbsie,

 

I am not sure what will happen with my Surprise. I made a bad error early in the build which has led to major misalignment of the hull. 

That problem coupled with where to keep the monster when finished has stopped my decision making stone dead.

 

Good luck with your armed pinnace.

 

Mike.

Previous Build: LA gun deck cross section.
Previous Build: Lancia Armata. Panart 1:16
Previous Build: HMS Pickle. Jotika Build.

HMS Triton cross section 1:32.

Shelved awaiting improved skills:

Chuck"s Cheerful.

Current build.

Tender Avos.

HM cutter Alert.

 

 

:

Link to comment
Share on other sites

Mobbsie, nice start as I stood up for the first part. lol, now I am sitting with my own cup of joe. Since this is a fairly small hull kit,I would have replaced the stubborn walnut planking with basswood or boxwood. I guess it is a double planked hull?! Looking forward to next episode.

 

Hmm, so it wasn't doubleplanked. I found several builts on youtube, some shorter other longer.

Edited by Nirvana

 

Please, visit our Facebook page!

 

Respectfully

 

Per aka Dr. Per@Therapy for Shipaholics 
593661798_Keepitreal-small.jpg.f8a2526a43b30479d4c1ffcf8b37175a.jpg

Finished: T37, BB Marie Jeanne - located on a shelf in Sweden, 18th Century Longboat, Winchelsea Capstan

Current: America by Constructo, Solö Ruff, USS Syren by MS, Bluenose by MS

Viking funeral: Harley almost a Harvey

Nautical Research Guild Member - 'Taint a hobby if you gotta hurry

Link to comment
Share on other sites

Hi Guys,

 

Mike, Have you discovered what distorted the hull in the first place and if so would it not be possible to un-do and re-do, glue can be undone by using Isopropyl Alcohol for the wood glue and Acetone for C.A., if you could take it back you may be able to straighten it out. It all just depends on how far you've got with her.

 

Per, your right about the boat being short, she's only 59 cm in length but she is triple planked, the first planking is Walnut followed by Lime and then Walnut again for the final planking, I intend to make the final planking Swiss Pear as I don't want to use any paint where I don't need to.

 

At the moment I'm having a nightmare with the first planking, as you say Walnut is pretty stubborn and I'll be honest it's going to look like a dogs dinner. The only saving grace is that a lot of the bad stuff wont be seen, the important planks are above the deck as these will be in full view when the bulkheads are removed, thankfully they are ok.

 

Progress has been slowed somewhat due to the time of year and the up and coming festivities,  plus I've had a few problems that have needed to be sorted out, things like getting my car repaired after a truck took the back end off whilst it was parked up outside my house, then I've had T.V. trouble, my Wi-Fi box packed up, then my viewing card burned out, the end result is that I'm getting it in the neck from the boss to get it all fixed, still nearly there.

 

So please be patient with me and hopefully a pictorial update will come soon I hope.

 

Be Good

 

mobbsie

Edited by mobbsie

mobbsie
All mistakes are deliberate ( me )


Current Build:- HMS Schooner Pickle

 

Completed Builds :-   Panart 1/16 Armed Launch / Pinnace ( Completed ),  Granado Cross Section 1/48

Harwich Bawley, Restoration,  Thames Barge Edme, Repair / Restoration,  Will Everard 1/67 Billings 

HMS Agamemnon 1781 - 1/64 Caldercraft KitHM Brig Badger,  HM Bomb Vessel Granado,
Thames Steam Launch Louise,  Thames Barge Edme,  Viking Dragon Boat


Next Build :-  

Link to comment
Share on other sites

  • 2 weeks later...

Hi Guys,

 

Its been a while since my last post but thankfully the festivities are almost over and I am able to get back into it.

 

All problems are solved on the domestic front, cars fixed, toilets working again, TV's all sorted so the boss is happy again and that makes me a happy chappie.

 

Since my last post the first planking is now done, I didn't post any progress pics mainly because I was so embarrassed with the result, it honestly looked like a real dogs dinner with so many patches and fill-ins, believe me it was a mess. I have filled and sanded down and given a single coat of diluted PVA, so as far as the second planking is concerned and although it's only Lime I will be using it to practice on in readiness for the final planking which will be Swiss Pear.

I am studying Keith Harris's tutorial on planking and am determined to get it right so Wayne, I'm coming your way.

 

 

I was given a link into ebonizing wood by Grant and so am in the process of making up an experimental batch, I want the Sheer Rail to be Ebony and I want it in one piece, but as Ebony is the devil to try and bend and I would be trying to bend a 10mm x 4mm piece, it's not going to happen so an alternative is needed.

 

OK, I have some pics, they are of the completed 1st planking with filler, except for inside the boat which will be in full view once the bulkheads are removed. As I have said guys, apologies for not posting progress shots. 

 

The first two pics are of the inside of the boat which as you can see is looking ok.

 

post-493-0-99870700-1451560200_thumb.jpg

 

post-493-0-45944600-1451560216_thumb.jpg

 

Now we come to the dogs dinner, almost more filler than wood.

 

post-493-0-94821100-1451560229_thumb.jpg

 

post-493-0-62366300-1451560250_thumb.jpg

 

post-493-0-24805700-1451560268_thumb.jpg

 

post-493-0-29050100-1451560284_thumb.jpg

 

So thats it for now, next job is to put a couple of rows of planking at the top and the Garboard planks then take a few measurements, my heads starting to hurt already.

 

Sorry it's not much gents, hopefully it will get better.

 

Be Good

 

mobbsie

 

 

 

mobbsie
All mistakes are deliberate ( me )


Current Build:- HMS Schooner Pickle

 

Completed Builds :-   Panart 1/16 Armed Launch / Pinnace ( Completed ),  Granado Cross Section 1/48

Harwich Bawley, Restoration,  Thames Barge Edme, Repair / Restoration,  Will Everard 1/67 Billings 

HMS Agamemnon 1781 - 1/64 Caldercraft KitHM Brig Badger,  HM Bomb Vessel Granado,
Thames Steam Launch Louise,  Thames Barge Edme,  Viking Dragon Boat


Next Build :-  

Link to comment
Share on other sites

Here you are!!... WELCOME back to the "BRIGHT SIDE"..... nice to see you back here Tony.... will be following along as you progress.Nice choice in your new build.

 

frank

completed build: Delta River Co. Riverboat     HMAT SUPPLY

                        

                         USRC "ALERT"

 

in progress: Red Dragon  (Chinese junk)

                      

Link to comment
Share on other sites

Don't apologise for your planking, it looks fantastic on the inside and the outside will be covered anyhow.

 

You and the family have a very good 2016 and in good health.

 

Cheers,

Piet, The Flying Dutchman.

 

"Your greatest asset is not the quantity of your friends , rather the quality of your friends."  (old Chinese proverb)

 

Current Builds: Hr. Ms. Java 1925-1942

                       VOC Ship Surabaya

 

Planned Builds: Young America Diorama - scale 1:3000

 

Future Builds: KPM ship "MS Musi."  Zuiderzee Botter - scale 1:25. VOC Jacht in a 6" lamp,  Buginese fishing Prauw.  Hr. Ms. Java - Royal Navy Netherlands Cruiser.

 

Completed Builds:   Hr. Ms. O16 Submarine

                             Hr. Ms. O19 - Submarine Royal Navy Netherlands

                             Ship Yard Diorama with Topsail schooner -

                             Friendship Sloop Gwenfra

                           Muscongus Bay Lobster Smack    

                             Golden Hind - Cutte Sark (both not in this forum)

Link to comment
Share on other sites

Yep, gotta agree Mobbsie, the planking looks great where it counts. Looking forward to seeing your next layer go on, and am very interested to read about your ebonising trials.

Link to comment
Share on other sites

Hi Guys,

 

Thanks for your comments and likes gents, very much appreciated.

 

As I have already said in my last post that I was experimenting with an Ebonizing solution and I would like to share my findings.

 

The solution is as easy as breathing to set up, there are two parts which make up the process, firstly there is the Tea, this is a standard tea mix and either loose or tea bags can be used.

 

My made my Tea using 4 x Teabags put into an old coffee jar and hot water from the tap, this was then set aside to brew giving an occasional shake up.

 

The Ebonizer is a solution made from Distilled White Malt Vinegar and fine Wire Wool, place a good quantity of the wire wool into a jar and fill with the Vinegar,  after a couple of hours bubbles start to form within the wire wool, this is the start of the chemical reaction, don't worry it's not explosive and although a gas is produced it's totally harmless. Set the solution to one side and forget for a couple of days.

 

It is possible to speed the process up by removing the wire wool after a couple of days, place some old rags in an old ice cream tub and cover with paper, place the wire wool onto the paper and let it oxidise ( rust ). When a good covering of rust has formed replace the wire wool back into the solution and allow to steep for another five days or until the wire wool has disappeared.

 

Your solution will now have become brown in colour, it is now ready for decanting, using the neck of a plastic bottle, another jar and a coffee filter, place the filter into the top of the plastic bottle and put it into the jar, pour the solution into the filter and allow to drain.

 

Your Ebonizer is now ready to use but it will mature over the next few days. Depending on the amount of Tanning in the wood you want to stain you may have to soak the wood in the tea, if this is the case allow a day for the tea to soak in, remove and allow this to dry. To Ebonize the wood pour the solution into a tub and place the wood into it. The depth of colour depends on what you are after and the time left to soak, a longer soak will result in a darker colour.

 

If you want an aged look to your wood just soak without the tea until you achieve the desired look.

 

It is recommended that all work on the wood be completed before staining as the stain is very much on the surface, I'm now doing a check to see what the penetration is after a few days of soaking.

 

I hope that you can understand the process and that my explanation is clear, if you have any questions please ask.

 

I have a few pictures with my results.

 

The first picture is of the solution after six days, the wire wool has all but disappeared

post-493-0-30796100-1452350011_thumb.jpg

 

Both the Tea and Ebonizer with some examples

post-493-0-63656800-1452350256_thumb.jpg

 

Samples, the three pieces on the left have not been soaked in tea and the Tanning is quite low

Far Left to Right= Lime, Walnut and finally Swiss Pear.

post-493-0-24780000-1452350342_thumb.jpg

 

Second Part, the three samples on the right have been soaked in tea so the Tanning is higher

Far Right to Left= Lime, Walnut and finally Swiss Pear.

post-493-0-24780000-1452350342_thumb.jpg

 

The next picture is Swiss Pear after about a four hour soak, very little penetration.

post-493-0-38631100-1452350767_thumb.jpg

 

So there we are, an alternative to Ebony, some experimentation on your part will be required to meet your needs. The finer the Wire Wool the better it melts and it can be washed in soapy water to remove it's preservatives to also help to speed up the process.

 

I will pass on my result for the long soak when their ready.

 

Give it a go gents, it's safer than using Ebony and you'll be helping safe the planet.

 

Be Good

 

 

mobbsie
All mistakes are deliberate ( me )


Current Build:- HMS Schooner Pickle

 

Completed Builds :-   Panart 1/16 Armed Launch / Pinnace ( Completed ),  Granado Cross Section 1/48

Harwich Bawley, Restoration,  Thames Barge Edme, Repair / Restoration,  Will Everard 1/67 Billings 

HMS Agamemnon 1781 - 1/64 Caldercraft KitHM Brig Badger,  HM Bomb Vessel Granado,
Thames Steam Launch Louise,  Thames Barge Edme,  Viking Dragon Boat


Next Build :-  

Link to comment
Share on other sites

Nice recipe Tony, I've used the tea steel wool and vinegar to weather, but you've taken it to another level. Very good substitute for the Ebony .

 

Frank

completed build: Delta River Co. Riverboat     HMAT SUPPLY

                        

                         USRC "ALERT"

 

in progress: Red Dragon  (Chinese junk)

                      

Link to comment
Share on other sites

Well done mobbsie.  Like Frank, I've used these solutions for weathering.

 

Bob

Every build is a learning experience.

 

Current build:  SS_ Mariefred

 

Completed builds:  US Coast Guard Pequot   Friendship-sloop,  Schooner Lettie-G.-Howard,   Spray,   Grand-Banks-dory

                                                a gaff rigged yawl,  HOGA (YT-146),  Int'l Dragon Class II,   Two Edwardian Launches 

 

In the Gallery:   Catboat,   International-Dragon-Class,   Spray

Link to comment
Share on other sites

Great results Mobbsie. Looks like a very practical and easy to use method.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...