Jump to content

Soldering dangerously close to the hull


Recommended Posts

I need to solder together the deadeye chains on my build, but unfortunately it has to be done in-situ.  Is there a good material to use to keep from melting the hull or scorching the pain work?  I plan to use silver solder and a mini torch.

Henry

 

Laissez le bon temps rouler ! 

 

 

Current Build:  Le Soleil Royal

Completed Build Amerigo Vespucci

Link to comment
Share on other sites

Henry, 

 

Do you have one of those flexible soldering pads.. like this one:  http://www.micromark.com/soldering-pad-6-inches-x-12-inches,7529.html

 

They're flexible and you can cut them with a pair scissors.

Mark
"The shipwright is slow, but the wood is patient." - me

Current Build:                                                                                             
Past Builds:
 La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD           Triton Cross-Section   

 NRG Hallf Hull Planking Kit                                                                            HMS Sphinx 1775 - Vanguard Models - 1:64               

 

Non-Ship Model:                                                                                         On hold, maybe forever:           

CH-53 Sikorsky - 1:48 - Revell - Completed                                                   Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)         

         

                                                                                                                                                                                                                                                                                                

Link to comment
Share on other sites

If you use a torch that close to the hull, PLEASE have a fire extinguisher handy.  I can see needing to form the chains in place, but surely you can remove them to do the soldering.

 

One thing that can work is resistance soldering - a thin insulator between the chain and the hull would be adequate to protect the hull from the heat.  Resistance soldering gets the metal between the electrodes hot extremely quickly and the electrodes act as heat sinks with the power off.

 

My torch is growing cob webs since I started using a resistance soldering unit again.  Had used a home made one 20 years ago but when my buddy moved we flipped and he got to take it with him.  Stay Brite - a silver bearing solder strong enough for chain plates, etc works good with a resistance soldering unit.

 

Kurt

Kurt Van Dahm

Director

NAUTICAL RESEARCH GUILD

www.thenrg.org

SAY NO TO PIRACY. SUPPORT ORIGINAL IDEAS AND MANUFACTURERS

CLUBS

Nautical Research & Model Ship Society of Chicago

Midwest Model Shipwrights

North Shore Deadeyes

The Society of Model Shipwrights

Butch O'Hare - IPMS

Link to comment
Share on other sites

Forget what I said, Henry.   I read what was going on in your build log.  Resistance might be the best way, but you will need a heatsink to protect that plastic hull.

Mark
"The shipwright is slow, but the wood is patient." - me

Current Build:                                                                                             
Past Builds:
 La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD           Triton Cross-Section   

 NRG Hallf Hull Planking Kit                                                                            HMS Sphinx 1775 - Vanguard Models - 1:64               

 

Non-Ship Model:                                                                                         On hold, maybe forever:           

CH-53 Sikorsky - 1:48 - Revell - Completed                                                   Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)         

         

                                                                                                                                                                                                                                                                                                

Link to comment
Share on other sites

I didn't know it was a plastic hull.  I think you need to figure out a way to get the chain parts off the hull.  Supposedly resistance soldering can be done on HO train rail ends with plastic ties w/o damage to the ties but I wouldn't want to take a chance with a plastic hull.

Kurt

Kurt Van Dahm

Director

NAUTICAL RESEARCH GUILD

www.thenrg.org

SAY NO TO PIRACY. SUPPORT ORIGINAL IDEAS AND MANUFACTURERS

CLUBS

Nautical Research & Model Ship Society of Chicago

Midwest Model Shipwrights

North Shore Deadeyes

The Society of Model Shipwrights

Butch O'Hare - IPMS

Link to comment
Share on other sites

Kurt, I have soldered wire to rail with a resistance unit, but I'd be leery of doing it on a plastic hull. If you screw up on the ties, you can hide the boo-boo under the ballast. On the side of a Connie model, well...... Recommend removing it, if you can.

Ken

Started: MS Bounty Longboat,

On Hold:  Heinkel USS Choctaw paper

Down the road: Shipyard HMC Alert 1/96 paper, Mamoli Constitution Cross, MS USN Picket Boat #1

Scratchbuild: Echo Cross Section

 

Member Nautical Research Guild

Link to comment
Share on other sites

I think what I will do is cut the channels from the outside edge into the slots for the deadeyes so that I can swing the entire deadeye and chain assembly down away from the hull.  That will give about 3/4 of an inch clearance from the hull to do the soldering.  I'll put an alligator clamp heat sink on and slide something behind for a heat shield.  Then I can swing the whole assembly back up into the slot and re close the opening in the channel with styrene.

 

Regards,

Henry

 

Laissez le bon temps rouler ! 

 

 

Current Build:  Le Soleil Royal

Completed Build Amerigo Vespucci

Link to comment
Share on other sites

Henry,

 

I do hope you'll test this first using some scrap plastic for hull....  

Mark
"The shipwright is slow, but the wood is patient." - me

Current Build:                                                                                             
Past Builds:
 La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD           Triton Cross-Section   

 NRG Hallf Hull Planking Kit                                                                            HMS Sphinx 1775 - Vanguard Models - 1:64               

 

Non-Ship Model:                                                                                         On hold, maybe forever:           

CH-53 Sikorsky - 1:48 - Revell - Completed                                                   Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)         

         

                                                                                                                                                                                                                                                                                                

Link to comment
Share on other sites

  • 3 weeks later...

Hey guys - you have my interest up regarding the resistance soldering. I have a similar problem like the OP - I need to connect/attach metal parts (brass strip)  around wooden masts. It's mainly 1/16" or 3/32" strip. I have a regular soldering iron and a small torch for hard soldering. I've been nervous about using either in close proximity - maybe 1/8" to 1/4" - to the finished mast for fear of leaving a char mark or burning the paint.

 

Would resistance soldering be an option? If yes, or maybe just in general, what size unit would be good for modeling? I've seen as low powered as 30W to well over 500W.  I have no intention of using this for anything other than scale modeling.  Also is the probe hand piece or the tweezer unit more practical? Could see wanting both but for a first purchase?

Edited by mikiek

Sail on...... Mike         "Dropped a part? Your shoe will always find it before your eyes do"

Current Builds:                                                          Completed Builds:

Lancia Armata 1803 - Panart                                   US Brig Niagara - Model ShipwaysSection Deck Between Gun Bays - Panart  ; Arrow American Gunboat - Amati    

 Riva Aquarama - Amati                                           T24 RC Tugboat  ;  Hispaniola - Megow - Restoration ; Trajta - by Mikiek - Marisstella ; Enterprise 1799 - Constructo                             

                                                                   
                                                               

Link to comment
Share on other sites

  • 1 year later...

Old thread alert!

But I'll repeat something I just mentioned in another soldering thread: soggy globs of toilet paper (umm, use fresh water...) as heat sinks.

 

I soldered a whole mess of brass rails to brass stanchions, pre-situated in drilled holes on a painted plastic deck... with the soldering taking place as close as 1/4 inch from the deck. The soggy blobs did the trick, no damage at all.

 

 

j_8062.JPG

j_8063.JPG

j_8066.JPG

Pat M.

Matthews Model Marine

Model FUNCTION as well as FORM.

Get your boats wet!

Link to comment
Share on other sites

I default to Kurt for all soldering questions.  However, I can say that I've been resistance soldering for a while, specifically on chains, chain plates and other similar items.  I am working in 1:96 so these parts are extremely small.  With resistance soldering, I'm able to make a very convincing chain plate, soldering while a walnut deadeye is already installed.  The deadeye doesn't get charred at all.  I use "Cold Heat".  It uses four AA batteries.  I use Tix or Stay bright with paste flux.  I cut off small slivers of solder and use the flux to hold it in place.  Cold Heat used to be sold by Radio-Shack.  According to their website, ColdHeat.com, it is also sold at Home Depot and Fry's Electronics.  With resistance soldering, it is very important that the parts contact each other.  This is the most difficult part of the operation for me.

 

All the best,

 

Tom

Tom Ruggiero

 

Director Nautical Research Guild

Member Ship Model Society of New Jersey (Past President)

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...