Jump to content
bundybear1981

Longboat HMS Sirius by bundybear1981 - Modellers Shipyard - 1:24 - 1786

Recommended Posts

Good day all!

After an extended hiatus I'm back in the shipyard!  Today I received my next project, the longboat from HMS Sirius, one of the first fleet ships.

 

The box in which she came!

Box.thumb.jpg.a028f17d24bc2a613cb500298952a08d.jpg

 

Next is the contents of the kit spread out.

Contents.thumb.jpg.a699b18c226f4186808a51e05596eec5.jpg

 

First step was to lay out the frames and put the keel in place.  The frames aren't glued to the baseboard so once planked it can be removed from the internals of the longboat, it is there to provide the framework to build on to.  The transom is glued on to the keel however.

Keel_on_frame_-_1.thumb.jpg.bec9fc86c0efebcb0b8a5c3ebe9edb29.jpgKeel_on_frame_-_2.thumb.jpg.268b78ce4b3ec61009af5b5acaf6a95f.jpg

 

Next was to shape the bow blocks with a 45 degree bevel.  To do this I used my rotary tool in the Dremel drill press with a sanding disc on it.  It made the job faster, easier and did a great job!

58c24e106ea35_FillerBevelled-1.thumb.jpg.6680ab5ff7116e1250885fd00d86bcd4.jpg58c24e1a62d2d_FillerBevelled-2.thumb.jpg.d6f6e28ce4101bb155e5fb3f8bc7a630.jpg

 

 

Share this post


Link to post
Share on other sites

Today I started to run the first set of planks.  Firstly the bulkheads 1 through 9 are taped to prevent the glue and planks from binding to it (as mentioned earlier they will be removed later to give the hull its internal shape)

 

WP_20170311_08_01_55_Pro.jpg

 

The bow was too sharp an angle with too little timber for the clamps to grip so a map pin was pushed through.  The bow and stern are glued in place.

WP_20170311_08_01_36_Pro.jpg

 

WP_20170311_08_01_36_Pro.jpg

 

WP_20170310_21_23_54_Pro.jpg

 

 

The next step was to calculate the taper on the 1st run of planks, these run from the first plank 45mm up the bulkhead where the 2nd run begins.  After the angle was calculated the boards were marked for tapering, bundled into groups of 5 planks and sanded on the rotary drill.

WP_20170311_13_26_26_Pro.jpg

Share this post


Link to post
Share on other sites

This is my rotary drill in the drill press the I used to taper the planks before laying them.  It is currently fitted with a sanding disc, this made the shaping of planks fast, easy and accurate.

WP_20170311_16_58_13_Pro.jpg

Next the tapered planks were fitting to the hull,working toward the temporary plank.

WP_20170311_17_02_08_Pro.jpg

 

As I worked toward the centre the clamps became less practical, having planks only glued to each other and not the frame it was much slower so I reverted to map pins to allow more planks to be laid at a time, running a thin bead of glue on the faces of the planks being joined each time.

WP_20170311_17_02_00_Pro.jpg

 

To help with shaping and holding the planks together while the glue dried I got out my forceps clamps and applied light pressure on the planks.

WP_20170311_16_59_00_Pro.jpg

WP_20170311_16_58_46_Pro.jpg

 

Once all the planks are in place I trimmed the overhang planks flush with the transom then any gaps filled with wood filler, holes and marks.

WP_20170312_09_17_41_Pro.jpg

WP_20170312_09_17_33_Pro.jpg

WP_20170312_09_17_15_Pro.jpg

 

This was followed by sanding the planks smooth, removing excess filler and giving a good surface ready for the next stage.

WP_20170314_16_57_28_Pro.jpg

WP_20170314_16_57_19_Pro.jpg

WP_20170314_16_57_12_Pro.jpg

 

After I was satisfied with the sanding job the next step was to fit the washboards strip.  This was 2mm laser cut ply.  It needed to be shaped to follow the curve of the bow.  Using a hand held plank bending tool (incidentally the same tool as in the diagram provided with the model) was quite difficult.  The laser marks for the oar locks cut-outs gave significant weak points while the ply sheet itself was very hard.  It took several attempts to get the shape right, many times re-shaping previously crimped marks.  

 

I would use another method to shape it should I re-visit this build in the future. (as a scratch build)  As a side note the picture showing this process must have been from an earlier version as it wasn't laser cut ply but rather a standard plank marked and shaped.  

 

This was then glued to the 1st plank run that was done.  I used a combination of pins and rubber bands to hold it in place to dry overnight.

WP_20170314_18_00_36_Pro.jpg

 WP_20170314_18_00_27_Pro.jpg

WP_20170314_18_00_17_Pro.jpg
WP_20170314_18_00_05_Pro.jpg

Share this post


Link to post
Share on other sites

Over the last 10 days I've been slowly working on the longboat (however I have been a bit slack on taking progress pictures)

 

The next step was to do the 2nd layer of planking. After the main planking was completed rowlocks were cut out, then a timber strip fitted over the rowlock strip and another one just under it to trim it.

 

Once all the planking was completed it was stained with a teak stain, and a coat of varnish applied (this was later removed with some turps, very wet weather prevent it from properly drying and was still tacky 2 days after application)

WP_20170319_13_49_45_Pro.jpg

 

Next step was to remove the hull from the build frame and remove the bulkheads from the hull.  Thanks to the sticky tape this was easily completed.  Once they were all removed I sanded the inside of the hull, clearing excessive glue and smoothing the inside.  Some marks remained from the plank bender, if I were to redo the model I would use heat to bend the planks so it didn't have the markings from the bends.  

 

Once I was happy with the sanding the inside of the hull was painted white, I applied 3 coats to get a good coverage.

 

Next step was to install the strip below the rowlock inside the hull.  In hindsight this should have been fitted prior to painting (the instructions are out of order here too, they show this being fitted after the painting but later show it painted white with no mention of painting it).  Once this was in place I then cut the timber strip off the rowlocks.  I then filed these with the square needle file to tidy the sides and make sure it was square.

 

After this I proceeded to fit the ribs of the hull.  I drifted from the instructions here a little.  When fitting them I pushed them hard up on the rowlock strip, pushing them out against the hull down to the keel.  I used a sharp cutter to cut them tightly in to place (they were tight enough to remain in place on their own)

WP_20170324_17_07_44_Pro.jpg

 

When I had them all in place I diluted some PVA glue and applied a light coat over the ribs, which then fixed them in place.  The instructions showed each strip (inefficiently) being glued and pinned with map pins to allow the glue to dry.

 

When I worked up to the bow some bulldog clips were used to hold the ribs in place where they bunched at the front.

WP_20170324_18_06_50_Pro.jpg

 

Following the completion of the ribs being placed, the grating that fits under the bench at the transom was fitted in place.  The rear bench was then planked, stained teak and fitted in place.

WP_20170325_17_40_07_Pro.jpg

You'll see two ribs slightly moved in the picture, the glue had not fully dried at this time.  They were placed back in position and clipped in place to fully dry.

 

 

Share this post


Link to post
Share on other sites

Time for the next update!

 

Next I laid the boards inside the hull and the cap rails.

 

WP_20170330_07_44_23_Pro.jpg

 

WP_20170330_07_44_12_Pro.jpg

 

Once the glue had set I cut the row locks in the cap rails and stained them with golden oak stain.  

 

After that I put the benches in then put the supports under them.  Next was to fit the rudder.  I had a materials issue here, the instructions had the same 3x3mm timber that was used for the seat supports for the rudder handle, however there was not enough length left to do so.  The supplied strip was 250mm long.  There was 220mm needed for the bench supports, with the rudder requiring a piece at 10mm and another at 60mm.  To get around this I used one of the spare planks from the first run of planking cut in half and glued together then sanded to 3x3mm.  This was stained teak when it was fitted to the rudder.

 

I then put the rudder brackets on the rudders and fitted the rudder to the transom.

 

WP_20170415_17_04_20_Pro.jpg

 

WP_20170415_17_04_10_Pro%201.jpg

Share this post


Link to post
Share on other sites

Hi Jason. I had the same problem here with the galleon i'm doing. I had to wait for days for the varnish to dry properly. . To start with I thought it was a bad batch but now you've had the same issue it's got to be the humidity. I think i'll be switching to a wax instead of a varnish. She's coming along nicely. Keep those pictures coming.

Matt.:cheers:

Share this post


Link to post
Share on other sites

Around the time cyclone debbie was hiiting far north queensland we were hitting 95 to 99% humidity.  Nothing was drying then! Seems to be a lot better now its dropped off again. 

Share this post


Link to post
Share on other sites

What a gem. Great job.

I have not built a kit from Modelers Shipyard, But I have the Perseverance from them and this will be my next build.

Your construction looks neat tidy and we'll joined. Good work. 

Share this post


Link to post
Share on other sites

thankyou for your kind words Scott.   This is my 3rd build of a Modellers Shipyard (now Modellers Central) kit and I have been happy so far with the quality of their kits.

 

I'm up to a point where I can either finish it and leave it as a row type or continue on to add the rigging.  I plan on doing all the rigging on her.

Share this post


Link to post
Share on other sites

Nice to see that you've got stuck into another one, Jason.  She really looks a treat.

 

John

Share this post


Link to post
Share on other sites

Nice work Jason, the launch is looking good.  I am surprised that with that amount of humidity that the varnish did not start to go "cloudy" on you also.

 

cheers

 

Pat

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Recently Browsing   0 members

    No registered users viewing this page.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem

Modelshipworld - Advancing Ship Modeling through Research
×
×
  • Create New...