Jump to content
ctclock

Meta 484 by ctclock - Billing Boats - flying blind on this one

Recommended Posts

Hello all

 

Here we go :D

 

Welcome to my META 484 by Billing build 

 

Please feel free to comment or add suggestions

 

There is just not much information available out there for the Meta that I can find - I found some photographs of completed models but nothing as far as build logs are concerned. If somebody has a possible source for any detail etc I could check it would be appreciated.

Here are some which I have found: Meta Images and Meta images 2

 

For the time being, I have put the La Toullanaise on hold until I receive the planks and wood I ordered. I was just frustrating myself trying to do something and achieving nothing.

 

So for now - I have decided to start the META 484 from Billing. This is an old kit [would love to know exactly how old] which I bought from a friend a good while ago and its been sitting on my shelf for the best part of 2 years - time to do something about that :D. Fortunately, the kit appears to be complete along with its accessories as well so that's a plus. And if needs be, I can pilfer wood from the La Toullanaise kit until my stock arrives - woods are similar between the two kits - and looks like they are from the same manufacturing era.

First inspection of the kit revealed everything foreseeable to be present - most importantly, the PLAN!

Opening the box. The wood appears to be VERY dry so I will have to watch that
Kit-Box-1.jpg.17c1d2ffd4a39b98541ddba6332f6bf3.jpg

All the wood seems to be in the box

Kit-Box-2.jpg.3123080946733daa19d16eebdab05622.jpg

Share this post


Link to post
Share on other sites

So the exploration mood quickly changed to a work mood :D

 

I decided to gather all the necessary bits for completing the keel and bulkheads - some of the bulkheads were lazer cut/routed and a few which had to be cut from the ply supplied. 3A ands 2A are used to keep the model on your build board [according to the manual]

 

And on that point, its safe to say the manual sucks a bit - not much info there [and some errors which I will discuss later]

 

Let the cutting commence :D

Bulkhead-cut-1.jpg.3373e4d4a06473d75a73b9045cf0eae2.jpg

Share this post


Link to post
Share on other sites

Quite a bit of cutting to - some of the bulkheads were supplied cut by lazer/CNC cut - I see no burn marks from the lazer so it would be natural to assume it was CNC cut.

The wood is soft so cutting was a breeze to get the required parts - plenty of filing and sanding to do:

Bulkhead-cut-2.jpg.7e32e3ee5afcabf8006da482e4eec1ba.jpg

Bulkhead-cut-3.jpg.b14ca01ec8286ccb70b97237d05f0265.jpg

Bulkhead-cut-4.jpg.3727178aa67f8a18996bcdaeeecc4854.jpg

Bulkhead-cut-5.jpg.3161611f657a1a968c821b3522a25e82.jpg

Share this post


Link to post
Share on other sites

Once the keel and bulkhead parts were shaped and cleaned, it was tine to look at the keel and get it ready for setting in the jig I use 

 

Alas, thats where I discovered the first mistake - the manual calls for a 400mm section of the keel - only to check on the plan to see its actually 392mm. This worries me a bit since the plans were printed presumably from a computer - am wondering if the printed plan has it's scale slightly off?

Anyhow I decided to go with the measurement from the plans [since I will be referring back to it on a regular basis]

 

Plan-1.jpg.c413b6f266f8f4890761db9dba84d4aa.jpg

 

Corrected according to the plan

 

Plan-2.jpg.2ddf10b3bb6651c6d61259c1e9dc1327.jpg

Share this post


Link to post
Share on other sites

This all seems very familiar. I am currently making the Billings 'Etiole' and looking at your plans the method of constructing the hull looks the same. My main problem was that the spacing of the slots in the deck panel for the bulkheads did not match the plans. Hence when it was all assembled the fwd and aft pieces, parts no 2 and 3 in your picture, were a few mm further apart than shown on the plans which meant the strip of wood supplied for the keel was a few mm too short and I had to add a short spacer. I decided it was easier to make the model a few mm longer than shown on the plan rather than try and adjust everything else. In any case, who is to say which is correct.

 

I  think I am trying to say 'Proceed with caution'.

 

Glenn

Share this post


Link to post
Share on other sites

Hi Glen - thanks for stopping by my build log

 

Old story of the instructions not matching the plan - I found a 8mm discrepancy as previously mentioned on the thread

 

Since discovering a few anomolies, I am now using the plan exclusively with just reference to the instructions

Share this post


Link to post
Share on other sites

Just a quick update - have finished the bulkheads. Jeez, nothing lined up, spacing was out and most of the heights were wrong

Dont laugh at my build jig - it works for me till I can make a better - MDF is pricey here in ZA

Bulkheads-1.jpg.320d58fafd5143d42066c50a8e486271.jpgBulkheads-2.thumb.jpg.7665a3be16778950e819c5c679eae3a3.jpg

And then, things can go wrong or an incorrect placement. Time for the doctor to step in :D

 

Mistake-1.jpg.1ea11cd976755fe93cd2e27ef0dac0d9.jpg

Got the deck on after remarking all the cutouts to get a decent fit

 

Deck-planking1b.jpg.bcf8f408a2f3e96540e1338ec57f98b3.jpg

 

Finally manged to get some sense of order for the cutouts

Deck-planking1a.jpg.0d90963b26d5dc0e8c445d2c4402461d.jpg

 

And then starting with the deck planking. I will see what the finish is like but am considering replacing the wood

 

Deck-planking1.jpg.5dbcdedeb6a71e180c233c1e9b8b46f2.jpg

 

Deck-planking2.jpg.bcc1e09fc566aefabdbda1158f9d42c1.jpg

 

Still deciding whether I will put in tree nails or not - yeah. I know the general opinion of many :D

 

 

Deck-1.jpg

Deck-planking2.jpg

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Recently Browsing   0 members

    No registered users viewing this page.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem

Modelshipworld - Advancing Ship Modeling through Research
×
×
  • Create New...