Jump to content

Recommended Posts

Has anyone found band clamps helpful in their modeling?  They seem primarily used for picture frames and boxes.  I continue to have trouble clamping some of the compound planking curves, particularly at the bow and stern.  seems like a band clamp my help if it is not too heavy weight.  I have not been building the more complex old sailing ships but more of the modern boats.

Share this post


Link to post
Share on other sites

The mechanical point about the band-clamps (if you are referring to device that consits of four angles around which a string is lead and tigthened) that the resulting vector of force points to the centre of the workpiece, i.e. it pulls a frame or the side of a box together and also ensures that the corners are 90°. Now in the case of planking the question would be: do you see it running along the strake or perpendicular ? Running along the strake would not be useful unless you run the string over some piece of wood that are put perpendicular to the plank, so that you get a downward force. Winding your vessel with a string running perpendicular to the strake, on the other hand, might be useful to keep planks down. However, planks are often bend in two directions, i.e. not only along the strake, but also to follow upward sweeping curves. With just a string the latter might be difficult to achieve.

 

I frequently use band-clamps in making display cases for models.

Share this post


Link to post
Share on other sites

Wefalck, thanks for the info.  As someone who has used band clamps and also models, I am sure your opinion is correct.  I remain frustrated in finding ways to clamp on the compound curve/angles I run into.

Share this post


Link to post
Share on other sites

Tiger

The photos attached show how I clamped some planks in place using rubber bands and some scrap to hold the pressure where it was needed.  I used this method to hold the whetted planks in place while they dried in place and then again when they were glued in place.  The third photo was from my late friend Joel Sanborn (a NRG and MSW member who's greatly missed) showing how he held planks in place while building the same model - the Gunboat Philadelphia kit by MS.  Maybe these will be useful to you.

Kurt

015 - CLAMPING.JPG

016 - CLAMPS-BANDS.JPG

017 - Joel Sanborns photo 2  DSCN0804.JPG

Share this post


Link to post
Share on other sites

Kurt, thanks for the pics and ideas. Sorry for the late response. I was part of the large group whose homes were flooded here in Houston so my modeling has been hit or miss lately. 

Share this post


Link to post
Share on other sites

A band clamp without the corners employed would work the same as rubber bands. It would apply equal pressure around the hull and in some cases would be easier to apply.

You just need to find one small enough to use.

 

Share this post


Link to post
Share on other sites

Here's my home-made version of the corner-less band clamp.

A length of 3mm elastic cord ('shock cord'), plus one of those little toggles you get on the neck cords or waist cords  of 'hoodie' type garments.

No need to vandalise your wardrobe to make this.  You can get a pack of 20 of those toggles online, for a few cents.

 

The toggle will hold a surprising amount of tension, and the band is easier to fit, adjust and remove than a simple elastic band.DSCN0035r.thumb.JPG.77e3f827f350ab24ab1995fee1a5590d.JPG

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Recently Browsing   0 members

    No registered users viewing this page.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem

Modelshipworld - Advancing Ship Modeling through Research
×
×
  • Create New...