Jump to content

HM Cutter Cheerful 1806 by Blue Ensign - FINISHED - Syren Ship Model Company - 1:48 scale


Recommended Posts

Post 14

Deciding on the paint colour

There is a fair amount of paint on this build, more so than my previous builds, so I was concerned to get a shade that both suited my eye but reflected the more subdued tones of the early 19th c.

I had mixed paints for the Pinnace and Long boat builds that gave a brighter shade than the Admiralty brand Red Ochre (as I used on Pegasus) but I was hoping to find a ready mixed paint that suited. I am not too fussed about whether the paint is enamel(as with Humbrol) or water based.

The paints I am trialling are:

Humbrol 14ml Matt Scarlet enamel paint # 60

Caldercroft Admiralty water based Vermillion

Vallejo 031 17ml Flat Red Acrylic  Paint # 957

Vallejo 029 17ml Dark Vermillion Acrylic Paint # 947

Windsor and Newton Indian Red oils.

 

I made up paint samples on a Boxwood strip for comparison purposes.

DSC05202.thumb.JPG.8c9760fef15ee488badd100e1fb09a4b.JPG

5202

Taken outside, bright daylight.

DSC05204.thumb.JPG.592eced16fe4a1073576dd9e92998a58.JPG

5204

outside close -up

DSC05216.thumb.JPG.1c2740795df9a6ceaef0b84b5192a1d7.JPG

5216

indoors natural light

DSC05218.thumb.JPG.0c6c06afe9705e914f8a8e8e4fb423b3.JPG

5218

Indoors  natural light/warm white leds.

 

The W&N oil was too dark and has the disadvantage of taking a long time to dry.

The Admiralty Vermillion, and Vallejo Dark Vermillion were too bright and altogether the wrong shade of red.

The choice came down to Vallejo Acrylic Flat Red and Humbrol  matt scarlet enamel.

DSC05219.thumb.JPG.6c2575720a2f20ae90783b80d6c694b8.JPG

5219

Vallejo on the left, Humbrol on the right.

 

Colour of course comes down to individual perception, varying light, and monitor differences, but on balance I have decided to go with the Vallejo acrylic flat red.

 

It is slightly darker than the Humbrol and has the advantage of quicker drying and water clean up. It feels better to me, and small amounts can be delivered into a pot for use.

 

I can now proceed.

 

B.E.

 

15/02/2018

 

 

Link to comment
Share on other sites

When you get to this point you really have to admire her shape. Funny your discussing the sub-decking, but for some weird reason I always enjoyed that part of a build. ( not reading about it, but doing it) I guess because it ties the entire thing together. 

 

Kurt

Member: Ship Model Society of New Jersey

Link to comment
Share on other sites

Your color choice of Vallejo flat red looks great. Just as  side note, have you tried Windsor & Newton acrylics? They have some nice colors, go on smooth and cover great without the long dry time of oils.

The heart is happiest when the head and the hands work together.

Al

 

Current Builds:

HMS Halifax 1/48 POF Lumberyard Kit

Model Shipways Glad Tidings

Acoustic Guitar Build FINISHED

Link to comment
Share on other sites

B.E.

 

I've been following your Cheerful build.  I've been meaning to compliment you on your progress.  My build is in dry dock currently while I wait for the time and mental space before I resume work again.  It's been a joy following the progress of the other Cheerful builders though.  Yours is coming along nicely! 

 

Regarding the color of red you're using.  I too decided to use Vallejo Flat Red #957.  I knew from past experience that Vallejo paints are high quality and easy to brush paint with minimal streaks.  I think you won't regret your choice.  To see how the Vallejo flat red looks farther along in the build process, just check out the most recent photos of my build.

 

Keep up the good work!  . . .  and keep the photos coming. 

 

Erik

Link to comment
Share on other sites

Link to comment
Share on other sites

Well, we are no longer at the same place. I decided to “deconstruct” all of the planking. I had used wood that a member of my club gave me because he wasn’t happy with it, now I know why. Besides that the planking wasn’t tight enough too much daylight showing. On the up side Jason at Crown Timberyard will be reopening for business in the middle of March, so I can finally have some decent wood. I just need to be patient. Also this was the first time I used CA for planking and it seems to come apart a lot easier than PVA. 

 

Kurt

Member: Ship Model Society of New Jersey

Link to comment
Share on other sites

B.E.   I had 3 pieces of good boxwood in my stash from Hobbymill before he closed up shop, real quality stuff. So I spent the day reducing it to 3/64 inch for Cheerful planking. I should have done this from the beginning. I have to figure out if it will adhere to the bulkheads where I previously used CA or will need to be worked on to bond with PVA. I really like this model so there’s no hurry. So now I’m trailing behind you and can take full advantage of your interpretation of the Cheerful. I really like the approach you take to your models, both historically correct and very artistic at the same time. I’m looking forward to your next update.

 

Kurt

Member: Ship Model Society of New Jersey

Link to comment
Share on other sites

Post 15

Preparing for planking

The ports have now been painted,

A tip for those who may not have thought of it; those little pill organiser boxes you can get from the chemists make very nice paint mixing boxes.

DSC05383.thumb.JPG.5a3e5e3ff83fdbcdd16a14d1fee1bf93.JPG

5383

Very useful using Vallejo paint where small quantities and some dilution is required. The lid keeps the paint useable for a while and dust free.

Fixing the moulding strip below the ports is next up.

The requirement is that the rail should lay 1/64" below the sill. That's (0.397mm) the thickness of a fine pencil lead!

I was far from sure I could get that close without it looking more like error than intention. I think I will have to gauge this by eye,with 0.5mm about as close as I can practically get and to give a clearly defined rebate.

Starting on the Starboard side I positioned the moulding at the centre port of the hull having marked the point along from the Bow rabbet, and fixed it in position using pva and many clamps.

However once it was done I could see one or two bulges at port sill level where my fairing was not quite enough, so off it came again along the area of the hull affected.

This is quite easy to do with pva, a slight wetting and away it comes. I much prefer to use pva for the woodwork than ca which tends to make the wood brittle, and mark it. Acetone is also required to remove ca. much less friendly than water.

After two or three goes I eventually got a look I could live with although I have not taken it as close as 1/64".

DSC05423.thumb.JPG.3804bd6393c483e35e9bc65e21105002.JPG

5423

DSC05425.thumb.JPG.a16e9de16b08af6b70ca7d84fdd2ea27.JPG

5425

DSC05415.thumb.JPG.ea556ca2fa9acd0c3564ccbea148fd94.JPG

5415

I was keen that the mouldings appeared level on each side, and fortunately this appears to be the case.

DSC05422.thumb.JPG.c90d3c599c529f4fbd1ff307d094af4d.JPG

5422

DSC05426.thumb.JPG.3c18670c89eca71bc24e2d335080490a.JPG

5426

DSC05429.thumb.JPG.632815d6f91c391725af163f48828621.JPG

5429

 

The first planking above the wale now beckons.

B.E.

20/02/2018

Link to comment
Share on other sites

B.E.  I like your idea of assuring the moldings are both at the same height at the stern. I'll definitely do that this time around. Some solutions are so obvious once you see it done. I found the molding at the first gun port a nuisance the first time. This time I'll make in a single piece and remove the gun port section afterwards. I also thought the 1/64" rabbit was a little too small. After all that red paint covered over. I'll probably go a hair wider.

 

I'm wondering how to treat the wales final thickness. It tapers in thickness until it's flush with the normal planking at the bow. I think Chuck realised it after in was in place and then sanded it to shape. I wonder if both the first and second layer should both be tapered or, just the first or the second. I sort of don't like the idea of the top layer feathering to nothing.

 

Kurt

Member: Ship Model Society of New Jersey

Link to comment
Share on other sites

Hey B.E.   I'm enjoying your Cheerful build log and have already learned a few things. 

The Admiralty model of the Cheerful/Surly is here in the US at the museum of the US Naval Academy at Annapolis, Maryland.  I took these photos on a recent visit there.  Thought you would enjoy them.

2016_04_20_02.jpg.6a76c36047acc74b5563be99f8a5676a.jpg

 

2016_04_20_01.jpg.0ce0bac32c35abf19dcdd09b5b471cd7.jpg

The back of the case is a mirror - there aren't two models in the photo.

Cheers.

Ken

 

NO PIRACY 4 ME! (SUPPORTING CHUCKS' IDEA)

 

Current Build:  

Washington 1776 Galley

Pilot Boat Mary of Norfolk

Completed Builds:

Continental Boat Providence   (from Completed Gallery)  (from MSW Build)

Continental Ship Independence  (from Completed Gallery)  (from MSW Build)

Rattlesnake   (from Completed Gallery)  (from MSW Build)

Armed Virginia Sloop  (from Completed Gallery)

Fair American (from Completed Gallery)  (from MSW Build Log)

 

MemberShip Model Society of New Jersey

                  Nautical Research Guild

Link to comment
Share on other sites

  • 2 weeks later...

Thank you Ken,

 

Post 16

Planking above the Wale

The first plank above the wale is done using 3/16"wide  x 3/64" thick strip.(4.7625mm x 1.2mm)

There is a taper required both fore and aft on the first plank to even out the widths with the second plank.

I started my fore taper just aft of the second port, and the aft taper just past the third port from aft. These were quite shallow tapers.

With the tapers done I clamped the first plank in place and gave it the heat treatment to impart a little curve memory around the bow.

Trialling the fit some tweaking was required to get the strip to lie  flush to the rail, a couple of high/low spots on the bulkheads.

DSC05582.thumb.JPG.42d4eae46ee4844cca75298f95515646.JPG

5582

DSC05581.thumb.JPG.147e761aa5cf4d01dca02a212a86522a.JPG

5581

It was then a question of gluing progressively along the hull clamping it both to the bulkheads and the Wale. I initially glued to the first six bulkheads, then worked aft at three at a time.

DSC05627.thumb.JPG.9631001b14183b932b64b73d7f17a87c.JPG

5627

DSC05630.thumb.JPG.6b1bb64618bb2b7d37af400cda8116ab.JPG

5630

I fitted the lower strip on both sides before moving on.

Note:

Looking at photo's of Chuck's prototype build there are three butt joints along the first plank. 1 just aft of the first port a 2nd just aft of port 3, and a third just forward of port 6.

Strangely on the plans (Plan 1) only two butt joints are shown?

I didn't cut the planks into scale lengths, but replicated the 'joint'  with a shallow micro saw cut, and then marked it with a pencil lead.

The second plank above the wale was done using 7/32" wide by 3/64" thick strip (5.56mm x1.2mm)

This strake to fill in up to the moulding rail required some fettlin' with tapers both fore and aft.

DSC06078.thumb.JPG.a62688ef67e7a207b9d0f529a964a589.JPG

6078

I used Tamiya 10mm tape to give me a template along the hull for the shape of the upper plank which gave me the rough top line of the plank beneath the moulding rail.

It was then a question of using a scalpel blade to pare the strake down progressively to fit. As it turned out it was more of a spile than a simple taper.

I use a Pilot broad chisel waterproof marker to represent the tar line between planks.

DSC05752.thumb.JPG.ba0abbeb8ddbdb34ac35d1c353ac31a0.JPG

5752

Fixing the upper strake in place.

DSC06369.thumb.JPG.2c9932e615257c2ceaa94eed16fc1da0.JPG

6369

Got a little fettlin' to do around the fore port sill line.

DSC06371.thumb.JPG.ad5bcf691704775274aeb6748f7a8384.JPG

Moving on now to working out a strategy for the planking between the ports.

B.E

02/03/2018

 

Edited by Blue Ensign
Link to comment
Share on other sites

Good progress B.E.

 

the single-planking is coming on mighty fine...:)

 

Nils

Current builds

-Lightship Elbe 1

Completed

- Steamship Ergenstrasse ex Laker Corsicana 1918- scale 1:87 scratchbuild

"Zeesboot"  heritage wooden fishing small craft around 1870, POB  clinker scratch build scale 1:24

Pilot Schooner # 5 ELBE  ex Wanderbird, scale 1:50 scratchbuild

Mississippi Sterwheelsteamer built as christmapresent for grandson modified kit build

Chebec "Eagle of Algier" 1753--scale 1:48-POB-(scratchbuild) 

"SS Kaiser Wilhelm der Grosse" four stacker passenger liner of 1897, blue ribbond awarded, 1:144 (scratchbuild)
"HMS Pegasus" , 16 gun sloop, Swan-Class 1776-1777 scale 1:64 from Amati plan 

-"Pamir" 4-mast barque, P-liner, 1:96  (scratchbuild)

-"Gorch Fock 2" German Navy cadet training 3-mast barque, 1:95 (scratchbuild) 

"Heinrich Kayser" heritage Merchant Steamship, 1:96 (scratchbuild)  original was my grandfathers ship

-"Bohuslän" , heritage ,live Swedish museum passenger steamer (Billings kit), 1:50 

"Lorbas", river tug, steam driven for RC, fictive design (scratchbuild), scale appr. 1:32

under restoration / restoration finished 

"Hjejlen" steam paddlewheeler, 1861, Billings Boats rare old kit, scale 1:50

Link to comment
Share on other sites

Neat work, there, BE.  I always like seeing the hull shape that emerges as the planking goes on.  And Cheerful is a lovely little thing, isn't she?

 

Cheers,

 

Martin

Current Build:  HMS FLY 1776

 

Previous Builds:  Rattlesnake 1781

                        Prince de Neufchatel

Link to comment
Share on other sites

Thank you Thomas and Martin.

'Lovely little thing' is a relative term for me at the moment.:rolleyes:

This is my least favourite part of a build Martin, always looks untidy to me, made worse by looking at Chuck's build photo's, they really should carry a warning 'Looking at these photo's can seriously damage your build confidence'  ;) Hopefully once it's all been sanded I'll feel happier about it.

Not heard much from the prairie of late, hope you and yours are ok and that you are making some progress on Fly.

 

Regards,

 

B.E.

Link to comment
Share on other sites

Post 17

Planking between the ports.

I have scratched my head over the best approach (for me)  to tackle this job.

The problem seems to be getting a constant narrow line each side of the ports to form the rebate, and getting the plank ends angled correctly given the slight sheer of the moulding rail against which the first plank must adhere.

To begin the process I wetted and heat treated a full length of 5/32nd strip along the hull to impart the curve.

DSC06640.thumb.JPG.b11959f30052cbce56659761fe647f60.JPG

6640

The section between each port was then marked on the plank, and the laborious process of cutting and fitting began.

DSC06648.thumb.JPG.bd3d7e008b38cd75d19c8e24dd79d784.JPG

6648

Each section was cut roughly to size, clamped into place and given the heat treatment again.

DSC06650.thumb.JPG.4524147f0a7049044bb393ac099230c6.JPG

6650

The ends were then cut using a scalpel, and pva'd into place.

I found this to be slow and testy work.

DSC06649.thumb.JPG.8004433b681bf3de894d9af5b94131bb.JPG

6649

Getting  there.

DSC06656.thumb.JPG.a1f75ed24bb912f1ca308505fa1dcd20.JPG

6656

DSC06651.thumb.JPG.130a220609f798de781e833b292e0ab6.JPG

6651

Starboard side completed, or rather planked; there is a lot of tweaking and cleaning up to do.

 

One area that caused me some confusion was fitting the last two strakes aft of the last port running up to the stern post.

DSC06654.thumb.JPG.3f442e45a9669a858e68d28a5224da02.JPG

6654

These were both tapered in accordance with the instructions and to the plan dimensions, but unlike Chuck's photo's in the relevant section,(Chapter 3, page3) the last strake did not run to the top of the outer stern frame. :huh:

 

Into panic mode, fingers crossed the outer strakes are reduced in height to form the transom curve, otherwise I'm in trouble.:o

Onto the Port side.

 

B.E.

06/03/2018

 

 

Link to comment
Share on other sites

Really nice work BE.  Fingers crossed here for you as well, but I'm sure you'll figure out a solution if you need one.

Mike

 

Current Wooden builds:  Amati/Victory Pegasus  MS Charles W. Morgan  Euromodel La Renommèe  

 

Plastic builds:    SB2U-1 Vindicator 1/48  Five Star Yaeyama 1/700  Pit Road Asashio and Akashi 1/700 diorama  Walrus 1/48 and Albatross 1/700  Special Hobby Buffalo 1/32  Eduard Sikorsky JRS-1 1/72  IJN Notoro 1/700  Akitsu Maru 1/700

 

Completed builds :  Caldercraft Brig Badger   Amati Hannah - Ship in Bottle  Pit Road Hatsuzakura 1/700   Hasegawa Shimakaze 1:350

F4B-4 and P-6E 1/72  Accurate Miniatures F3F-1/F3F-2 1/48  Tamiya F4F-4 Wildcat built as FM-1 1/48  Special Hobby Buffalo 1/48

Citroen 2CV 1/24 - Airfix and Tamiya  Entex Morgan 3-wheeler 1/16

 

Terminated build:  HMS Lyme (based on Corel Unicorn)  

 

On the shelf:  Euromodel Friedrich Wilhelm zu Pferde; Caldercraft Victory; too many plastic ship, plane and car kits

 

Future potential scratch builds:  HMS Lyme (from NMM plans); Le Gros Ventre (from Ancre monographs), Dutch ship from Ab Hoving book, HMS Sussex from McCardle book, Philadelphia gunboat (Smithsonian plans)

Link to comment
Share on other sites

BE, I'm doing the same thing now, except I've been alternating sides with each port. No particular reason for it. Like you said, they'll be a lot of fine tuning. It's going to take a lot of fine touch up on the red to be sure. I have the same concern about the stern area. I guess after clean up I'll mask the molding bases and then give the area a coat of poly. I'm toying with the idea of applying a filler of acrylic media and paint to fill in any gaps between planking, which fortunately are few. I am wondering if that would just draw attention to them. I guess I'll try an experiment on some scrap first.

 

Kurt

Member: Ship Model Society of New Jersey

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...