Jump to content

Recommended Posts

So I masked off a part of the hull of the ship I want to paint, and applied primer, then paint. However, when I removed the making tape, I get a line of white primer visible on the edge. It's not because the primer seeped under the making tape, but because when the masking tape is removed, the cross section of the layering became visible.

The only way I can think to avoid this, is to not apply the primer all the way to the edge, but is there a better way?

Share this post


Link to post
Share on other sites

Not sure I understand the problem correctly, but normally one would paint the lighter colour first, overlapping well the separation line to the darker colour - no masking at this stage. Then you mask off the area already painted and proceed with painting the darker colour. So there are no edges of under-paint exposed.

Share this post


Link to post
Share on other sites
3 hours ago, wefalck said:

Not sure I understand the problem correctly, but normally one would paint the lighter colour first, overlapping well the separation line to the darker colour - no masking at this stage. Then you mask off the area already painted and proceed with painting the darker colour. So there are no edges of under-paint exposed.

I'm painting just a single line a single color, not the entire ship. The rest is natural wood. The problem is the primer is showing.

Share this post


Link to post
Share on other sites

Why do you prime ? For a single coloured line (boot-top ?) this is not normally needed, I would think. I suppose you would have applied some sanding sealer and varnish to the natural wood already ?

 

Instead of masking and painting, you may also think of a decal, to be sealed with varnish or not, depending on the kind of model.

Share this post


Link to post
Share on other sites

Another alternative is to use either auto pin striping tape or tapes available from chartpak in the width you want.  I used chartpak tape for the waterline on the Bluenose II that I built 35 years ago and it still looks as good as the day it was put on.  I used clear lacquer to coat the tape once installed.

 

As is typical, I responded half way through a thought and assumed you would know where I was.  Let me make myself clear on this.  I did not paint a waterline, I used tape instead of paint for the waterline.

002 (2016_10_16 17_34_19 UTC).JPG

Edited by bogeygolpher
Clarity

Share this post


Link to post
Share on other sites

It sounds like the paint is pretty thick if you can see the primer under the paint and it isn't bleed.  The fix is to either remove all the paint and redo it or mask next to the line making the line a bit wider and then don't prime but add a layer of paint out to the tape.  Remove the tape and the previous edge should be hidden by the paint.  I think removal and starting over might make a better job of it.

 

Also, it sounds like the tape was pretty thick to allow a build up of primer and paint so the edge is able to be seen.  Never use hardware store masking tape - it is too sticky and the edges are not straight and smooth and it's real thick.  Use a good automotive or hobby masking tape.  Tamiya tape is good as is 3M Fine Line tape.  I have switched to FBS K-UTG Gold Crepe masking tape from Coast Airbrush (link below).  It is a very thin tape that isn't too sticky - sticky tape can lift underlying paints - and conforms well.  The thin tape doesn't let paint build up alongside it.    https://www.coastairbrush.com/proddetail.asp?prod=FBS_K-UTG_Gold_Crepe_Masking_Tape

 

Hope this helps

Kurt

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Recently Browsing   0 members

    No registered users viewing this page.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem

Modelshipworld - Advancing Ship Modeling through Research
×
×
  • Create New...