Jump to content

18th Century Longboat by Dowmer - FINISHED - Model Shipways - 1:48 - As used in the PNW fur trade circa 1790


Recommended Posts

Hello fellow shipbuilders

 

I’ve been a member of MSW for awhile, but while I have gleaned considerable mounts of techniques and information, I haven’t “given back” by contributing a build thread. So I figured I’ll dip the proverbial “toe” into the lake of knowledge and wade gently into the wash of expertise here in MSW.  Although the initial build of the hull is finished, I will be rigging the model and will continue to post my progress.

 

I have modeled for years and my passion has waned from ships to giant scale RC aircraft and now back to ships.  I will admit that my ship modeling has increased my scale fidelity in aircraft considerably, but my first love is the sea so the ships call again.  So hear I am. Jumping back into the ship realm after 15 years of dormancy and to be honest, it feels like coming home after an extended trip. I will try my best to make an acceptable model but doubt that it will ever touch the level of perfection seen by many on this site.

 

The subject is the 18th century longboat designed by Chuck Passaro in 1/4 scale (1:48).  However, it will be a blank canvas to serve as inspiration for the true subject, an 18 century merchant longboat used in the Pacific Northwest fur trade circa 1790.  I never build kits per plans.  I like subjects that are unique and that include some research.  So the kit will provide a starting point for departure.

 

My main interest per my signature line below are the historical and exploration vessels of the PNW coast. As such, I figured it would be interesting to build a longboat that could theoretically be used from a frigate like Columbia Redidiva (name sake of the Columbia river in Oregon).

 

Some planning assumptions:

 

  1. The larger ships that the boats came from were small, so the longboats, cutters, yawls and jolly boats that accompanied them were small as well to fit between the masts or on deck.
  2. Reviewing their logbooks, these small boats 16-24 feet were constantly employed shifting and setting the anchors for warping or mooring in the treacherous tidal and unknown waters.
  3. Typically the boats were armed with swivel guns and muskets.
  4. Sailing rig seems to be either a gaff or lug sail rig that was preferred.
  5. The boats needed to be very sea worthy due to the unpredictable weather, tides and heavy usage lightering water casks, wood, furs and supplies to and from shore.
  6. Due to unknown shoal water throughout the area, these boats were typically employed trading for furs with the natives in shallow water while the larger ship stood off the lee shore in deeper water.  This offered the boats the opportunity to explore and operate independently for a considerable time.  Terrifying if you think about how small they were in a hostile land halfway around the world will little supplies or support if stranded.
  7. As far as paint or preservation, merchant ships were typically cheap and paint as a luxury and was used sparingly for preservation.  Paint was expensive and cut into profit.  Reviewing logbooks showed that the typical paint carried was lampblack, Spanish brown, and varnish.

 

Enough of my blathering........

 

I built the basic hull earlier before I decided to do a build thread.  Sorry, no build picks.  But I assure you that the construction was the same as all of the other 18th century longboat kits on this site.  No real revelations or deviations from the basic construction.  I used only the basswood parts provided in the kit.  If I had it to do over, I’d probably mill my own yellow cedar and boxwood for the planking and parts.  The basswood is soft and a pain to work with and the grain is too fuzzy.  One of my least favorite woods.

 

Here’s the hull built.  I’ll point out some of the unique features.  Paint was lamp black, hull white and satin poly-c.

 

 

5CF23A25-6B08-4A49-B86D-C960523F3667.thumb.jpeg.4906547033985986fb87f171cb94b449.jpeg

 

 

I added a bit more sheer than the plans called for simply because I like the look and some of the plans from NMM had the amount I was looking for, so I figured it could be justified. Instead of thole pins supplied in the kit for the oars, I used another option that is typical of the time period instead of a washboard. I’m not sure what you call it.  Why did I use this style, I don’t know, I like the look 😃.

 

 

 

9A63A7F0-A5E6-4A36-8384-1F9453F7E282.thumb.jpeg.c57f67f395036c66d9477c7ba50612d2.jpeg

 

There was quite a bit of discussion on some other threads about placement of the horse.  I chose the option of above the tiller. There are plans circa 1800 that show this so it fits and seems logical. You can also see the tree nails used in the planking.  Holes drilled and filled with hobby putty as shown by Chuck in his builds.  I typically like to use actual treenails but at this small of a scale with it being so fragile I decided to give Chucks method a try.  It worked well.

 

 

6CA0D6E1-0951-4603-AB39-DC4F549B4D99.thumb.jpeg.dcc28c356461caf90a32eec1cc4aabba.jpeg

 

Below you can see that I added a post for a swivel forward of the second thwart, let into the raised deck into the keelson and secured and notched into the supported thwart.   The swivel gun itself was purchased from Chuck at Syren Shipmodels.  The handle, was 24 gage wire bent around the pommel and blackened.  The metal supporting bands on the post and swivel support carriage were made out of paper and painted black.  You can also see that I added a roller to the bow like BobF did with his boat.  Very functional considering the heavy work that the boat would be doing moving anchors etc.  The grapnel anchor rests on the floorboards.

 

 

A02B6084-CAC0-432F-A025-E6B121AFFD8C.thumb.jpeg.86ea8ed632dd3a568f983e4758fbb9c5.jpeg

 

 

The chainplates have eyes for hooks instead of strapped into the deadeyes. This allows the rigging to be set up and taken down quicker. The NMM model is set up like this. 

 

 

 

6CA0D6E1-0951-4603-AB39-DC4F549B4D99.thumb.jpeg.dcc28c356461caf90a32eec1cc4aabba.jpeg

 

 

Finally, I added a block onto the stem for the outhaul for the jib. If you look at the NMM model it has this feature but isn’t rigged. If you look closely there is some damage to the bowsprit so I assume the rigging was probably repaired at some point and perhaps not rigged. There are contemporary paintings and plans showing this out haul rigged through a block such as this. I’m assuming that it helped hold the bowsprit when the jib was rigged in brisk winds, acting like a bobstay. 

 

 

 

9892465A-9CEE-4937-8FBF-CDA0FF94D52E.thumb.jpeg.8a869c1eca5769c0d703e8211f6346ee.jpeg

 

A few more pics

 

E1234306-EFA0-4C70-9965-72468F95921A.thumb.jpeg.5be291cf50f1228ba8ee9e721df3ca51.jpeg

 

 

 

A75CFBBE-8E23-4ABB-A021-2EE41E3A3DBC.thumb.jpeg.8d667f6ee0f327286961baade7a32a7a.jpeg

 

 

So with the hull complete its time for the rigging. The next installment will start where I’m currently at.  We are now all caught up.  I hope you have enjoyed it so far.

 

 

 

 

 

 

 

 

 

 

 

Able bodied seaman, subject to the requirements of the service.

"I may very well sink, but I'm damned if I'll Strike!" JPJ

 

My Pacific Northwest Discovery Series:

On the slipways in the lumberyard

Union, 1792 - 1:48 scale - POF Scratch build

18th Century Longboat - circa 1790 as used in the PNW fur trade - FINISHED

 

Future Builds (Wish List)

Columbia Redidiva, 1787

HM Armed Tender Chatham, 1788

HMS Discovery, 1789 Captain Vancouver

Santiago, 1775 - Spanish Frigate of Explorer Bruno de Hezeta

Lady Washington, 1787 - Original Sloop Rig

 

Link to comment
Share on other sites

My favorite part is rigging.  My work table is nothing special, just a card table in the basement and a vise.  Most of the boat was made with this arrangement which goes to show that you don’t need much to build one of these boats. 😉

 

 

I started with the stays. With the forestay and back stays added it will hold the mast in place pretty well so I can seize the deadeyes in place without everything shifting all over the place.  I made most of the standing rigging off the model so I could slip them over the masthead in the correct order.  

 

The metal fittings and mast cap at the top are not fitted yet.....err perhaps I should say they were removed once I found out I couldn’t get the standing rigging over the mast head.  😟  I’ll add them later after I’m sure everything is in place.  All the lanyards are tied off temporarily until I get the deadeyes turned in and can adjust everything.

 

 

54F176E7-0A40-4F67-929D-96142191C000.thumb.jpeg.0ecf3204b4cf100bcee4efcef114ce8a.jpeg

 

 

Below you can see the backstays hooked into the eyes of their respective chainplate.

 

11AA3AE6-A6EE-4D59-A792-9F854AB09994.thumb.jpeg.27ef056a28c19cbf3c2091e75b6009ea.jpeg

 

Another view from the bow.  The belaying pins still need to be blackened.  The bowsprit is only sitting in place.  A block has been added to the horse aft for the main sheet.

 

A5771829-F24C-40E7-A8D4-10081B47ED0C.thumb.jpeg.b69222bb124c6a3db6f60a8996869265.jpeg

 

 

 

DB84AC36-DDDF-4EAB-B36B-0FC0535BE20D.thumb.jpeg.22eb871369b16137994ab7c21af09606.jpeg

 

Next I’ll turn the deadeyes into their respective shrouds and hook them onto the plates.  That’s all for now.

 

 

 

 

 

 

 

 

 

Edited by Dowmer

 

 

 

Able bodied seaman, subject to the requirements of the service.

"I may very well sink, but I'm damned if I'll Strike!" JPJ

 

My Pacific Northwest Discovery Series:

On the slipways in the lumberyard

Union, 1792 - 1:48 scale - POF Scratch build

18th Century Longboat - circa 1790 as used in the PNW fur trade - FINISHED

 

Future Builds (Wish List)

Columbia Redidiva, 1787

HM Armed Tender Chatham, 1788

HMS Discovery, 1789 Captain Vancouver

Santiago, 1775 - Spanish Frigate of Explorer Bruno de Hezeta

Lady Washington, 1787 - Original Sloop Rig

 

Link to comment
Share on other sites

Fright,

Thanks for visiting my thread and the complement. I hope this boat will be a little bit different then the standard longboat built by many. 

 

Cheers

 

 

 

 

 

Able bodied seaman, subject to the requirements of the service.

"I may very well sink, but I'm damned if I'll Strike!" JPJ

 

My Pacific Northwest Discovery Series:

On the slipways in the lumberyard

Union, 1792 - 1:48 scale - POF Scratch build

18th Century Longboat - circa 1790 as used in the PNW fur trade - FINISHED

 

Future Builds (Wish List)

Columbia Redidiva, 1787

HM Armed Tender Chatham, 1788

HMS Discovery, 1789 Captain Vancouver

Santiago, 1775 - Spanish Frigate of Explorer Bruno de Hezeta

Lady Washington, 1787 - Original Sloop Rig

 

Link to comment
Share on other sites

Tasmanian,

Thanks for visiting. You should have an enjoyable time building this boat.  Be sure you support the frames well when you fair the ribs for the planking and take your time.  This fragile small boat is not an inexperienced build.

 

 

 

 

 

Able bodied seaman, subject to the requirements of the service.

"I may very well sink, but I'm damned if I'll Strike!" JPJ

 

My Pacific Northwest Discovery Series:

On the slipways in the lumberyard

Union, 1792 - 1:48 scale - POF Scratch build

18th Century Longboat - circa 1790 as used in the PNW fur trade - FINISHED

 

Future Builds (Wish List)

Columbia Redidiva, 1787

HM Armed Tender Chatham, 1788

HMS Discovery, 1789 Captain Vancouver

Santiago, 1775 - Spanish Frigate of Explorer Bruno de Hezeta

Lady Washington, 1787 - Original Sloop Rig

 

Link to comment
Share on other sites

I forgot to mention for the rigging line and blocks I’m using parts from Syren Ship Model Company.  The stuff provided by Model Shipways in this kit are about the cheapest, crappiest stuff I’ve seen.  Definitely low grade nylon rigging line.  So it helps to upgrade these or make them yourself for a much better look.

 

Heres a pic of Syren upgrade items.

 

 

467548A4-6E9D-465A-AF3B-9B7C83CF207D.thumb.jpeg.17e532622148b76c8d4ccfe372f369f9.jpeg

 

 

 

 

 

 

Able bodied seaman, subject to the requirements of the service.

"I may very well sink, but I'm damned if I'll Strike!" JPJ

 

My Pacific Northwest Discovery Series:

On the slipways in the lumberyard

Union, 1792 - 1:48 scale - POF Scratch build

18th Century Longboat - circa 1790 as used in the PNW fur trade - FINISHED

 

Future Builds (Wish List)

Columbia Redidiva, 1787

HM Armed Tender Chatham, 1788

HMS Discovery, 1789 Captain Vancouver

Santiago, 1775 - Spanish Frigate of Explorer Bruno de Hezeta

Lady Washington, 1787 - Original Sloop Rig

 

Link to comment
Share on other sites

Nicely done Dowmer

 

I wish my building skills could even come close to yours.

 

One thing you may have forgotten in your original description though is that sometimes the trading ships carried their smaller boats as lumber in the hold, not assembling them until they reached the PNW.

 

Again great build and a worthy addition to your collection, (Or what will someday be your collection).

Lou

 

Build logs: Colonial sloop Providence 1/48th scale kit bashed from AL Independence

Currant builds:

Constructo Brigantine Sentinel (Union) (On hold)

Minicraft 1/350 Titanic (For the Admiral)

1/350 Heavy Cruiser USS Houston (Resin)

Currant research/scratchbuild:

Schooner USS Lanikai/Hermes

Non ship build log:

1/35th UH-1H Huey

 

Link to comment
Share on other sites

Thanks Lou, I appreciate your kind comments.

 

32 minutes ago, lmagna said:

One thing you may have forgotten in your original description though is that sometimes the trading ships carried their smaller boats as lumber in the hold, not assembling them until they reached the PNW.

 

You are correct, but these generally were not longboats, but larger sloops or schooners around 40 tons that they carried as frames in the hold. The Columbia carried the Adventure in her hold and it was assembled South of Nootka Sound, B.C during the winter of 1788. The first ship built on the PNW coast.  All the other timber was sawn on site by their carpenter. Wow, what a job that must have been! 🤪

 

 

 

 

 

 

Able bodied seaman, subject to the requirements of the service.

"I may very well sink, but I'm damned if I'll Strike!" JPJ

 

My Pacific Northwest Discovery Series:

On the slipways in the lumberyard

Union, 1792 - 1:48 scale - POF Scratch build

18th Century Longboat - circa 1790 as used in the PNW fur trade - FINISHED

 

Future Builds (Wish List)

Columbia Redidiva, 1787

HM Armed Tender Chatham, 1788

HMS Discovery, 1789 Captain Vancouver

Santiago, 1775 - Spanish Frigate of Explorer Bruno de Hezeta

Lady Washington, 1787 - Original Sloop Rig

 

Link to comment
Share on other sites

22 minutes ago, Dowmer said:

Wow, what a job that must have been!

Probably not much different than it would have been in most of the eastern seaboard ship yards back then except the entire labor force was made up of crew instead of local labor, and the lumber would have been green. Ship building seemed like mush more of a cottage industry back then.

 

But it is possible that small ship building has not changed all that much in over 200 years. We have a small shipyard about a mile from my house on the river that builds large harbor tugs in about the 100' range that is really not much larger than the boats they build. 

Lou

 

Build logs: Colonial sloop Providence 1/48th scale kit bashed from AL Independence

Currant builds:

Constructo Brigantine Sentinel (Union) (On hold)

Minicraft 1/350 Titanic (For the Admiral)

1/350 Heavy Cruiser USS Houston (Resin)

Currant research/scratchbuild:

Schooner USS Lanikai/Hermes

Non ship build log:

1/35th UH-1H Huey

 

Link to comment
Share on other sites

A bit of an update.  Deadeyes seized on the port side and starboard side forward. One more to go.   😃  I made a convenient jig to hold the deadeyes in place. I know this has been covered in other threads before but for those that haven’t seen it I show what I did. 

 

I used some 26 gage wire that just fit in the holes of the deadeye and cut some short pieces about 1.5 inches long. Then put about a 30-45 degree bent in the middle. The amount isn’t important but it should be enough to separate the ends when you put the two together.  I then soldered them together.  See pic.

 

9AEE9B00-389D-480B-B8F6-B73E3397ED47.thumb.jpeg.495309c6296a493cabf39a0129d42cca.jpeg

 

Next I straightened them out and wrapped them around two small nails the distance I wanted between the deadeyes. 

 

82B72EF2-22E4-4895-918C-9B6DF64A44DA.thumb.jpeg.6b01cd1f0cf451fdb1d96cdca516e07d.jpeg

 

 

This created the holding jig. I only made two, one for each side, but you could easily make more.  It only took t minutes to make them. 

 

 

 

 

16C0BFC3-7FFC-45AE-8886-0AF5C99FEBCE.thumb.jpeg.c56ea016d59f15efdf01bd2eeb6c49b5.jpeg

 

A pic showing them in action. Very convenient. 

 

106F0D99-3767-4CB7-8FBA-CC86F9F06533.thumb.jpeg.03eca92839b55d57733141c816734b85.jpeg

 

A few more

 

DEE2DE56-9BFF-45F3-A24D-BB09D801D833.jpeg.721b8a1f6206e4d0fe99d92cd702bbe3.jpeg

 

20F9AA7E-F5CD-4717-A98A-79D3BD9B131D.thumb.jpeg.3c4bcb9338d87151b0579110573183c6.jpeg

 

Then time to rove the lanyards. There are some good discriptions on how to set up the deadeyes in contemporary works.  One of them is “The young Sea officers sheet anchor” by Darcy Lever.  As the shroud cables cross each other and are seized at the top of the deadeye at the top, the short end should lay on the aft side port and the forward side starboard.  The stopped knot of the lanyard will be placed on the opposite side and reeve though the deadeyes and lashed to the shroud above.

 

 

5984F9AC-F329-47B1-8E94-05179F2B002B.thumb.jpeg.e5ec5dc8ab5dc4839590bb8bf118da09.jpeg

 

The pic below is not finished on the starboard side.  The lanyard is only tight to check the tension and spacing.  But you can see the bottom deadeye hooked to the chainplate. These extreme closeups are very unforgiving. 😥

 

6E63A852-FF54-4CAE-9386-85849A161769.thumb.jpeg.bd7375b204acf7799437f9caccd41a4a.jpeg

 

I also drilled another hole in the stem for the stay lanyard.  After close inspection of the NMM model I noticed there are three holes, not two.  Lanyard set up and seized to the stay.

 

 

5F207F1C-586A-4BF3-9007-8045C66CDFC4.thumb.jpeg.b219f0f099001a2723f6dbad71081a9e.jpeg

 

A couple of other spare pics for setting up the deadeyes.

 

4C892425-4DA8-49A7-8627-DB4957CA82EB.jpeg

 

148D6BA3-C0DC-462C-9939-FDE6569B4B89.jpeg

 

 

Enough for now.  Enjoy.

 

 

 

Edited by Dowmer

 

 

 

Able bodied seaman, subject to the requirements of the service.

"I may very well sink, but I'm damned if I'll Strike!" JPJ

 

My Pacific Northwest Discovery Series:

On the slipways in the lumberyard

Union, 1792 - 1:48 scale - POF Scratch build

18th Century Longboat - circa 1790 as used in the PNW fur trade - FINISHED

 

Future Builds (Wish List)

Columbia Redidiva, 1787

HM Armed Tender Chatham, 1788

HMS Discovery, 1789 Captain Vancouver

Santiago, 1775 - Spanish Frigate of Explorer Bruno de Hezeta

Lady Washington, 1787 - Original Sloop Rig

 

Link to comment
Share on other sites

Very nice work Dowmer,  and I disagree, it holds up even in the close up pictures. 

Lou

 

Build logs: Colonial sloop Providence 1/48th scale kit bashed from AL Independence

Currant builds:

Constructo Brigantine Sentinel (Union) (On hold)

Minicraft 1/350 Titanic (For the Admiral)

1/350 Heavy Cruiser USS Houston (Resin)

Currant research/scratchbuild:

Schooner USS Lanikai/Hermes

Non ship build log:

1/35th UH-1H Huey

 

Link to comment
Share on other sites

Lou, thanks for dropping by and you are very kind.

 

Steve, thanks.  I appreciate the comment.

 

 

 

Able bodied seaman, subject to the requirements of the service.

"I may very well sink, but I'm damned if I'll Strike!" JPJ

 

My Pacific Northwest Discovery Series:

On the slipways in the lumberyard

Union, 1792 - 1:48 scale - POF Scratch build

18th Century Longboat - circa 1790 as used in the PNW fur trade - FINISHED

 

Future Builds (Wish List)

Columbia Redidiva, 1787

HM Armed Tender Chatham, 1788

HMS Discovery, 1789 Captain Vancouver

Santiago, 1775 - Spanish Frigate of Explorer Bruno de Hezeta

Lady Washington, 1787 - Original Sloop Rig

 

Link to comment
Share on other sites

Standing rigging done today. 😀  On to the running rigging.  This is such a small boat, the running rigging won’t take long.

 

 

View from the bow.  You can easily see the block on the stem for the outhaul and the grapnel and swivel behind the forward stay.

 

 

0B20816E-998A-43B8-969F-F06A7929FFF8.thumb.jpeg.a85409efd6bb4d270f0d113eb812c8a5.jpeg

 

View looking forward.  You can see the backstays tied off and the rigging lashed to the block and hook.  This was shown on the NMM Model and makes sense so I copied it.

 

 

0D4FEC44-CEA5-4998-BAD5-6D89B4E709D4.thumb.jpeg.362cfaa1efda287cb860a90cbd8ad934.jpeg

 

 

0E170F32-798E-4CC6-BB35-F7DFDB95A293.thumb.jpeg.2517b2f16e1b3fe279b8a298ba70a193.jpeg

 

 

Port side view 

 

 

E8ED5217-D3F0-4F91-AF4F-5C56986939A8.thumb.jpeg.d6df69ee9a3f85f8f17a688c990cf7f0.jpeg

 

 

Starboard side view

 

 

26C1C386-89C7-491D-9833-52F8958AB3CF.thumb.jpeg.f7abb26ca68725cd6a3565536756f9e8.jpeg

 

 

Standing rigging at the mast hounds

 

 

A497C0C3-D28C-4AD8-AE1B-8A081FFCDFFC.thumb.jpeg.5d6d2ebac70744b36690d1153e919229.jpeg

 

 

Overall view.  Now time to finish it up.  Boom and gaff next with the jib halyard on the bowsprit.

 

19F4EA1F-23F0-4926-8D4B-BC072F5F1566.thumb.jpeg.bb1d6bec9821f1710c1495fdb7fe3375.jpeg

 

 

 

 

Edited by Dowmer

 

 

 

Able bodied seaman, subject to the requirements of the service.

"I may very well sink, but I'm damned if I'll Strike!" JPJ

 

My Pacific Northwest Discovery Series:

On the slipways in the lumberyard

Union, 1792 - 1:48 scale - POF Scratch build

18th Century Longboat - circa 1790 as used in the PNW fur trade - FINISHED

 

Future Builds (Wish List)

Columbia Redidiva, 1787

HM Armed Tender Chatham, 1788

HMS Discovery, 1789 Captain Vancouver

Santiago, 1775 - Spanish Frigate of Explorer Bruno de Hezeta

Lady Washington, 1787 - Original Sloop Rig

 

Link to comment
Share on other sites

As always it's nice to see your progress Dowmer. You do great work.

Lou

 

Build logs: Colonial sloop Providence 1/48th scale kit bashed from AL Independence

Currant builds:

Constructo Brigantine Sentinel (Union) (On hold)

Minicraft 1/350 Titanic (For the Admiral)

1/350 Heavy Cruiser USS Houston (Resin)

Currant research/scratchbuild:

Schooner USS Lanikai/Hermes

Non ship build log:

1/35th UH-1H Huey

 

Link to comment
Share on other sites

Thanks Lou for dropping in.  It’s always nice to hear from you. 

 

I decided to rig the bowsprit and traveler.  I made the traveler out of wire provided in the kit and attached the jib halyard with the small single block and hook.  At this scale the hook is tiny, but I was able to mouse the end of the hook to keep it secure as it would have been done.  I know, I have a sickness.  😃

 

 

14D6C6F2-83EC-447E-89C4-102D068B0B73.thumb.jpeg.306c9b8f75744bc395b15ee0603a369a.jpeg

 

The outhaul was rigged and passed through the sheeve on the end of the bowsprit then through the block on the stem and up into the bow to be secured to the forward thwart with the support knees.  With the outhaul acting like a bobstay the bowsprit is surprisingly steady. 

 

 

94E683D8-9C14-469F-9B6E-B8189E5CD07F.jpeg.e3e27df8447ec66da2953ecc5bac1f1c.jpeg

 

 

On to the boom and gaff after the holiday weekend.

 

 

 

 

 

 

 

 

Able bodied seaman, subject to the requirements of the service.

"I may very well sink, but I'm damned if I'll Strike!" JPJ

 

My Pacific Northwest Discovery Series:

On the slipways in the lumberyard

Union, 1792 - 1:48 scale - POF Scratch build

18th Century Longboat - circa 1790 as used in the PNW fur trade - FINISHED

 

Future Builds (Wish List)

Columbia Redidiva, 1787

HM Armed Tender Chatham, 1788

HMS Discovery, 1789 Captain Vancouver

Santiago, 1775 - Spanish Frigate of Explorer Bruno de Hezeta

Lady Washington, 1787 - Original Sloop Rig

 

Link to comment
Share on other sites

Thanks Chuck, all your work inspired my build. I appreciate that you make these kits available. 

 

 

 

 

 

 

Able bodied seaman, subject to the requirements of the service.

"I may very well sink, but I'm damned if I'll Strike!" JPJ

 

My Pacific Northwest Discovery Series:

On the slipways in the lumberyard

Union, 1792 - 1:48 scale - POF Scratch build

18th Century Longboat - circa 1790 as used in the PNW fur trade - FINISHED

 

Future Builds (Wish List)

Columbia Redidiva, 1787

HM Armed Tender Chatham, 1788

HMS Discovery, 1789 Captain Vancouver

Santiago, 1775 - Spanish Frigate of Explorer Bruno de Hezeta

Lady Washington, 1787 - Original Sloop Rig

 

Link to comment
Share on other sites

Robert,

Thanks for the kind comments. I'm working on the last of the running gear and should have it completed soon. 

 

Cheers,

 

 

 

 

 

 

Able bodied seaman, subject to the requirements of the service.

"I may very well sink, but I'm damned if I'll Strike!" JPJ

 

My Pacific Northwest Discovery Series:

On the slipways in the lumberyard

Union, 1792 - 1:48 scale - POF Scratch build

18th Century Longboat - circa 1790 as used in the PNW fur trade - FINISHED

 

Future Builds (Wish List)

Columbia Redidiva, 1787

HM Armed Tender Chatham, 1788

HMS Discovery, 1789 Captain Vancouver

Santiago, 1775 - Spanish Frigate of Explorer Bruno de Hezeta

Lady Washington, 1787 - Original Sloop Rig

 

Link to comment
Share on other sites

So I needed a flag but I needed to figure out how they attached the flag to the halyard. After a lot of searching around I referred to an old Jean Boudriot book and found a depiction of one in his book of the BonHomme Richard. 

Im assuming this is how they typically secured them and it makes sense.  

 

96F931E4-9FAE-4FA4-BDE5-59E3147DBB29.thumb.jpeg.d27b164ae91ced9f8e18530cbc372165.jpeg

 

 

The period is correct so I gave it a try.  The hardest thing to make was the toggles.  At this scale they were about a mere 1.5mm.  I turned down a piece of hardwood and wrapped the .008 rigging line around it. The Hoist of the flag (the vertical part) was left white and folded over the line and glued with thinned white glue.

 

The flag was made using Chuck’s method of tissue paper.  Here’s a link to his thread for the Cheerful. Cheerful Link

 

I chose a 13 star flag representative of the era circa 1790.  I used some some tissue paper the wife had squirreled away for Christmas.  Cut a small piece and taped it onto a sheet of 8x11.5 office paper. This acted as a carrier to feed the tissue through the printer.  Printed the flag then cut it to shape and sprayed some Krylon fixative. After gluing in the toggles I sprayed some more fixative on the flag to soften it and shaped it.  Viola La!

 

I attached the halyards and hoisted the flag to the truck.  Secured to the starboard deadeye.  Here’s some pictures of the finished product.  Making and attaching the toggles was fiddly but worth it in the end.

 

 

70463786-5767-46F0-9C4F-CFA781289251.thumb.jpeg.39cf7f72c3ce8c93f472d9c9a7354fd5.jpeg

 

 

9896584E-9D53-47A8-83B9-71E149CFC8FD.thumb.jpeg.050de3624451c375a6e636d875e0f06e.jpeg

 

 

 

42A1D728-01A2-4BA3-9C4D-EC0E43B806CB.thumb.jpeg.7ee42d867f9e4c0fb060eabcbd4c7660.jpeg

 

 

 

766EA9B2-1904-47B5-90F6-7DCADCAC0A81.thumb.jpeg.7f996ee9cc37909c842b945b5f872558.jpeg

 

 

Next up is to make some rope coils and hang them on the boat and I’m done. 

 

 

Cheers landlubbers 😁

 

 

 

 

 

 

Able bodied seaman, subject to the requirements of the service.

"I may very well sink, but I'm damned if I'll Strike!" JPJ

 

My Pacific Northwest Discovery Series:

On the slipways in the lumberyard

Union, 1792 - 1:48 scale - POF Scratch build

18th Century Longboat - circa 1790 as used in the PNW fur trade - FINISHED

 

Future Builds (Wish List)

Columbia Redidiva, 1787

HM Armed Tender Chatham, 1788

HMS Discovery, 1789 Captain Vancouver

Santiago, 1775 - Spanish Frigate of Explorer Bruno de Hezeta

Lady Washington, 1787 - Original Sloop Rig

 

Link to comment
Share on other sites

Great work Dowmer.

This is going to make a great addition to your growing PNW fleet. Looking forward to seeing it in person someday.

Lou

 

Build logs: Colonial sloop Providence 1/48th scale kit bashed from AL Independence

Currant builds:

Constructo Brigantine Sentinel (Union) (On hold)

Minicraft 1/350 Titanic (For the Admiral)

1/350 Heavy Cruiser USS Houston (Resin)

Currant research/scratchbuild:

Schooner USS Lanikai/Hermes

Non ship build log:

1/35th UH-1H Huey

 

Link to comment
Share on other sites

Thanks Lou, great to hear from you.  This little project was something to wet my appetite to get back into ship building.  It did its job. 😀 I'm really enjoying it.

 

The best part is learning all the different and new techniques on this website.  Over course the motivation aspect of seeing all the incredible work by the masters here help as well.  I wish I had this resource when I started 30 years ago.  It would have prevented a lot of head scratching.  😟

 

 

 

 

 

 

Able bodied seaman, subject to the requirements of the service.

"I may very well sink, but I'm damned if I'll Strike!" JPJ

 

My Pacific Northwest Discovery Series:

On the slipways in the lumberyard

Union, 1792 - 1:48 scale - POF Scratch build

18th Century Longboat - circa 1790 as used in the PNW fur trade - FINISHED

 

Future Builds (Wish List)

Columbia Redidiva, 1787

HM Armed Tender Chatham, 1788

HMS Discovery, 1789 Captain Vancouver

Santiago, 1775 - Spanish Frigate of Explorer Bruno de Hezeta

Lady Washington, 1787 - Original Sloop Rig

 

Link to comment
Share on other sites

6 hours ago, Dowmer said:

I wish I had this resource when I started 30 years ago.

I do also, but in all truth based on recent work of mine, I would still just be able to sit and drool over the work performed by you guys with real talent and skill. But that is enjoyable as well so not all is lost.

Lou

 

Build logs: Colonial sloop Providence 1/48th scale kit bashed from AL Independence

Currant builds:

Constructo Brigantine Sentinel (Union) (On hold)

Minicraft 1/350 Titanic (For the Admiral)

1/350 Heavy Cruiser USS Houston (Resin)

Currant research/scratchbuild:

Schooner USS Lanikai/Hermes

Non ship build log:

1/35th UH-1H Huey

 

Link to comment
Share on other sites

Dave, thanks for dropping in to my thread.

I’m glad you appreciate the nuances of the PNW longboat from the standard kit.   👍

 

 

 

Able bodied seaman, subject to the requirements of the service.

"I may very well sink, but I'm damned if I'll Strike!" JPJ

 

My Pacific Northwest Discovery Series:

On the slipways in the lumberyard

Union, 1792 - 1:48 scale - POF Scratch build

18th Century Longboat - circa 1790 as used in the PNW fur trade - FINISHED

 

Future Builds (Wish List)

Columbia Redidiva, 1787

HM Armed Tender Chatham, 1788

HMS Discovery, 1789 Captain Vancouver

Santiago, 1775 - Spanish Frigate of Explorer Bruno de Hezeta

Lady Washington, 1787 - Original Sloop Rig

 

Link to comment
Share on other sites

The build is essentially finished.  I ordered a custom acrylic case to put it in.  Once it arrives I'll show the final result.  Thanks for all those that have followed this short little build.

 

Jason

 

 

 

Able bodied seaman, subject to the requirements of the service.

"I may very well sink, but I'm damned if I'll Strike!" JPJ

 

My Pacific Northwest Discovery Series:

On the slipways in the lumberyard

Union, 1792 - 1:48 scale - POF Scratch build

18th Century Longboat - circa 1790 as used in the PNW fur trade - FINISHED

 

Future Builds (Wish List)

Columbia Redidiva, 1787

HM Armed Tender Chatham, 1788

HMS Discovery, 1789 Captain Vancouver

Santiago, 1775 - Spanish Frigate of Explorer Bruno de Hezeta

Lady Washington, 1787 - Original Sloop Rig

 

Link to comment
Share on other sites

I am glad for you Jason in finishing your fine build, but at the same time I will miss it. What in on your list next?

Lou

 

Build logs: Colonial sloop Providence 1/48th scale kit bashed from AL Independence

Currant builds:

Constructo Brigantine Sentinel (Union) (On hold)

Minicraft 1/350 Titanic (For the Admiral)

1/350 Heavy Cruiser USS Houston (Resin)

Currant research/scratchbuild:

Schooner USS Lanikai/Hermes

Non ship build log:

1/35th UH-1H Huey

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...