Jump to content
bartley

HM Cutter Cheerful 1806 by bartley - 1/48 scale

Recommended Posts

After a false start in which I snapped off the bow extension when removing the bulkhead former from the sheet!  Things seem to be going well now.  The two sections of the bulkhead former were glued together and the rabbet strip glued in place.

Keel&FalseKeel.jpg

The stem pieces and the keel  were sanded on their faces to remove laser car but the edges were left unsanded.  The treenails were simulated as described by chuck using a 0.5 mm drill and filling with neutral filler.  After a coat of wipe-on-polly they were glued to the bulkhead former and fitted well with out the need for fettling.

Keel_Bulkhead-former.jpg

As recommended by Chuck no laser char was remove from the bulkheads and all fitted firmly.  Care was taken to retain each one square in all directions.

Stage2a.jpg

The bow and port filler blocks are added.

Stage3.jpg

Next comes, for me, the challenging process of fairing the hull correctly

 

Stage-4.jpg

I think I have a way to go yet but trial battens are beginning to look close. I am taking a rest now.  I think patience is the key here I am a little concerned about taking too much of the stern as others report it getting too narrow here.

 

John

Edited by bartley

Share this post


Link to post
Share on other sites

Yes, Griphos, this is the boxwood kit.  Bought a while ago when boxwood was cheaper than it is now!

 

John

Share this post


Link to post
Share on other sites

Hi John,nice to see another Cheerful being started. Blue Ensign has an excellent build log in the kit build log forum here on MSW. My own build is almost finished,scratched except for the windlass and guns. I will be following your build also.

 

Dave :dancetl6:

Share this post


Link to post
Share on other sites

Thanks, Chuck.  I have done another morning's fairing now.  When I think its done I will post another photo.

 

John

Share this post


Link to post
Share on other sites

Unfortunately there are lots of photos of this step but obviously good planking depends on this step being correct.

 

 

Fairing.jpg

 

 

Fairing2.jpg

Test battens seem to sit flat on most bulkheads but it is a bit proud at the bow.  So I thought I needed to take bit more of the marked bulkheads.

Bow.jpg

Obviously it is difficult to see how good (or bad) this is without seeing the actual model but this is the best I can do at this distance

 

Edited by bartley

Share this post


Link to post
Share on other sites

Post 4

 

I have now finished the Gun-port linings.  I used the method recommended by Chuck using a batten to obtain  smooth curve.  Although I eyeballed  the port and starboard battens to make sure they were the same.  I also double checked by using a level as here:

Stage-6a.jpg

Edited by bartley

Share this post


Link to post
Share on other sites

A word of warning.

 

Chuck warns about this later with respect to the stern ports but it is also important to make sure that all the gun-port sills fit snugly.  If they are a fraction long they will push the bulkheads out of square and negate all of your careful fairing because it changes the angle.  This happened on a couple of mine but fortunately I noticed the bulkhead move  and so took a little off the sill in question.  It doesn't take much.

 

John

Share this post


Link to post
Share on other sites

Stage-9.thumb.jpg.ebd123d7dd5bdb77e3c87604508cb3c7.jpg

Post 5

 

Framing the Stern

 

Following Chuck's suggestions, I first glued in the main outer frames (z)

Stage-7.jpg

Then the outer frames themselves (zz) are glued to these:

Stage-7a.jpg

And the whole assembly faired to match the hull:

Stage-7b.jpg

Stage-8.jpg

After installing the central frames, the gun-port sills and lintels were installed.  As reported by others, I found this step surprisingly tricky and I had to un-glue and reinstall several times!  I used a level and a sized block to ensure that each was level with the waterline and sized the same:

 

 

Stage-9.jpg

Here is the result

 

 

Stage-10a_Small.jpg

Stage-10_small.jpg

Edited by bartley

Share this post


Link to post
Share on other sites
On 2/21/2019 at 11:13 AM, bartley said:

Stage-9.thumb.jpg.ebd123d7dd5bdb77e3c87604508cb3c7.jpgPost 5

 

Framing the Stern

 

Following Chuck's suggestions, I first glued in the main outer frames (z)

Stage-7.jpg

Then the outer frames themselves (zz) are glued to these:

Stage-7a.jpg

And the whole assembly faired to match the hull:

Stage-7b.jpg

Stage-8.jpg

After installing the central frames, the gun-port sills and lintels were installed.  As reported by others, I found this step surprisingly tricky and I had to un-glue and reinstall several times!  I used a level and a sized block to ensure that each was level with the waterline and sized the same:

 

 

Stage-9.jpg

Here is the result

 

 

 

 

Stage-10a_Small.jpg

Stage-10_small.jpg

Post 9

 

Wales and Molding Strip

 

Stage 13a.jpg

Share this post


Link to post
Share on other sites

very nice!!  That is exactly how it should look at this stage.  Well done.

Share this post


Link to post
Share on other sites

Post 10

 

Planking above the wales

 

Planking up to the Molding strip was straight forward:Stage14.jpg.2abe3df618b36390958adca14de4e6ed.jpg

However planking around the gun-ports was tricky (for me at least) and took some time. However it is a nice little feature once done

Previous builds have involved continuous planking up to the sheer and then cutting the gunports into those planks an lining afterwards,  Chuck suggest that the rabbet should be 1/64 ‘’.  This is 0.39 mm.  I was not confident I could do this consistently so I made mine 0.5 mm.  I also found that for the fairly constant gaps amidships pre-making a set of planks  helped me to get the rabbet parallel to the port.  This is not my idea and I must  thank Rafine for the suggestion:

617011376_PlankStack.jpg.0211d4061b1044282f86da47342cdf8a.jpg

So here is the result:

1857189706_Stage15.jpg.936dd8e20911b2b4e03d69c49e513afb.jpg

Stage15a.jpg

Share this post


Link to post
Share on other sites

Chuck,

 

I obviously need to sand this back quite a bit to level up the planks but I am not sure how aggressive I can be here.  I am used to double planking where a bit of bog can be used to help but this is a new world.  I guess 3/64 is quite thick and any deviations are only a few thou.

 

John

Share this post


Link to post
Share on other sites

We are heading "state-side" next week so this build will be on hold for a while.

 

 

Share this post


Link to post
Share on other sites
Posted (edited)

Chuck,

 

I have been experimenting with some treenailing above the wales.  I have a couple of questions>

 

Between the bulkheads I find I am drilling right thru the plank.  Presumably this is Ok since it will be covered by the bulwark planking?

 

Secondly: How do you avoid filling the caulking line between the planks?

Edited by bartley

Share this post


Link to post
Share on other sites
Posted (edited)

Post 13

 

Chuck suggests adding the second layer to the Wales at this stage. However, others on the site have suggesting added the next two layers of planking first and so I adopted this course of action.  I found the drop plank a bit tricky to fit but after several paper patterns I developed a better understanding of what the shape should and I am now satisfied with the fit.

 

 

 

MG_4009.jpg

MG_4008.jpg

Edited by bartley

Share this post


Link to post
Share on other sites
Posted (edited)

Post 14

Finishing the wales.

 

The second layer of the wales was added and painted black.  I painted the edges first as I was not confident that I could do this afterwards and not get paint on the planking.

 

_MG_4017.jpg

2019-05.jpg

Edited by bartley

Share this post


Link to post
Share on other sites

Post 15

Lining out the hull. 

I did this several times but in the end the difference between the various versions was only around 0.5mm.  There seems to be no tapering required aft of about bulkhead B.  I hope this is correct!

_MG_4027.jpg

_MG_4030.jpg

_MG_4034.jpg

_MG_4036.jpg

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Recently Browsing   0 members

    No registered users viewing this page.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem

Modelshipworld - Advancing Ship Modeling through Research
×
×
  • Create New...