Jump to content

HMS Victory 1737 by Ekis - FINISHED - Artesania Latina - Scale: 1:84 - inspired by the Victory of 1737


Recommended Posts

I'm doing this thread on the HMS Victory which is the current project.
I've made good progress on construction, but I'm going to put the construction steps here and let it react before posting the next ones.
All texts are those of a French forum, simply translated by Google Translate. Excuse me in advance for grammatical mistakes or syntax ...

(2016, December)
I have the Artesiana Latina kit at 1/84.
The skeleton is mounted, I must attack the hull. This boat once mounted must be about 1m25: big bug!
But before plunging headlong into curling for a very long time, I do as usual, a pause to think about what I want, what is done, how to tint, mount, etc ...


pc270010.jpg

pc280016.jpg

pc280012.jpg

pc280014.jpg

pc280013.jpg

For this, I gather a large library of models, photos of Victory, various docs. In the kit, no plan to scale, but a dvd and prints format A3. It bothers me a little not to "see" it in real size ...
Moreover, I saw many Victory perfectly realized ... it does not interest me to remake!

These two facts pushed me to wonder about this boat. I looked for a monograph close to the scale, I just ordered the monograph of the Superb at the AAMM (Association of Friends of the Navy Museum): a 74 french guns of the 18th.

Conclusion: I will not do the real HMS Victory!  :)
But I will use this base to make a three masts of the eighteenth ... I will choose my colors and shades, change the castle, adapt a balcony or 2, perhaps redo bottles, adapt the kit in fact.
I am going to make MY model respecting the historical codes, but not a copy of this ship.
Of course, I will use the elements of the kit, but I will extrapolate according to my desires.

In short, we'll see!


Here is the end of sanding couples and keel (a long time to do everything clean), gluing the whole and a first bridge just screwed to maintain properly and check the squareness (2 couples deformed on the top, but nothing irrattrapable).
I have a little attacked the sanding to border, but this step will be long, I will be very careful and take my time. It's so important to place strakes next.

p1010010.jpg

p1010013.jpg

p1010012.jpg

p1010011.jpg

Link to comment
Share on other sites

And when to think about the future of this boat, would not it be more fun to try this kind of stuff for the castle, rather than the cheap decorations of Artesania Latina? :)
p6030012.jpg

 

p6030014.jpg

 

p6030015.jpg

 

Parallel to the curving and tedious editing of cannons, which are not yet of interest in photography, I advance on the design of the castle.
I'm starting from that (the wood pieces of the kit, around, it's my personal stock):

 

p6270012.jpg

 

I made a cardboard model to conceptualize the perspectives, the number of openings, the depths.
It will start from scratch or almost, add parts for the balconies, etc ... The parts of the kit just serving as a global template:

 

p6270010.jpg

 

p6270011.jpg

 

 

And with some tests of decorations that will have to harmonize with each other, and with the choices of wood, hues and moldings.
These are just essays, you have to make an effort of imagination to find a harmony, but it works:

 

p6270014.jpg

 

p6270013.jpg

 

There, there is more than to trace all that to own, millimeter, to postpone on wood, to cut, to pierce the openings, to realize the braces (!!), to make the moldings, to adjust, etc, etc ...

 

I simply recall that I am inspired by the Victory of 1737.
Making a copy or admiralty model does not interest me.
I want to respect the main lines, the main colors of 18th century shipbuilding, and give myself the freedom to create according to my desires.

I blackened and polished the 100 guns and all other hardware, I finished sanding couples to receive the first strakes. By the way, I will first make the works before gluing the lower deck, to have access to the whole of the hold and the hull. All this, unlike editing AL of course ...

The guns are mounted and more or less detailed depending on their visible locations or not. I will see at the time of their implementation what I detail or not (brague, trunnion, etc ...)
In any case, the 6 planned (maybe more, depending on the changes that I will make the assembly) on the upper deck.
I also want to do some weathering / aging on this boat, so many trials in progress, etc ...

 

p7140013.jpg

 

p8010010.jpg

 

p8010011.jpg

 

p7140010.jpg

 

p7140012.jpg

 

p7140011.jpg

 

By the way, so, I advance limply on the castle and the painting especially.

I made myself a model of paper cutting, a new general shape in ctp (repeated several times by changing thickness), new tests of decor more sober. In fact, in addition to balconies, I want gaps between the sides and the rounded part in the center, so it is necessary to put several layers, in short ... not simple, and especially very time-consuming!

I am at the dressing openings with frame and braces (brass for finesse), cutting floors for balconies ... rethink the planned system of attachment to the hull. A little head because it is also necessary to think of the oblique of the table and the bouges of bridges.

After come the wood decor, the dyes and paintings, then the metal decorations.

 

p6300010.jpg

 

p8010012.jpg

 

p8010013.jpg


Basically, except metal deco and wood chopsticks, it should have a contrast like this:

 

tablea10.jpg

 

The transom mounts slowly.
Parallel to the frames and braces of windows and doors, the structure of balconies related to bridges is practically made, the shell, in fact!
The pieces are all made, it will remain the assembly with the establishment of coatings, dyes and decorations.

 

p8050010.jpg

 

p8050011.jpg

 

p8120011.jpg

 

p8120010.jpg

 

p8120012.jpg

 

p8150010.jpg

 

p8150011.jpg

 

p8160011.jpg


Windows are made, 1st coat of paint.

 

p8140010.jpg

 

p8160012.jpg


The upper vault is clad in linden wood, the framing sharper. We will test the dye of this part.

 

p8160010.jpg

 

Next mission: make the plating of all parts.

 

Just 2 little things: decorate the balcony floors.

 

p8180011.jpg

 

p8180010.jpg

 

Things come to life: painting and first fitting windows. :)

 

p8300010.jpg

 

p8310011.jpg

 

p8310012.jpg

 

All parts of the assembly (the black transom, the balconies, the side walls, the ceilings) are bordered in boards of 3 or 5mm.

This is a flat mount to show the colors simply: the side walls are next. There, we have no depth.
There is also a lack of details in addition to the windows on the board: on the uprights at the bottom, between the windows, will come wooden columns for example. Or dressing rods under balcony windows, wooden sticks to dress the railings, etc ...

The decorations for this part were painted in 2 bronze paints (bright and old bronze), then aged with the bitumen of judée, like the sticks decorations brass of the balconies.

Well, it's just a color vision on the wood.
I like the contrast: it corresponds to what I had planned for the stern.

 

Continued assembly, gluing, tightening ...

 

p9050019.jpg

 

p9050016.jpg

 

p9050014.jpg

 

p9050013.jpg

 

p9050010.jpg

 

p9050011.jpg

 

p9050012.jpg

 


Then we stick and we tighten everything!
To be done in several phases to find all the curves: here the 1st.

 

p9050018.jpg

 

p9050015.jpg

 

p9050017.jpg

 

 

Here, I arrive quietly at the end of the stern.
Just for the pictures, I show a decorated side ... ;)

 

p9060013.jpg

 

p9060012.jpg

 

p9060011.jpg

 

p9060015.jpg

 

p9070010.jpg

 

p9070011.jpg

 

p9070013.jpg

 

p9070014.jpg


p9070017.jpg

 

p9070018.jpg

 

p9070016.jpg

 

p9070020.jpg

 

p9070015.jpg

 

p9070019.jpg

 

Well ... I had a taste of not finished.
I felt obliged to add molding on the right, on the left! :)

 

Some pictures :

 

p9110013.jpg

 

p9110015.jpg

 

p9110016.jpg

 

p9110010.jpg

 

p9110012.jpg

 

p9110011.jpg

 

p9110017.jpg

 

p9110014.jpg

 

The stern will be mounted later, when the hull will be made.
But this part helped me to see and determine the colors, the style for the whole ship.

 

 

Link to comment
Share on other sites

And now the assembly of the hull.
It is not sanded at all, since during assembly. I still have a good time!
After, it will be the piercing of the Gunports, and finally final sanding ... :)

 

pa100015.jpg

 

pa100013.jpg

 

pa100017.jpg

 

pa100016.jpg

 

pa100012.jpg

 

pa100010.jpg

 

 

I took care of the base. I had to do it before the hull was closed to pierce.
The brass rods fit 5 cm into the hull and the same into the wooden slab. It weighs this boat once finished!
Nothing is glued of course, it is necessary to sand the plate, tint a little, but at least the holes are made.

 

pa200013.jpg

 

pa200011.jpg

 

pa200010.jpg

 

pa200012.jpg

 

pa240010.jpg

 

pa240011.jpg

 

pa200014.jpg

 

pa240012.jpg

 

 

Just some picts to show the planking closely. It's my method, it can, perhaps, serve to beginners.

 

pa260011.jpg

 

pa260010.jpg

 

pa280010.jpg

 


I begin to see the end for the works! :)

 

pb130011.jpg

 

pb130010.jpg

 

pb130012.jpg

 

pb130014.jpg

 

pb130015.jpg

 

pb130016.jpg

 

pb130013.jpg


pb140011.jpg

 

pb140013.jpg

 

pb140014.jpg

 

pb140012.jpg

 

pb140010.jpg

 

I do my best, and it will not be perfect, far from it!
But I wanted to see if I knew how to model in a simple planking a hull of this size (about 80/90 cm)

It's boring, longer and more rigorous than a double planking (everything is visible!), But it's a kind of personal challenge ...

 

 

The hull ends, more than 2 strakes and I can move on ... Not unhappy to have completed this game. I spent the time needed!

 

pb220012.jpg

 

pb220013.jpg

 

pb220015.jpg

 

pb220010.jpg

 

 

This time, this hull is over.
The Sternpost and Knee of the Head are not glued. The inner bottom received a layer of glue / sawdust.
The keel is about 85cm long.

 

pb240019.jpg

 

pb240014.jpg

 

pb240012.jpg

 

pb240010.jpg

 

pb240015.jpg

 

pb240016.jpg

 

pb240017.jpg

 

pb240013.jpg

 

pb240011.jpg

 

pb240018.jpg

 

 

We go on to the following steps:
Manufacture of the Rudder with taper, blackening hardware (they seem oxidized, full of greyish green: it's normal! This ship will undergo an aging everywhere...


pb290011.jpg

 

pb290012.jpg

 

pb290010.jpg

 

Tracing and first cutting of Gunports on a series of 100 ... this series of guns is false, just to sting.


pb290013.jpg

 

pb290014.jpg

 

pb290017.jpg

 

pb290016.jpg

 

pb290015.jpg

 

 

Following the drilling of the Gunports.

 

pc010010.jpg

 

pc020010.jpg

 

pc020014.jpg

 

pc020015.jpg

 

pc020012.jpg

 

pc020013.jpg

 

pc020011.jpg

 

 

The lower deck is laid.

The supports of the false guns are also in place. To starboard, the support is moved backwards in order to be able to stick the guns, but also to close the gunports.
This ship will be in port side combat with open gunports.
The wall has been doubled to correctly place the interior frames of the ports.

 

pc040014.jpg

 

pc040015.jpg

 

For the second deck, I put some sleepers, supported by pillars and spars to stiffen. I will continue while the strakes stick ...

 

pc040012.jpg

 

pc040013.jpg

 

pc060010.jpg

 

pc060011.jpg

 

pc060012.jpg

 

 

That's it, this hull is done!
I spent this long step, but the result is rewarding. ;)

I wanted to show these views of the hull before the piercing of all ports, to realize why this is called a wall ...

The stern fits perfectly in its location, well embedded in the hull.
And now, the gunports, I'm going to break this hull of 75 holes!

 

pc110020.jpg

 

pc110019.jpg

 

pc110011.jpg

 

pc110010.jpg

 

pc110013.jpg

 

pc110018.jpg

 

pc110015.jpg

 

pc110012.jpg

 

pc110014.jpg

 

pc110016.jpg

 

pc110017.jpg

 

 

Tracing and drilling my gunports with a method to not screw up the perspective, using tape ...
Cutting with an x-acto and a small flexible metal ruler.

 

pc140010.jpg

 

pc140011.jpg

 

pc140013.jpg

 

pc140012.jpg

 

That's it, they are all pierced!

pc170111.jpg

 

pc170110.jpg

 

pc170116.jpg

 

pc170113.jpg

 

pc170115.jpg

 

pc170112.jpg

 

pc220110.jpg

 

pc220113.jpg

But it will be necessary to double the thickness of each opening of the hull inside to put the internal frames and to have a rabbet ... Otherwise, the Gunport Lids will not be able to close!

I am adapting each Gunport Lids and how to attach them to the hull, I must also make the frames of each gunport, and paste them after dyeing the hull ...
For drilling, it was necessary to predict the height of each deck to come. What has nothing to do with AL plans, in addition to my transformations!

Knowing that the guns will be in combat at port, gunport lids raised and tubes out and set back to starboard with gunport lids closed.

 

pc300011.jpg

 

 

I also worked in the form of the quarter galleries, since the stern does not correspond to the kit anymore: I have an extra quarterdeck (that will be 6 decks in all!), And the wales must correspond to the same perspective of the whole front and back, suddenly.

And an access door has been added, closed side to port, open (with future command ladder) to starboard.

 

pc300010.jpg

 

pc220112.jpg

 

pc220111.jpg

 

I also worked in the form of the quarter galleries, since the stern does not correspond to the kit anymore: I have an extra quarterdeck (that will be 6 decks in all!), And the wales must correspond to the same perspective of the whole front and back, suddenly.

And an access door has been added, closed side to port, open (with future command ladder) to starboard.
I have a blueprint (1699) that shows this kind of openness. It's part of my personal choices.

 

echell10.jpg

 

 

The color code of the ship is ok: I will be able to tint this hull! But not before having finalized the wales.


pc300012.jpg


And to change a bit, I finalized the head platform. And to match the architecture of the Victory of 1737, I have to add a focsle deck.

 

pc240110.jpg

 

pc300013.jpg

 

p1010011.jpg

 

p1010012.jpg

 

p1010010.jpg

Link to comment
Share on other sites

To stay in the color code of the castle, I finalized the head.

p1020011.jpg

p1020010.jpg

 

Start of coloring of the hull:
The teak hue is not uniform voluntarily to appear more "used".

p1040010.jpg

p1050012.jpg

p1050010.jpg

p1050011.jpg

The top of the wall will be black. But the wales will change all the contrast with black for low and medium wales, and red or ocher for those, finer from the top. It will depend on what visually gives all the red frames of gunports. :)
Picts were made just after the laying of the colors ... The gloss has since disappeared!

 

After thinking, I thought that the headboard looked more like a contemporary floor than a deck of the eighteenth century.
So, erase and we start again!

before
p1020010.jpg

after
p1060010.jpg

p1060011.jpg

p1060012.jpg

p1060014.jpg


And in parallel, the frames of the ports ... Go for a hundred!

p1060013.jpg

 

That's the final color code for this hull:

p1070011.jpg

p1160010.jpg

p1170010.jpg

p1170011.jpg

p1170012.jpg


The second deck was tinted (but not glued) with a trompe l'oeil slatted part behind the edge entrances, 2 shades to simulate the interior through the little space left by the guns, once in place. The white traces are made to simulate the wear of the hue with the rolling of the hulls ... Almost invisible also in the end, but in doubt, if it can offer nuances.

p1160011.jpg

p1160012.jpg

p1170013.jpg

p1170014.jpg

p1170015.jpg

 

The continuation of the wales and the bow a little more finalized.

The red wales take a lot of space visually, but all this will blend as and when the details of the hull: gunport lids, partial nailing, scuppers, etc ...

p1200010.jpg

p1200011.jpg

p1200012.jpg

p1210010.jpg

p1220012.jpg

p1220011.jpg

p1220010.jpg

 

The 18th is really in the middle of the exuberance and the multicolor charged with the 17th and the sobriety almost exclusively in black and white Empire ships and 19th in general ...
So red wales as the only colored element of the hull, a loaded stern and a bowsprit simpler than the eccentrics of the previous century, it seemed to me a good compromise ...

I take this opportunity to show what will look like the wall a little more finalized:

p1280011.jpg

p1280016.jpg

p1280012.jpg

p1280014.jpg

p1280013.jpg

p1280010.jpg

p1280015.jpg

 

Some photos with the rudder in place.

p2020011.jpg

p2020010.jpg

p2020012.jpg

p2020014.jpg

p2020015.jpg

p2020013.jpg

 

More picts of the Hull.
p2050010.jpg

p2050011.jpg

p2050012.jpg

p2050013.jpg

p2060013.jpg


The 2nd deck is also installed, the 2nd battery in progress:

p2060010.jpg


And I attack boarding ladder:

p2060012.jpg
p2060011.jpg

p2070010.jpg

p2070012.jpg

p2070011.jpg

 

The gunports lids under construction and the hull pulleys :

p2090010.jpg

p2090011.jpg

p2090012.jpg

p2100012.jpg

p2100013.jpg

p2100010.jpg

p2100011.jpg

 

An additional detail for this hull: Fenders or protections of the hull to raise the anchors way 18th. The upper part will be adjusted when the channels are in place.

p2110010.jpg

p2110013.jpg

p2110014.jpg

p2110012.jpg

 

Second battery made!

On the starboard side, back to battle, the main door and the back door are open and have been given a trompe l'oeil not to show an empty ship ...
Some guns are in low gear to counter a bypass; the rest of the port lids will be closed.

p2120013.jpg

p2120017.jpg

p2120018.jpg

p2120012.jpg

p2120011.jpg

p2120016.jpg

 

On the port side, in full line battle, all guns out, the main door is closed by a panel showing the color code of the boat.

p2120015.jpg

p2120010.jpg

p2120014.jpg


The finalization of the stern with the 4 ports of flight, closed gunport lids and rudder backup tips.

p2120019.jpg

p2120020.jpg

 

I show you the framework of the 3rd deck. A little work beyond the kit to support all this with props and addition of some sleepers to overcome the voids created by the holes of gratings to come or passage of the masts.

This is not the big carpentry, I rather recovered some used chopsticks. The goal is to get a deck without elasticity, the frame becoming totally invisible!

p2140012.jpg

p2140013.jpg

p2140011.jpg

p2140010.jpg

 

I worked on the head. Not really a party of pleasure because it was necessary to retouch a lot of stuff ...
I also redone the upper head rails to have the desired thickness and the ability to carve a little.
I will finalize the piece towards the catheads later.

p2160012.jpg

p2160013.jpg

p2160011.jpg

p2160010.jpg

p2170010.jpg

p2190013.jpg

p2190011.jpg

p2190010.jpg

p2190012.jpg

 

The head has received his grating ... and his toilet!
Side decors are also in place.

p2200010.jpg

p2210012.jpg

p2210010.jpg

p2210014.jpg

p2220010.jpg

p2210011.jpg

p2210013.jpg

 

Apart from the descent of the cathead later, the head is made. The knightheads have been added with their reinforced base, some decorations on the bowsprit, headtimbers.

p2230010.jpg

p2230013.jpg

p2230011.jpg

p2230012.jpg

 

I'm on the 3rd deck.
It is necessary to planking, to put the guns, to rig some, to create and to place the gratings with and without stairs, etc ...

p2250010.jpg

p2250011.jpg


You also have to put some decor for the descents of stairs on the 2nd deck.

p2280010.jpg

p2280011.jpg


p2280015.jpg


For my part, I am not the planned editing, but an earlier version (1737 and / or 1765).
The 4th deck is different from the Victory of 1765: the pit is longer, the gangways narrower, the main mast is not integrated into the upper deck.

p2280012.jpg

p2280014.jpg

p2280013.jpg

Link to comment
Share on other sites

The 3rd deck is being dressed.
The full upper deck is yet to come, plus the forecastle at the bow, the quarterdeck and the poop at the rear.

The central street is slatted in walnut stained rosewood, edged with ebony rods, the rest in limewood (under construction). The walling of the wall was done and painted in red, the mooring rings of the guns laid. The surfacing will continue upward with the 4th deck.
The base of the main mast is also manufactured.

A last look at the lower decorations (partially visible through the doors and stairs):

p3010010.jpg

p3010011.jpg

p3010012.jpg


Laying the planking:

p3040011.jpg

p3040010.jpg

p3040012.jpg


Mast base:

p3060010.jpg

 

That's it, this deck is slatted, aging included with more "worn out" areas under the guns, stairs and downhill as well. Not easy to restore that in artificial light and photos.
Now I go to the guns rigging and stair railing.

p3080013.jpg

p3080014.jpg

p3080012.jpg

p3080011.jpg

p3090011.jpg

p3090010.jpg

p3090012.jpg

p3090014.jpg

p3090015.jpg

p3090013.jpg

 

Before the installation and the rigging of all the guns of this battery of the 3rd deck, I anticipate a little and I foresee the pose of the 4th deck.
It was also necessary to manufacture the passage of the mast for this future deck: the support which rests on the 3rd ...

p3110011.jpg

p3110010.jpg

 

p3120017.jpg

p3120016.jpg

p3120010.jpg

p3120013.jpg

p3120012.jpg

 

p3120015.jpg

p3120011.jpg

p3120014.jpg

 

Partition of the kitchen made with the quarter bench.

p3160015.jpg

p3160014.jpg

p3160011.jpg

p3160012.jpg

p3160016.jpg

p3160010.jpg

p3160013.jpg

 

3rd deck finished.
The guns are rigged in combat or not according to the edge, the elements of decoration in place (balls, barrels, crates, various ropes, etc ...), the columns intended to receive the leases under the boats, the kitchen with its roof copper and chimney, ladders and stairs.


p3210010.jpg

p3210011.jpg

p3230011.jpg

p3230010.jpg

p3240010.jpg

p3240012.jpg

p3240011.jpg

p3240014.jpg

p3240013.jpg

p3240015.jpg

p3240016.jpg

 


I will be able to attack the 4th deck ... it will go in the personal creation !!

p3250011.jpg

p3250012.jpg

p3250010.jpg

p3220013.jpg

p3220012.jpg

p3220010.jpg

p3220011.jpg

 

The 4th deck is almost planked, the rest with the identical central street lined with ebony.
The spirketting is made and painted in red.
The kitchen and back gratings are made. The rear receives a 2nd capstan with its bars (for the decor).
The wheelhouse will be in checkerboard wood 2 shades (to recall the floors of galleries), framed by the walls of the officers' cabins. A little game of patience to realize that ...
Finally, the stearing gear (double wheels) will be behind the mizzen mast, unlike the restored Victory of 1805, but according to the ships of the early eighteenth.

p3290010.jpg

p3290014.jpg

p3290013.jpg

p3290011.jpg

p3290012.jpg

p3300012.jpg

p3300011.jpg

p3300010.jpg

p4020011.jpg

p4020010.jpg

p4020012.jpg

p4030011.jpg

p4030010.jpg

 

Small advance on the focsle and the upper part at the front:

p4050010.jpg

p4050013.jpg

p4050011.jpg

p4050012.jpg

p4070010.jpg

p4070012.jpg

 

The 2 pumps around the main mast are in place,

p4070011.jpg

p4070014.jpg


Various crates should also find a place either under the focsle or on the deck ...

p4070013.jpg

 

While waiting for me to take over the rear decks, here is the forecastle finished.
Trompe-l'oeil decor made of crates, barrels, barrel and car ...

p4080011.jpg


Support frame made of chopsticks recovery

p4080010.jpg


The foclse has been aged as the rest before receiving the foot of mast, carronades, racks, etc ...

p4090010.jpg

p4090014.jpg

p4090012.jpg

p4090011.jpg

I asked myself if I made windows at this place, but the channels will take up space, and this is the place where we go back anchors ... And then it is only a warehouse at the top of the ship.

Now, I will be able to finish the head with the catheads.

 

The stern is definitely stuck:

p4120015.jpg

p4120016.jpg

The wheelhouse pavement and officers' square is finished:

p4120012.jpg

The openings of the cabins are made:

p4120011.jpg

p4120010.jpg

I attack the structure of the square and in the center there will be the stearing gear.

p4120014.jpg

p4120013.jpg

 

p4130013.jpg

p4130015.jpg

p4130014.jpg

p4130016.jpg

p4130017.jpg

p4130018.jpg


The following to do with the quarterdeck and poop to finish the levels ... Still a lot of work!

p4130019.jpg

p4130022.jpg

p4130020.jpg

p4130021.jpg

 

The decks are a little advanced, I want to finish the bulk of the main structure before tackling the various arrangements.
So the back of the boat was mounted with the wheelhouse, the quarter-deck. The aesthetic uses the same color and deco codes as the rest, with decks in the same colors, facades in small windows. The quarterdeck receive a skylight.
The openings on the wall have also received their frames.

I show you some pictures of all to see the floors. ;)

p4210012.jpg

p4210015.jpg

p4210017.jpg

p4210013.jpg

p4210010.jpg

p4210016.jpg

p4210011.jpg

p4210014.jpg

p4210018.jpg

 

Various arrangements on the decks.

p5050013.jpg

p5050011.jpg

p5050019.jpg

p5050010.jpg

p5050014.jpg

p5050017.jpg

p5050016.jpg

p5050012.jpg

p5050015.jpg

p5050018.jpg

 

suite
p5130010.jpg

p5130011.jpg

p5140017.jpg

p5140016.jpg

p5140015.jpg

p5140014.jpg

p5140011.jpg

p5140012.jpg

p5140010.jpg

p5140013.jpg

 

Another little piece of fact: the focsle with its 2 carronades.
After, the planksheers wait for me and I will work the first gunport lids closed side ... or I make the quarter galleries.

p5190018.jpg

p5190019.jpg

p5190017.jpg

p5190022.jpg

p5190020.jpg

p5190021.jpg

p5190023.jpg

 

Some close-ups, with all the flaws that shows, but too bad ...

p5200010.jpg

p5200016.jpg

p5200015.jpg

p5200011.jpg

p5200012.jpg

p5200018.jpg

p5200013.jpg

p5200017.jpg

p5200014.jpg


And finally, I attacked the quarter galleries !

p5240010.jpg

p5240011.jpg

p5240012.jpg

Link to comment
Share on other sites

The work on the stern and the quarter galleries continues, port finishes or almost.
I took the opportunity to finalize the ornamentation, put the catheads and drill the holes for the lanterns (not glued). These 3 lanterns seem very big for this boat. These are the lanterns of the Artesania Latina kit, but I'm going to check their scale before putting them on forever ...
All this corresponds almost to what I had in mind from the start, it is already a satisfaction!

p6020012.jpg

p6020017.jpg

p6020015.jpg

p6020013.jpg

p6020011.jpg

p6020014.jpg

p6020016.jpg

 

End of the assembly of the stern with the installation of the rail of the poop and deco of the galleries.

p6040010.jpg

p6030012.jpg

p6030010.jpg

p6030011.jpg

p6040012.jpg

p6040011.jpg


I took the opportunity to also stick the elements of the figurehead!

p6040013.jpg

p6040016.jpg

p6040014.jpg

 

Big work on the channels and the chain plates
Deadeyes and blocks are set up and stuck with the alignment of the future shrouds.


p6110010.jpg

p6110011.jpg

p6110012.jpg

p6110013.jpg

p6110014.jpg

p6140010.jpg

p6140011.jpg

p6140013.jpg

p6140012.jpg

p6140014.jpg

p6140015.jpg

p6140016.jpg

p6140017.jpg

p6140018.jpg

p6140019.jpg

p6140020.jpg

p6140021.jpg

p6140022.jpg

Voilà !!

 

And that's for the chain plates.
In fact, this part gave me a hard time!
I'm glad I finished that ...

p6230011.jpg

p6230010.jpg

p6230012.jpg

p6230013.jpg

p6230015.jpg

p6230014.jpg

p6230016.jpg

p6230018.jpg

p6230020.jpg

 

A 1st throw of gunport lids up ... closed or not to starboard ... (except some for the scenery)

p6240010.jpg


With the back door open on this side (the ladder will come later).

p6240011.jpg

p6240012.jpg


It going...
An attempt at provisional placement of the ladder:

p6250010.jpg  p6250011.jpg

p6250012.jpg

p6250013.jpg

p6250014.jpg

p6270010.jpg

p6270011.jpg

p6270012.jpg

p6270013.jpg

 

And here for port, all gunport lids open and canons out!

p6300010.jpg

p6300011.jpg

p6300012.jpg

p7010010.jpg

p6300014.jpg

p6300013.jpg

p7010011.jpg

p7010013.jpg

p7010012.jpg

p7010015.jpg

 

The hull is finished!


There will remain some odds as the rear catheads of each edge, but after the shrouds.
And now, the pedestal to decorate, the rowboats and the rigging ...

 

This subject is not quite up to date yet ...
Before I started rigging, I finished the base.
It is massive, I leave it a bit raw with just a dye identical to the hull on all 4 sides.
The 2 supports are in matt brass and blackened with a brass rod which enters 5 cm in the base and the hull, the central rod, passed to the browner, will be without support to lighten visually.
On the top, a matte black, a fine mahogany frame (3x0.5mm) and 4 corners figures reminiscent of the model's decor, just to remind the 18th. :)

Everything is very heavy, very stable for the weight of the model.

p7030011.jpg

p7030012.jpg

p7030010.jpg

p7030014.jpg

p7030015.jpg

p7030013.jpg

 

For ship's boats, I did not want to use the elements of Artesania Latina. The quality is mediocre and they are simple boats in zamac ...
By cons, Master Korabel kits are really good.
So, I looked at the website of Master Korabel (thanks Google translation), and I found a great seller in Moscow. I ordered without problem by Paypal and 10 days later, all the kits were at home. I took the opportunity to order 2 or 3 other things, but it will make other threads on the forum when I do them ...

I need 2 Launch (one on the deck and another with his masts along the hull).
2 barges for port and starboard aft and 1 on the deck
1 cutter for the cathts of the stern.

I did not find all these scales for the Victory, but I think it will be nice anyway ...


This is one of the launches in the colors of my Victory.

An extremely fine kit to assemble. Must be patient, rigorous, but at least it looks like a 20-seater canoe of the time ...
At my scale (1/84), the details are not bad. :)

p7040011.jpg

p7040012.jpg

p7040010.jpg

p7050011.jpg

p7050010.jpg

p7060010.jpg

p7060013.jpg

p7060012.jpg

p7060011.jpg

p7060014.jpg

p7060015.jpg


p7060017.jpg

p7060016.jpg

 

And the others...
They have all the colors of Victory, but distributed differently to identify them at sea.

p7150015.jpg

p7150014.jpg

p7240010.jpg

p7240012.jpg

p7240011.jpg

p7240013.jpg

p7240014.jpg

p7240015.jpg

p7240016.jpg


The whole series:

p8140011.jpg

p8140010.jpg

 

In addition, I ordered two small things printed in 3D in the Netherlands at the scale 1/84 to compare with what I had:
The Victory lanterns and the compass table.
Well it turns out that the lanterns of the kit are 2 times too big compared to the reality (which I suspected, the manufacturers optimize the parts between the kits ...), and the 3d printing also restores the perspective volume of the lantern.
So I will keep for another model the 4 lanterns AL and put those home Shapeways.

p8140012.jpg


The compass table that I made is also oversized ... I'll see to use it maybe on another boat with a corresponding scale.

p8140013.jpg

p8140014.jpg

p8140015.jpg

Link to comment
Share on other sites

Some views of the 3D compass table in place, the lanterns too.
The rowboats received some accessories. I could not resist, contrary to what I had decided: the boat that will be moored to the hull now has sails ...

p8280011.jpg

p8280010.jpg

p8280012.jpg


p8280015.jpg

p8280014.jpg

p8280013.jpg


p8280016.jpg

p8280017.jpg

p8280018.jpg

 

The masts are in progress, nothing is glued of course, it becomes difficult to make photos with this scale.
The rowboat will finally be independent and not glued to the hull! It hid too many things by putting it next ... :)

p9020010.jpg

p9070010.jpg

p9070011.jpg

p9070014.jpg

p9070012.jpg

p9070013.jpg

p9070015.jpg

 

Small suite on the masts. I only spent a limited time on the Victory. I was busy with other things ...
I focused on the foremast to determine the look of the mast. The others will follow, they are all cut, but it is necessary to dress them! :)

But first the end of the base of the sailing boat:

p9080010.jpg

p9080011.jpg

p9080012.jpg


And so the foremast and its hune (? in english) in construction and aging:

p9110010.jpg

p9110011.jpg

p9160010.jpg

p9160011.jpg

p9160012.jpg

p9180010.jpg

p9180012.jpg


And a set up to see what it will look like:

p9180013.jpg

p9180011.jpg

p9180014.jpg

 

Small continuation of the construction of the rigging. It takes a long time these things ...
I'm showing you just a few steps.

p9200010.jpg

p9200011.jpg

p9210010.jpg

p9220010.jpg

p9220011.jpg

p9230010.jpg

p9230011.jpg

p9230012.jpg

p9230013.jpg

 

Well, the 4 masts are made, I'll be able to equip them with various pulleys ...
On the mainmast, I added some spears for the boarding, just in case !! ;)


Of course, the high masts (topmast and topgallant ) are removable. The low masts will remain alone to mount the shrouds more easily ....
For the specialists, the latest details added later, like the balusters in front of the topmasts.
So inevitably, on the overall photos with the boat, nothing is aligned correctly.  ;)


img_2010.jpg

img_2013.jpg

img_2015.jpg

img_2016.jpg

img_2017.jpg

img_2019.jpg

img_2021.jpg

img_2020.jpg

img_2024.jpg

img_2026.jpg

img_2027.jpg

img_2025.jpg

img_2028.jpg

img_2029.jpg

 

The following rigging ...
Forcibly, will have to go into the details with all these ropes. But if it helps, then I show! :)

For now, I focus on the foremast to be sure of the look that it gives.
And first, before the shrouds, you have to prepare a little.

The return of the machines, especially the 1st to achieve all that.

pa140011.jpg

pa140010.jpg


Unlike what I did on La Flore choosing the colors of the strings, this time, I decided to do more in the traditional. Take only natural colored threads, and apply either a shade to simulate the tar, or go to aging ... some tests:

pa150010.jpg


Then, we move to the assembly of "some" pulleys and caliornes (those who hang under the hune):

pa130010.jpg

pa130011.jpg


Finally, big job with the guys and their alignments. Then dye in India ink to have shades, unlike a basic black thread.

pa150011.jpg

pa150012.jpg


Finally, a little extra with the manufacture of bowsprit racks.
This time, instead of cutting everything in a stick, I chose to paste 5 pulleys in series on a small band of 2x0.5 invisible. They will be glued to each side of the bridge bracket. After all, I have pulleys that are well made, so use it! :)

pa150013.jpg

 

Following with advancing on the bowsprit: most ropes are tinted or aged, but I'll see in the end if I have to harmonize a bit or not.
On this vessel, only one strut of the main mast descends on the bow, the false, finer strut wraps around the foremast.

The bowsprit racks are in place.
The editing of all this is a little tricky, especially because of the gateway ... :)

img_2030.jpg

pa190011.jpg

pa190010.jpg

pa190013.jpg

pa190012.jpg

pa190014.jpg

pa190016.jpg

pa190015.jpg

Link to comment
Share on other sites

Few new things to show: rigging this type of ship is long and repetitive. I do not have much time right now to move on, but it's progressing slowly ... So just a few close-ups for details.

pa220010.jpg

pa310011.jpg

pa310010.jpg

pa310012.jpg

pa310014.jpg

pa310013.jpg

pa310015.jpg

pa310017.jpg

pa310016.jpg

pa310018.jpg

pa310019.jpg

pa310020.jpg

 

Few comments, the photos speak for themselves: the Victory has hair growing!
More than a hundred shrouds to put in place ... it's a bit of a job. The props of the low masts are in place, the rear davits port and starboard too (but removable, it is simply to be certain of the passage of the stays).

pb150011.jpg

pb150012.jpg

pb150010.jpg

pb150013.jpg

pb150014.jpg

pb150015.jpg

pb150018.jpg

pb150016.jpg

pb150021.jpg

pb150019.jpg

pb150020.jpg


The next shipyard is already waiting for me: high masts, yards and sails ...
But the masts of hune and parrot have already received their pulleys and various other stays while waiting to be in place.

pb150022.jpg

 

Still tight shots. Things are moving forward, but nothing spectacular ...

The skiff in front of the castle, the nets were filled with more than 300 hammocks, the shrouds received their platforms.
And many little things that take time but do not jump in the eyes...
It is ultimately that all these details change a model, I think.

pb180011.jpg

pb180012.jpg

pb180010.jpg

pb260010.jpg

pb260012.jpg

pb260011.jpg

 


pb260013.jpg

pb260014.jpg

pb260015.jpg

pb260016.jpg


pb260019.jpg

pb260017.jpg

pb260018.jpg

 

 

After finishing the shrouds, I start the ratlines!

I have for a long time ... I also added the ladders (we do not see it very often on the models, but it was necessary to be able to climb somewhere ...)
:)

pc060010.jpg

pc060011.jpg

pc060012.jpg

pc060015.jpg

pc060013.jpg

pc060014.jpg

pc060016.jpg

All ropes used are tinted: either with indian ink for stays and shrouds, or with a mix of bitumen/turpentine for usual maneuvers and stays.
It allows to have nuances and not a uniform industrial color ... I like it!
Well, I must admit that I add annoying permanently on this boat voluntarily! 😛

 

I continue in the long and monotonous work of ratlines and preparation of shrouds ...These are just pictures of build.  ;)

pc220011.jpg

pc220012.jpg

pc220010.jpg

pc220015.jpg

pc220013.jpg

pc220014.jpg

pc220017.jpg

pc220016.jpg

pc220018.jpg

pc220019.jpg

 

I finished the hoists of the boats, not easy to do ... I planned a system of quick disassembly to dismount them easily as I did not advance the sails of forestay and the passage of all the descending maneuvers masts. Otherwise, my big fingers do not pass!

pc270015.jpg

pc270013.jpg

pc270014.jpg


The Victory will have to go down to the basement of the house to continue mounting the upper rigging. Otherwise, it does not pass the door of the attic ...
But in the meantime, I can still prepare things.
The next step is to prepare all the yards, cut them, paint them, mount the dozens of pulleys and other bits used for routine operations.
Besides, I would like a vessel with the sails carved. It is a difficult exercise, rather than stretching a deployed sail.

 

 

Until I took care of the yards and sails, I had to do the four main anchors ...
One of them is equipped with a net: it allowed when it was along the hull to have one or two sailors to do depth surveys without being hindered by the hull.

pc310010.jpg

pc310012.jpg

pc310011.jpg

p1020011.jpg

p1020010.jpg

pc310013.jpg

p1010011.jpg

p1010010.jpg

p1010012.jpg


And then, while I was there, a 2nd boat is mounted on an individual support. But this one has an anchor below. This is how they were moved farther away from the ship to anchor in a safer way.

The boat will be attached to the boat by the cable of the anchor and a mooring end with a hook.

p1020013.jpg

p1020012.jpg


And now, the last big yard with yards and sails!

 

Some views of the job in progress ... It is really a considerable time this type of rigging !!
I still have many, many hours to spend on it, but it goes at its own pace.
As a reminder, all the sails will be carved, which adds time to spend on each one so that it is presentable and relatively realistic (taking into account that I use the sails of the kit AL which are of a quality say more than medium ...). All the lines of each sail are to rethink from the plans to be able to moor them properly once folded. Speechless

p1160010.jpg

p1160011.jpg

p1160012.jpg

p1160014.jpg

p1160013.jpg

p1160015.jpg

p1160017.jpg

p1160018.jpg

p1160016.jpg

p1160019.jpg

p1160021.jpg

p1160020.jpg

 

Before I started assembling the sails on the yards, it was necessary to cut them correctly: it's done!
It remains to fix them, to prepare the ropes for each one ... and to put them on hold until the top of the rigging is in place.

p1210011.jpg

p1210010.jpg


But first, there were still and always details to finish ...
Set up the spritsail topsail,

p1210012.jpg


And all the ropes that pass through the bowsprit racks,

p1210013.jpg

Tarred canvas protection of rudder head,  

p1210014.jpg

rail with nets for the front platform:

p1220012.jpg

p1220011.jpg

p1220010.jpg


And finally, for fun, a 18th century buoy (image found in my archives to reproduce it):

p1210016.jpg

p1210015.jpg

That's it, and now I'm immersing myself in the rigging of the yards ...

 

It's a big job at the base, work on the octagonal part of the yards, aggravated by my choice to show these sails furrowed ... It is necessary to work the folds, to think the bolting otherwise for that seems realistic. I am obliged to put invisible threads to create gathers, etc ...

p1300010.jpg

p1300011.jpg

p1300012.jpg

p1300014.jpg

p1300013.jpg

 

I focus on each yard to prepare everything before building the top of the rig.

p2030012.jpg

p2030011.jpg

p2030010.jpg

 

Go, pulleys and ... ropes!
A few close-ups of the bowsprit, the rigging of the yards, the flag pole at the stern.

p2080011.jpg

p2080012.jpg

p2080010.jpg

p2080013.jpg

p2090010.jpg

p2090011.jpg

p2090014.jpg

p2090013.jpg

p2090012.jpg

p2090015.jpg


And then, finally, all yards rigged with high masts: a bunch of wires everywhere !!

p2120011.jpg

p2120010.jpg


Finally, again the stern ports finished with their string shutters.

p2130011.jpg


Now, I'm tackling the preparation of dozens of wraps on the toggles with all kinds of threads used. ;)

p2130012.jpg

p2130010.jpg

 

Here is the current status of the shipyard: ropes everywhere, the stays in progress (the 3rd floor of the masts is also to be done) ... I put the 1st of the 3 jibsails, the spancer (english?), and the rear flag.

p2260011.jpg

p2260010.jpg

p2260012.jpg

p2260014.jpg

p2260013.jpg

p2260015.jpg

p2260016.jpg

p2260018.jpg

p2260020.jpg

p2260019.jpg

p2260021.jpg

p2260022.jpg

p2260023.jpg


The following: the end of the stays and ropes all over with the installation of staysails.  :)

 

Some images of work on the site, with some ropes! Sorry for the background of the garage where I migrated to finish without worrying about the volume of the Victory to pass the doors (my workshop is usually in the attic)... :)

p3050010.jpg

p3080010.jpg

p3080011.jpg

p3080012.jpg

p3080013.jpg

p3080016.jpg

p3080015.jpg

p3140012.jpg

p3140010.jpg

p3140011.jpg

p3140015.jpg

p3140014.jpg

p3140017.jpg

p3140016.jpg

Link to comment
Share on other sites

Unbelievable work  - Stunning.:o

 

OC.

Current builds  


28mm  Battle of Waterloo   attack on La Haye Saint   Diorama.

1/700  HMS Hood   Flyhawk   with  PE, Resin  and Wood Decking.

 

 

 

Completed works.

 

Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic.

HMS Warspite Academy 1/350 plastic kit and wem parts.

HMS Trafalgar Airfix 1/350 submarine  plastic.

Black Pearl  1/72  Revell   with  pirate crew.

Revell  1/48  Mosquito  B IV

Eduard  1/48  Spitfire IX

ICM    1/48   Seafire Mk.III   Special Conversion

1/48  Kinetic  Sea Harrier  FRS1

Link to comment
Share on other sites

Very well done :imNotWorthy:

Regards, Patrick

 

Finished :  Soleil Royal Heller 1/100   Wasa Billing Boats   Bounty Revell 1/110 plastic (semi scratch)   Pelican / Golden Hind  1/45 scratch

Current build :  Mary Rose 1/50 scratch

Gallery Revell Bounty  Pelican/Golden hind 1/45 scratch

To do Prins Willem Corel, Le Tonnant Corel, Yacht d'Oro Corel, Thermopylae Sergal 

 

Shore leave,  non ship models build logs :  

ADGZ M35 funkwagen 1/72    Einhets Pkw. Kfz.2 and 4 1/72   Autoblinda AB40 1/72   122mm A-19 & 152mm ML-20 & 12.8cm Pak.44 {K8 1/2} 1/72   10.5cm Howitzer 16 on Mark. VI(e)  Centurion Mk.1 conversion   M29 Weasel 1/72     SAM6 1/72    T26 Finland  T26 TN 1/72  Autoprotetto S37 1/72     Opel Blitz buses 1/72  Boxer and MAN trucks 1/72   Hetzer38(t) Starr 1/72    

 

Si vis pacem, para bellum

 
 
Link to comment
Share on other sites

I have advanced quite a bit on the rigging ... There are still some ropes to tie on the right, on the left, the mizzen yard to put on, but this complicated rigging already has a good face! 🆒

40492340233_4816d6d28c_b.jpg

46543125185_a1f89cc811_b.jpg

40492345793_ba7f4850ce_b.jpg

46543127565_58967e2651_b.jpg

33582103548_103227561c_b.jpg

46543122795_5676921a62_b.jpg

47458376971_ccc26d05fd_b.jpg

47458378201_5f32d6bf35_b.jpg

32516641687_ff0293ee36_b.jpg

47458388191_c567dc0368_b.jpg

46735310604_117de6d3d0_b.jpg

47458386321_1f71efe476_b.jpg

47458384771_f33924a10b_b.jpg

46735305904_bdcf017646_c.jpg

47458379951_67e745b1ee_c.jpg

Link to comment
Share on other sites

Amazing work  - Just amazing   -  words escape me,    you must feel proud.

 

OC.

Current builds  


28mm  Battle of Waterloo   attack on La Haye Saint   Diorama.

1/700  HMS Hood   Flyhawk   with  PE, Resin  and Wood Decking.

 

 

 

Completed works.

 

Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic.

HMS Warspite Academy 1/350 plastic kit and wem parts.

HMS Trafalgar Airfix 1/350 submarine  plastic.

Black Pearl  1/72  Revell   with  pirate crew.

Revell  1/48  Mosquito  B IV

Eduard  1/48  Spitfire IX

ICM    1/48   Seafire Mk.III   Special Conversion

1/48  Kinetic  Sea Harrier  FRS1

Link to comment
Share on other sites

Well, as I get dangerously close to the end of this personnal Victory, I post a lot of photos !!  3830981954.gif
More photos of the set will come later. But for that, must I go into studio photos with lighting, clean background, etc ...


For the moment, it is-almost-end of construction (I still have a lot of windings of rope to put everywhere).

46757241784_82c117f379_c.jpg

47427690422_82573383c9_c.jpg

46757243994_e9c725dd8c_c.jpg

47480633721_f2445fe10a_c.jpg

47480634561_8022401eb0_c.jpg

47427691272_806fcaf7b0_c.jpg

47480635651_98ac9835da_c.jpg


I pierced the underside of the support, inserted 2 internal threaded rods to have the possibility of fixing from below with 2 nuts if necessary ...

47427691542_5017a50c2c_c.jpg

 

47480636121_384e2e17db_c.jpg

46757248824_a068ed08d2_c.jpg

46757250924_c939c0c88f_c.jpg

46757251644_0a0c7c738c_c.jpg

47480637461_866d2164f7_c.jpg

47427694012_689cb18518_c.jpg

Link to comment
Share on other sites

Some pictures a little more worked:

32547790327_d58891c504_c.jpg
Victory 1737 by Ekis_G, sur Flickr

47436830082_ca33b9c9f5_c.jpg

47489668311_15c96aa624_c.jpg

32547792667_2cd1bd2f72_c.jpg

32547793347_e94620be1c_c.jpg

32547792897_0f99c1c0e4_c.jpg

47436835332_a8f48caeb4_c.jpg

47436834682_d6b7fd4703_c.jpg

47436828122_76c3d7a9c6_c.jpg

40523735253_9bce9c3131.jpg

47436826622_ed563c6f73.jpg

47436825932_0e1dc9ca0f_o.jpg

47436835852_0ccacf97bb_o.jpg

32547792457_0f8b1b5440_o.jpg


A frigate like La Flore shows the monstrous dimension of the admiral ships of the time like the Victory ...
(same scale at 1:84)

32547789837_372e626e6f_c.jpg

47436828812_54bdab2fe2.jpg

Link to comment
Share on other sites

Very different ... and very, very beautiful. Well, done !!

CaptainSteve
Current Build:  HM Granado Bomb Vessel (Caldercraft)

My BathTub:    Queen Anne Barge (Syren Ship Models)       Log:  Queen Anne Barge (an build log)

                        Bounty Launch (Model Shipways)                 Log:  Bounty Launch by CaptainSteve
                        Apostol Felipe (OcCre)
                        HMS Victory (Constructo)
Check It Out:   The Kit-Basher's Guide to The Galaxy

Website:          The Life & Boats of CaptainSteve

Link to comment
Share on other sites

Just seen this build. Wow, flights of fancy, pimp my boat and such words come to mind. Love it. You have so many original ideas this has quite blown me away. I too am building a vessel where I didn’t want the finished article to look like a pristine out of the box kit and have tried to weather it a little. Your treatment of the running tackle and rigging is the sort of thing I want to do so I hope you will not mind me pinching your ideas. Awesome well done and I shall keep an eye out for any future builds. Thank you for sharing this with us.

Link to comment
Share on other sites

Wow, thanks for that great comment! 😉
I did my best to give maximum realism to this vessel, and with the small workshop that I have ... respecting the buildings of the 18th century.
Of course you can take any ideas you want: this is the concept of the forum! 😃

Link to comment
Share on other sites

Absolutely fantastic work!

     Current:         Emma C. Berry Lobster Smack-Model Shipways-1:32-1866

        Back on the shelf:    USS Essex- MS- "Old Yellow Box" Solid Hull  Wall Hanger (Half Hull)                                                                                                                                                                                              

   Completed:    18th Century Armed Longboat-MS 1/24

                          USN Picket Boat-MS 1864 1/24                                  

                          US Brig Syren by Sea Hoss- Model Shipways-1803

                          18th Century Carronade/Ship Section

                          Mayflower-Pilgrims Pride by Sea Hoss-Model Shipways-1620

                          18th Century Long Boat by Sea Hoss-Model Shipways

                          USS Constitution by Sea Hoss-Revel-Plastic

Link to comment
Share on other sites

  • 2 months later...

Very cool!  Excellent work!

Building: 1:64 HMS Revenge (Victory Models plans)

1:64 Cat Esther (17th Century Dutch Merchant Ships)
 

On the building slip: 1:72 French Ironclad Magenta (original shipyard plans)

 

On hold: 1:98 Mantua HMS Victory (kit bash), 1:96 Shipyard HMS Mercury

 

Favorite finished builds:  1:60 Sampang Good Fortune (Amati plans), 1:200 Orel Ironclad Solferino, 1:72 Schooner Hannah (Hahn plans), 1:72 Privateer Prince de Neufchatel (Chapelle plans), Model Shipways Sultana, Heller La Reale, Encore USS Olympia

 

Goal: Become better than I was yesterday

 

"The hardest part is deciding to try." - me

Link to comment
Share on other sites

  • 6 months later...

This is So so good  you should have this displayed in a ship museum  - I bet Greenwich  UK museum  would be interested.

 

OC.

Current builds  


28mm  Battle of Waterloo   attack on La Haye Saint   Diorama.

1/700  HMS Hood   Flyhawk   with  PE, Resin  and Wood Decking.

 

 

 

Completed works.

 

Dragon 1/700 HMS Edinburgh type 42 batch 3 Destroyer plastic.

HMS Warspite Academy 1/350 plastic kit and wem parts.

HMS Trafalgar Airfix 1/350 submarine  plastic.

Black Pearl  1/72  Revell   with  pirate crew.

Revell  1/48  Mosquito  B IV

Eduard  1/48  Spitfire IX

ICM    1/48   Seafire Mk.III   Special Conversion

1/48  Kinetic  Sea Harrier  FRS1

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...