Jump to content
G.L.

Day gaff sailing boat with center board by G.L. - scale 1/10 - SMALL

Recommended Posts

On 1/16/2020 at 10:27 PM, michael mott said:

Geert

"The only thing that I can mention to my defense is that the boat is not designed to sail on open sea, but in sheltered waters like on a river or on a lake and probably only in nice weather. In such conditions the force on the gaff will not be so heavy."

Thanks for your explanation of why you made it the way you did.

 

The actual physics of the arrangement in the drawing would still put a much greater strain on the Gaff regardless of the weather conditions. Please I hope you don't misunderstand my intention It is my opinion the whoever drew that arrangement likely was not a seasoned sailor. That does not detract from the superb model that you have built.

 

Michael

 

Michael,

 

This morning, I went through my library to watch to other drawings of open gaff sail boats. You are definitely right: The bridle has to be spread a lot wider. The rig plan as drawn by Mr Van Beylen is not good. There is no need to consult other experts, I will change the gaff in the way you suggest.

Thanks a lot for your advise.

Share this post


Link to post
Share on other sites
On 1/19/2020 at 7:07 PM, vaddoc said:

Well, the peak halyard indeed does look a bit odd. Two ways of looking at it. Either you follow exactly what the designer had in mind, or you change the rigging to suit your needs. After all it is your boat and in real life I think during the initial fitting and much more during the life of the boat, many changes take place. I d say rig it as you like! 

 

I was looking again at your photos, I think the vividly grained wood works incredibly well at this scale! The boat is alive, the more boring woods like pear and boxwood would not achieve this I think. Lovely!

 

On 1/20/2020 at 6:42 AM, mtaylor said:

A little spray starch and an iron and the sail will be shipshape. 

 

On 1/19/2020 at 10:49 PM, Moab said:

Looking good!...Moab

Much thanks for your reactions, Vaddoc, Mark and Moab

Share this post


Link to post
Share on other sites

This week I started with modifying the gaff accordingly to the expert advice of Michael.

351.jpg.e29c098b7f558d6053c68f6c46e655a5.jpg

Then I continue the work at the fore sail. Before starting to sew the main sail, I want to finish the fore sail. It will take a while because here are new skills that I yet have to learn.
Around the sail a bolt rope has to be sewn. In the corners are thimbles. I think that I have seen the method to make them in the log of the Jaciente of Aviamator. I use electrical end sleeves from which I remove the plastic part and saw them in small sheaves of about 3mm each.

352.thumb.JPG.7e061d012b69bd37380e07a04e69b74f.JPG

 

353.thumb.JPG.09c46314c07d46a74bf01eec2db4b46d.JPG

 

354.thumb.JPG.ab373bfda94eedce0bf2e083c458beb2.JPG

 

355.thumb.JPG.50a25694f0843749c7176adbf6b6f0d8.JPG

Then I open the edges a bit with the help of a punch.

356.thumb.JPG.feb65d7900f74d7157a5035331c3dbc2.JPG

And finally I weather the thimbles by soaking them a while in oxidant.

357.thumb.JPG.a0f735a3f6c7e47c89444318c7abda1f.JPG

Now it is again sewing work, this time not with the machine, but by hand. The thimble goes in the bolt rope at the clew. and the rest is sewing along the jib leach.

358.thumb.JPG.edc86b2763a736870ac84f910471da22.JPG

That is where I am at this moment.

359.thumb.JPG.99111b24946208f24c15aadfadfcb9d7.JPG

 

Thank you to follow

Thank you for the likes

Thank you for your constructive comments

 

Till next week

Edited by G.L.

Share this post


Link to post
Share on other sites

Looking good there my friend, I'm probably going to do sails for my dinghy too but fortunately my sails don't have a bolt rope to worry about.

 

I think the new position of the gaff span is much better, if you look at the pic of my full sized boat you can see where the span is and how it relates to the mast, gaff and halyard. I should have posted this earlier in the conversation.

 

20190925_114633.thumb.jpg.3cc2355d8244761a2c69ae603ccfd13d.jpg

Share this post


Link to post
Share on other sites
On 1/25/2020 at 12:46 PM, Bedford said:

Looking good there my friend, I'm probably going to do sails for my dinghy too but fortunately my sails don't have a bolt rope to worry about.

 

I think the new position of the gaff span is much better, if you look at the pic of my full sized boat you can see where the span is and how it relates to the mast, gaff and halyard. I should have posted this earlier in the conversation.

 

20190925_114633.thumb.jpg.3cc2355d8244761a2c69ae603ccfd13d.jpg

Steve, Your boat is a beauty. It must be a real pleasure to sail her. 

Share this post


Link to post
Share on other sites
On 1/25/2020 at 5:36 PM, michael mott said:

Nice proportions Steve, I like the way the gaff lines up with the forestay, It really shows the benefit of the gaff rigs versatility.

Michael

 

 

Seeing this picture of the Caroline. I am happy that I changed the gaff rigging thanks to your advise, Michael.

Share this post


Link to post
Share on other sites

This week I continued to work at the jib. Sewing the jib leach is very time consuming, it took most of the time this week.

360.thumb.JPG.f46c265f164a765af459544a4453e114.JPG

Pressing the needle through the 'canvas' goes very well but when it has to pass through the leach I have to use sometimes the pliers.

361.thumb.JPG.c4bc7a171d7c11f47708ed8b0ea084a9.JPG

Finally the whole jib is fit with the leach.

362.thumb.JPG.fa39a286a38b8a57db5dca8488359d49.JPG

The jib has one reef level. A thimble has to be inserted at the luff and at the leech side. I us a thick needle as a spike to make a hole for it. The I widen the hole with a pricker.

363.thumb.JPG.98ae2bbea099bc9f88153ca69a77da55.JPG

 

364.thumb.JPG.fe48efd3b564cd66ff18b55ae05816c6.JPG

In the hole comes a thimble.

365.thumb.JPG.bf5b5f1b27a358dc343612eaede35eed.JPG

And the job is finished with sewing a thread in and out around the thimble.

366.thumb.JPG.0154990bf3729b48c45d873c60c9157b.JPG

 

367.thumb.JPG.b7066525ef8d4eb7c48c10c74dace6aa.JPG

To make the reef points, I start with applying a bit of textile glue on the spots where the points have to come to prevent the canvas of fraying out.

368.thumb.JPG.28bc6c36c0414ba8f210ac8e0a667162.JPG

Then I prick the holes with a thick needle.

369.thumb.JPG.a1f0e00d6f9730ff9e5a81689da90286.JPG

 

370.thumb.JPG.76a9faf3992a83afb293b5f235399c2d.JPG

The reef lines are passed through the holes and fixed with a knot at each side of the sail.

371.thumb.JPG.15c615b6c19322e5e701280b3853c634.JPG

Now I hold the lines straight and soak them with a bit textile glue to hold them straight and prevent them of unraveling and cut the lines to equal length.

372.thumb.JPG.a72a05596a84bc8b88d8df24fb7e518f.JPG

 

373.thumb.JPG.a47d4d577f6069baa08afa3937b9968f.JPG

This is where I am now, next week I will try to hoist the jib. My sailboat will then finally be 'under sail'.

374.thumb.JPG.8d1c014d5c40f9ba203036cfb87695a4.JPG

 

Thank you to follow

Thank you for the likes

Thank you for your constructive comments

 

Till next week

Share this post


Link to post
Share on other sites

Beautiful job on the sail G.L.

On 2/1/2020 at 2:52 AM, G.L. said:

Sewing the jib leach is very time consuming, it took most of the time this week

Looks like time well spent - it turned out great.

 

I like your method of producing the thimbles. Very authentic looking.

 

Gary

Share this post


Link to post
Share on other sites
On 2/1/2020 at 8:32 PM, michael mott said:

A very nice looking sail Geert.

 

Michael

 

On 2/1/2020 at 8:42 PM, Jim Lad said:

A beautifully constructed sail, Geert.

 

John

 

On 2/3/2020 at 12:03 AM, FriedClams said:

Beautiful job on the sail G.L.

Looks like time well spent - it turned out great.

 

I like your method of producing the thimbles. Very authentic looking.

 

Gary

 

On 2/3/2020 at 1:23 AM, druxey said:

Very neat needlework, Geert!

Thank you very much for your comments, my friends.

In fact every thing that I apply in making the sails, I learned it from you by reading all your logs on this forum and also from my wife who accompanies me in the working with the sewing machine.

Share this post


Link to post
Share on other sites

The jib will be attached to the fore stay by jib hanks. To make the hanks, I make a simple jig with one 3mm nail and two 1mm nails.

375.thumb.JPG.5673c88765f13a3e309575140feaf87e.JPG

Making the hanks is just turning a copper wire around the nails and cut it at both ends.

376.thumb.JPG.5475e4c01a12db9b5961cf147500ddf8.JPG

 

377.thumb.JPG.4a0a9bff5c163b0c94c74aedb87b04ad.JPG

In no time I have more than enough jib hanks and I can start to sew them on the sail. They are sewn first at one side of the sail ...

378.thumb.JPG.e143a3b862bae9ee6c3fb944e4782136.JPG

 

379.thumb.JPG.68d0c2ced2165e669cae405bf08b0a4c.JPG

... then, at the other side (that takes a bit more time).

380.thumb.JPG.2db38e813029967644d10258320058c5.JPG

Here the sail is completely done and ready to be rigged and hoisted.

381.thumb.JPG.75a49081a2b67cc919b3db6c77c35282.JPG

At least my boat is under sail. Next week I can start with the main sail.

382.thumb.JPG.4074b0d4fc23320484f476398e9b348f.JPG

 

383.thumb.JPG.65b335ac31f9bc4f58eb25a45de9ebd7.JPG

 

DSC01458.thumb.JPG.f221e1ce0410a20e4a61e9c44a6775a3.JPG

Share this post


Link to post
Share on other sites

Making the mail sail starts just like the jib with drawing the shape on the canvas (in this case poplin coton). I add 4mm at each side to make a border hem.

384.thumb.JPG.b8d0af9897ea64d1b5081add8aeca244.JPG

Before cutting, I brush some textile glue over the borders to prevent them of fraying out.

385.thumb.JPG.3d090b0d3868450d0cf596a7b2cc275a.JPG

The sail is cut with a border of 4mm at each side.

386.thumb.JPG.4098fcb2aa3cbb4ab2801dab1ce8a1b9.JPG

I start to stitch parallel lines to show the different lanes of the sail. I use the small sewing machine on which my wife learned machine sewing some thirty years ago. Now she has another machine which is much to complicate for me to use.

387.thumb.JPG.1394f195a90ae8a7695dc0c2f5c8fa92.JPG

 

388.thumb.JPG.9022cce66e3c8cc609ea397b387c6caa.JPG

 

389.thumb.JPG.deab8069cef6cd06ec5be9a95731aff8.JPG

After the lanes are stitched, I pin the edges of the sail.

390.thumb.JPG.04ccab1f06c6d7b209e6589667e5ec75.JPG

Then they can be stitched as well.

391.thumb.JPG.3d114cfd15d39a5ed3f856ea29ed9790.JPG

The main sail is stitched.

392.thumb.JPG.a9a9d9184d10339054b953f3bf15d202.JPG

I sew now the reefing cringles with a thimble in them. The main sail has two reefing levels.

393.thumb.JPG.b2f58f61d2ba0702e4052406633f412d.JPG

The four cringles are done, now it is time to sew the leach around the whole sail.

394.thumb.JPG.40f7b77443cfb40814fa8a83e62f71ef.JPG

 

Thank you for the likes

Thank you to follow

 

Till next week!

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Recently Browsing   0 members

    No registered users viewing this page.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem

Modelshipworld - Advancing Ship Modeling through Research
×
×
  • Create New...