Jump to content

HM Brig-Sloop Speedy by glennard2523 - Vanguard Models - 1/64


Recommended Posts

I'm loving it!    I'm still slogging through the first planking.  It looks beautiful so far.

 

I'm playing with the idea of backdating mine to the age of crows feet, because I see many a 28, 36, and 44 in my future....

 

Carry on, Sir!!   It's looking bloody marvelous.  Sir Glenmorangie says so hisself, he does.

On the bench:  Vanguard Models 1/64 HMS Speedy

 

On Deck:

Vanguard Models 1/64 Zulu,

Vanguard Models 1/64 Fifie,

Victory Models 1/72 HMS Bellerophon 

Link to comment
Share on other sites

Looking really good Glenn. I’m sure you’re right to fit the gaff and boom first. 
 

Derek

Cheers, Derek

 

Current build:   Duchess of Kingston

On hold:              HMS Winchelsea

 

Previous builds:  HMS SpeedyEnglish Pinnace, Royal Yacht Caroline (gallery),

                            Victory Cross-section (gallery), US Clipper Albatros, Red Dragon (years ago!)

 

On the stocks:    18th Century Longboat

Link to comment
Share on other sites

  • 2 weeks later...

My progress is slow at the moment. I have finally installed both the rudder and the main mast so today I started work on adding the boom prior to fitting the shrouds.

 

As can be seen from the plan sheet there is a nice double block assembly required for the boom topping lift.

33222235_225BoomToppingLiftRigging.thumb.jpg.027ebdfa55d3d7da529e0cd1cd7be292.jpg

This took a little bit of time and effort to get the loops on the blocks, but it was not as difficult as I first feared and the boom was fitted and the topping lift added without to many problems. I just need to finish off belaying the drop. I have positioned it around the belaying pin, but I needed to take a break so will come back to it tomorrow to finish it off and add the other boom rigging. I will also add and rig the gaff in the next few days before I start work on the main mast shrouds.

1647542771_226BoomToppingLift.thumb.jpg.b9c3f858bbd26f0359c10c748d26dbb1.jpg

65609171_227BoomFittedBelyaingstillrequired.thumb.jpg.4501fef289d98950e9c2a4d4ddc1f49d.jpg

I realised that I had not fitted the cleats to the stern patterns so it was a bit tricky drilling the holes with the tiller and cannons in situ, but I took my time and managed it without incident.

 

 

Glenn (UK)

Link to comment
Share on other sites

Looking really good!

Cheers, Derek

 

Current build:   Duchess of Kingston

On hold:              HMS Winchelsea

 

Previous builds:  HMS SpeedyEnglish Pinnace, Royal Yacht Caroline (gallery),

                            Victory Cross-section (gallery), US Clipper Albatros, Red Dragon (years ago!)

 

On the stocks:    18th Century Longboat

Link to comment
Share on other sites

I have now finished adding the boom and gaff. I did have to redo the boom because I made a fundamental rigging error with the boom topping lift rigging, as I took it through the wrong double block on the main mast.

 

I did find it difficult threading the 0.25mm natural thread through the 3mm single blocks even when the end was hardened with ca, but eventually found a workable solution.

 

As I have said before I'm not very good at rigging, or taking photo's but I'm getting a bit better at the rigging.

 

1022802333_228BoomandGaff.thumb.jpg.c8e3e873edf7be2c59f9cccfb867a631.jpg775335182_229Boom.thumb.jpg.4ac8b7cc2e62e6bb820e5d2a383a3a05.jpg1220106805_230Boom.thumb.jpg.dd90c9ff5287e53750efcae490591dfb.jpg70634753_231Boom.thumb.jpg.40fc12079651f132c88389484632c734.jpg1631024155_232Gaff.thumb.jpg.9f0b080e1d96fb2ebb916eb8038d4014.jpg

Glenn (UK)

Link to comment
Share on other sites

Quote

I did find it difficult threading the 0.25mm natural thread through the 3mm single blocks even when the end was hardened with ca, but eventually found a workable solution.

What was your solution ? I hope to build the "Flirt" as my next project.

 

Richard

Richard

Current build :  Victory cross section / DeAgostini, Lady Eleanor  Vanguard Models 

Other builds :   N scale computer controlled model railroad

 

Link to comment
Share on other sites

Just now, Suzdal said:

What was your solution ? I hope to build the "Flirt" as my next project.

 

Richard

I taper the edge of the thread but cutting at approx. 45 degrees across the thread which really helps. I normally run a 0.6mm micro drill through the 3mm block holes which seems OK for the most part but I have increased the micro drill bit size to 0.7mm when the thread is 0.25mm which seems to have done the trick.

Glenn (UK)

Link to comment
Share on other sites

  • 4 weeks later...

I have not done an update for a while. I have decided to take a different approach and I plan to only part rig the build. The rigging instructions are very easy to follow but with my poor near vision, and my extra large hands I'm been finding it a challenge.

 

Also I have a new project starting shortly with a 1 / 250 scale build of the Yamato.

20200705_183135.thumb.jpg.2d319d107b49d039a04821db2a8e53cd.jpg20200705_183212.thumb.jpg.81b883657ac656c2e3fbe13d10eb4f8b.jpg20200705_183308.thumb.jpg.30ce0fa233427cdd7e23b363f0ab3ea9.jpg20200705_183409.thumb.jpg.8b0b0f64c1fe1b55f59523a15d956472.jpg

Glenn (UK)

Link to comment
Share on other sites

  • 1 month later...
  • 2 months later...
  • The title was changed to HM Brig-Sloop Speedy by glennard2523 - Vanguard Models - 1/64

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...