Jump to content

Nordlandsbaaden by Paul Le Wol - FINISHED - Billing Boats - 1/20


Recommended Posts

Hi Everyone, I have started my next project. About a year ago when I saw Ekis’ beautiful completed model I decided that I would like to give it a try. 
 

FAF49A2B-23E1-4BE3-BDA0-5C620097B22C.thumb.jpeg.2297ad0468be2007d529175f90a585ec.jpeg

 

The build board was started  about a month ago. Picked up a 12”x 36” pine project panel at Home Depot. It was surprisingly flat and straight. The aluminum T-channel, T-bolts, and knobs are from Lee Valley, the sticky-backed measuring tape is made by Starret and is from Amazon and the 2” aluminum square tube is from Aircraft Spruce. The first thing the directions tell you to do is remove the frames and bulkheads from the carrier sheet and mount them on the build board, then plank the boat. If Billings ever published a recipe book, all of the recipes would say-

 

Step 1: Put in pot

 

Step 2: Boil

 

Step 3: Eat


Because the two center channels are proud of the board the frames have to be notched. The notch also keeps the frame centered.

 

A943E4B8-30CD-47E9-8D23-F7F055580C58.thumb.jpeg.8fe36f85ceb62e91de57c49f1c69ae0c.jpeg

 

4C9C98B3-4EF8-4FB3-BB2B-78002A4E8BD4.thumb.jpeg.31a43ca4f1d9b2b99e8be8f6a5f9a1ef.jpeg

 

3541FDA5-57E9-46E9-8DD6-7AF6791F730A.thumb.jpeg.3d90e7f5fa420e20bffe80f03f9bbcc4.jpeg

 

I didn’t need the piece above the notches so it was not removed. Blocks of wood were glued to the various frames to help with the assembly.

 

926305F5-9253-43AC-8AB5-932E31E39C66.thumb.jpeg.f6d8763ef51ff27ee7ecdd4b779286c7.jpeg

80B3FE6C-3DA6-42E1-9588-8921BDB3D82F.thumb.jpeg.f54ffc14e47b1f0c9938fc8aa0ebc9bf.jpeg

 

 

The frames were then screwed to the crosspieces.
 

C2A8C320-1D0A-49DD-8D02-6F3CA301292A.thumb.jpeg.25260b8e42958d9ea4051a3f49ff5b68.jpeg

 

 

E3EF62DA-D8B6-49E6-8022-59476AEC576A.thumb.jpeg.7f7d3d2b7386c6d16c5f7e53e72b63e8.jpeg
 

FC31A899-3CB1-43A1-B3E2-F7A4BF640D68.thumb.jpeg.3ba13b8b8083cb514ae45dadae3fccc8.jpeg

 

663AF11B-1B95-47F9-B9F7-74E61CDE3ABA.thumb.jpeg.4553196ed36815f5fc05e4f1e4935d02.jpeg

 

57D27C86-B145-43CF-BAF4-A51F8ACEAF9D.thumb.jpeg.98910a425698accb1354d14b939fb92d.jpeg

 

8DE7E5A3-DB43-438D-B28C-CCBA966E5F6C.thumb.jpeg.7f5de0bb62cd3f728bbff281ab6841ff.jpeg

 

3E80EED1-D225-41F6-8AE8-28EDADA6249E.thumb.jpeg.14ec6d5582e3e75e5c5f43dab2e18a28.jpeg

 

Used some pieces from Cheerful’s carrier sheet to support the front of the cabin.

 

0172C8EA-3ECE-4432-8F65-2691C9065352.thumb.jpeg.663cba3073f19cd9d56c49cb1d06438b.jpeg

 

0066BD03-525C-4EAC-9883-3EFCA6FAEEAA.thumb.jpeg.9f058bebf4ab9e1bb53d1abd57cc0d14.jpeg

 

Glued in the kit supplied strips that support the frames.

 

 

242E9B50-A8EE-4192-8DC1-8CEB29C58F18.thumb.jpeg.77f51df7d30ac8e525aa1171d7774ba0.jpeg

 

There are two triangular shaped pieces that are glued in at the stern. The side that is glued to the keel/ frame has to be sanded at an angle. Clamped a small piece of wood to the stern post to support these pieces while gluing. It’s difficult to tell if you’ve sanded enough when everything is upside down.
 

B16AB5F6-6354-4AEF-905D-7A36F0243417.thumb.jpeg.068b6b167e574d0bd83a5138e230da98.jpeg

 

AE85B768-30B1-428E-BB5C-E4DEEA933F4A.thumb.jpeg.88829f3bc55b8a030642c3d8c04ac864.jpeg

 

98A6F922-0593-46EA-B1FE-296E7EB06B8A.thumb.jpeg.2c1eced1a9964b5393c718bf7e297283.jpeg

 

The two frames toward the bow are just for support and nothing is glued to them. To keep them from moving around, the keel was tie wired to them. I transferred a line from the plans to the keel that indicates the bottom of the garboard. As you can see there needs to be some adjustments made to something.

 

EAED8FE4-1B58-417B-8A90-704ABEA8FFC4.thumb.jpeg.c736bb1dc1caa8e1ecd8f99a277010c3.jpeg

 

96F36868-18A5-4150-B86A-65EF29791E49.thumb.jpeg.73bd7e0cbc96a8f22b88820d344c6d3c.jpeg

 

Just need to find one more 1/4-20 nut for the stem clamp. Now it’s ready to plank. Hope to see you all soon.

 

 

 

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

Thanks Todd, the board isn’t really any different than other boards you see on this forum. I like the fact that you can make adjustments when needed to the spacing of the cross pieces. These t-bolts slide  inside the track and the knobs have a captured nut inside them. You make the crosspieces out of whatever type and size of material that suits your needs. I guess if you needed more crosspieces closer together you would have to just use a bare nut to secure them. The two center channels were placed 3/16” apart so that the keel can fit in there when the boat gets flipped over. Then you can make brackets to hold the stem and the stern. Everything was screwed to the board using #4x 3/4 “ flat head screws. Countersunk holes were drilled in the channels so that the t-bolt would not contact the head of the screw.B187C588-5CD0-424C-B99C-673FBF765AF2.thumb.jpeg.e52739c9404d9a31016211b4fdf76947.jpeg

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

  • 2 weeks later...

Hey Everyone, thank you for your comments and Likes. Well this Nordland Boat has been kicking my butt for the past week. Started off by trimming and sanding back the frames where they meet the keel.

 

A0B53083-E00A-4F2D-A6AF-5118D46E394C.thumb.jpeg.6470a11e805506b0beff2e9a3fbe457b.jpeg

 

They now match the line that I transferred to the keel from the drawings. The planks are laser cut 3/64” 3-ply plywood. They are tough as nails. 
 

922D2E0F-162B-48EF-AF19-CD0AEFF012CA.thumb.jpeg.61cca4c186195db9aa5dcc7151595f2e.jpeg

 

The garboard plank was glued to the keel using the line as a reference for the bottom of the plank.

 

62DAA152-320D-4415-B27C-0EDEAC70B79F.thumb.jpeg.3a0204174f4e0b4295278b66b85ea576.jpeg

 

I’m completing both sides before moving to the next plank. There are lines lasered into the frames/bulkheads  to show you where the planks should end up. There are also tiny holes lasered into the keel that show where the planks start and end.

 

A195D673-5B41-4A19-BB67-363708180833.thumb.jpeg.b5b228e5e292c1bed4ddd09d17c0eeb0.jpeg

 

00CBE0D3-E88B-49EF-B45A-494C0BF20101.thumb.jpeg.7b014273b4a309ef54f64cf9a776672a.jpeg

 

You can see that the second plank did not manage to get to the mark. It was a struggle to meet the line until the fourth plank.

 

14E2AE31-BCDF-4D5D-8623-43A6EBFF7D37.thumb.jpeg.558a22a02273dca04585ac22afccf682.jpeg

 

96FF4F7C-58BD-402F-A5BF-175153A61AD2.thumb.jpeg.6d111f51bd48cdce851b5a84adf611c0.jpeg

 

BAD4BD10-DBC6-4324-AC58-8E4F3EFD4997.thumb.jpeg.4611787920f41544036fbf72e0350929.jpeg

 

D198CA78-257C-4933-94AB-E58E1798E2F4.thumb.jpeg.02ff9b2ce02f2247a66dede3c51aaa59.jpeg

 

After test fitting the seventh plank I decided to remove the boat from to build board because it didn’t look like it was going well.

 

7B9E442B-A81C-4505-8F21-AFE68C923FB1.thumb.jpeg.a5d38186a2c9fe598e2710435b2c5ead.jpeg

 

DDA810CF-C681-4E02-A35E-1C94EEE49D10.thumb.jpeg.d0e0f4e248e1bdb90648e464d9c4cf0b.jpeg

 

She had a bit of a twist to her so back in the build board it went. Laid a bunch of glue along each side of the keel to give it some strength.

 

E6820A24-897E-4C06-917C-5841CFCA8334.thumb.jpeg.e5147b7eb5ba562d113c6b8f20c76d2b.jpeg

 

6FEAB176-A385-49AE-9A46-AAAAC9C50008.thumb.jpeg.ea6d16532bb25bd2ff5621373d54a550.jpeg

 

Wanted to see how the frames would fit in the hull at this point so I started assembling frames.

 Put scabs on each side to give them some strength.

 

469A8779-838A-45FD-B6CC-670129ED0D2D.thumb.jpeg.4f9dfa7391766b88628dfeb6c3c61479.jpeg

 

A365AB39-086B-40C1-9CA0-700137F05A7C.thumb.jpeg.105e7d413d525466fa50f373e5a70d48.jpeg

 

ED7CF475-E35A-447D-A9FC-01DF3EA9AC29.thumb.jpeg.37d304728cadb21a49a7171258187004.jpeg

 

There are lines etched in the keel that I think are to show where the frames are placed but they don’t match the plans. Going to use them for frame placement.

 

5BB2C9F8-0675-467E-AB22-FF3A6EB564CD.thumb.jpeg.6f6368fdcbf6bdb32fde7f8f2138a40d.jpeg

 

Temporarily glued four frames to the hull and they fit fairly well with a bit of tweaking.

 

1248F716-5826-4AA3-95E3-698E46902309.thumb.jpeg.13a2c09dd3cf11fe36417f693e7bf005.jpeg

 

5F9643B2-9ADA-474C-B3A6-F0169B006461.thumb.jpeg.513e9e0a1a328e2d41639b62dadd145e.jpeg

 

Figured that was a good test fitting. Removed all of the frames except the one at the mast. There are laser cut plywood pieces that are glued to the keel under the frames and then the frames are glued to them. I am assuming all of this because it doesn’t tell you anywhere that this is what you do. They all need to be cut and shaped to fit. Using the build board to hold them down while gluing.


 

D46101D1-FA1A-4F56-A626-5F4A434E99EF.thumb.jpeg.7140aa540d21b18554207d76dc7ea6e3.jpeg

 

062FFFBE-E39F-4B06-A571-2ADF8403E126.thumb.jpeg.3989c1923260e9962e5b385896dad942.jpeg
 

 

The plan is to finish the plywood under the frames and then to permanently install the frames. Flip it back over and finish the planking. Thought it would be easier to plank if the frames were there to glue to. Might not be a good plan but we shall see.

 

 

C8908A7F-0D24-4AF9-B245-DED70782F809.jpeg

Edited by Paul Le Wol

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

I am totally impressed with how you have everything squared up with that building board. It's going to be a lovely model.

 

Ian

Link to comment
Share on other sites

Hi Everyone, thank you for your comments and Likes. The plywood floor and the frames have been completed. Just a few photos to show the process. All of the frames had to be trimmed, filed and/or sanded to match the planking. So lots and lots of test fitting.

 

A9060BED-E306-4065-BC27-CD4E4C7C71CF.thumb.jpeg.80c43112eabdbb7a8897522b8d97f6b0.jpeg


 

E9061C1D-FE70-44C4-980C-36A06D1120B7.thumb.jpeg.7ef3fd0c86d340d36d8311ef366ff1b4.jpeg

 

 

B22F4AF4-A805-452E-A5D6-39FD297C31F1.thumb.jpeg.cd10ca4ce53e97b28a1b93b2394ac4e5.jpeg

 

 

F0D4F095-A336-4103-8ABF-DE7794EA8CD3.thumb.jpeg.2e44ebe7de2b296f5eb80d8c3061c836.jpeg

 

 

 

C5091902-F73F-4F96-A235-D73BFBFD22D2.thumb.jpeg.844375179f0c3a04a2d1ee9155a87f31.jpeg
 

 

0D5FCBDC-CC8F-4392-B1B3-E3A5634FE2BF.thumb.jpeg.4da9a341b0cf00f1b84ca5a3387ef762.jpeg

 

 

2EFB6115-1CB3-41B2-B91D-81D4621F2066.thumb.jpeg.06c4a78b7bcb8e4da4eca235877c5dad.jpeg

 

 

EBA6526A-CBE3-4137-B907-4B02CC8343F2.thumb.jpeg.34a15cf7c88e193e51671c98fe23993d.jpeg

 

Time to turn it over and resume planking.

 

Edited by Paul Le Wol

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

Hi Cisco, these laser cut planks are a bit of a mixed blessing. Sometimes they can be a little ornery that’s for sure.

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

  • 2 weeks later...

Hello Everyone, I hope you are all enjoying the weekend. Thank you very much for the likes and comments. This week the boat was turned over and planking was resumed. This is a very clamp intensive model.  Only been doing one plank a day because of a lack of clamps. Picked up some 2 inch clamps at Princess Auto. Should have bought everyone they had.
 

71073A30-23D7-4582-B6AA-F18BB2A06EBD.thumb.jpeg.6710c977847da6475ebbf5262559d22e.jpeg

 

B87BAD78-0CF6-4DA6-82CB-79CDAF0894F6.thumb.jpeg.8d6172351b072cc2cc8b88e710ce44a9.jpeg

 

_EB2EA0EA-41EC-4A6A-A2CD-F325467FE7EC.thumb.jpeg.07b52d818c00f036eca77ea1ff8e8a6e.jpeg


Added some bracing between the stern post  and the bulkhead to keep the planks from cutting across that large space.

 

51E266E5-5A53-419F-AB1B-ED5946617D0F.thumb.jpeg.1b4b81e741c96e4d4195787b7d1f111e.jpeg

 

All of the planks except the last ones have gains cut in them at the stern post and the stem. It also helps to keep them positioned correctly when gluing.

 

 

F2B1D725-5446-44F2-A8B8-8D8F233C0CDB.thumb.jpeg.dd697d49268fb14c3412771b55a8326b.jpeg


 

All of the planks had to be trimmed a bit so there’s a lot of clamping, test fitting, removing, cutting, clamping…………

 

C84BC75C-4E44-411D-ABE2-1FFAB949036D.thumb.jpeg.24427a072e5692e341a34fb9a9d9d44d.jpeg

 

184B9ADD-4589-460F-AC7C-643C08FB5821.thumb.jpeg.0eac3a59c798922aac3ad8f4a39535fe.jpeg

 

 

093C9355-B250-407E-A510-A5CC28B67012.thumb.jpeg.c00a35cc916c9721d2e2d5c19ace0571.jpeg

 

And now there are 9 planks on each side. Turned it over and started cleaning up the interior of the hull. Actually it wasn’t all that bad inside. I thought there would be more glue everywhere.

 

0FE9A6D6-9092-4D2E-82B7-411AF9D3C88E.thumb.jpeg.c0d6e27b2ab5fd3a63f3537699a8cef6.jpeg

 

01F64819-D14F-47D8-9878-63CAA31B3F93.thumb.jpeg.e4f75874a9fbaa8685536251d82079fa.jpeg

 

I think the next thing on the agenda is to cover each side of the stem, keel and stern post with 1/32” basswood. Doesn’t really need it but I think it will look better. Also trying to decide what colors to paint her.

 

Sorry, this photo is out of place.

 

EF7DC3CB-6938-478A-94E7-044AE94A4991.jpeg

Edited by Paul Le Wol

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

Nice work Paul

Regards, Patrick

 

Finished :  Soleil Royal Heller 1/100   Wasa Billing Boats   Bounty Revell 1/110 plastic (semi scratch)   Pelican / Golden Hind  1/45 scratch

Current build :  Mary Rose 1/50 scratch

Gallery Revell Bounty  Pelican/Golden hind 1/45 scratch

To do Prins Willem Corel, Le Tonnant Corel, Yacht d'Oro Corel, Thermopylae Sergal 

 

Shore leave,  non ship models build logs :  

ADGZ M35 funkwagen 1/72    Einhets Pkw. Kfz.2 and 4 1/72   Autoblinda AB40 1/72   122mm A-19 & 152mm ML-20 & 12.8cm Pak.44 {K8 1/2} 1/72   10.5cm Howitzer 16 on Mark. VI(e)  Centurion Mk.1 conversion   M29 Weasel 1/72     SAM6 1/72    T26 Finland  T26 TN 1/72  Autoprotetto S37 1/72     Opel Blitz buses 1/72  Boxer and MAN trucks 1/72   Hetzer38(t) Starr 1/72    

 

Si vis pacem, para bellum

 
 
Link to comment
Share on other sites

Hi Everyone, my thanks to all of you for the Likes. Patrick and Ian, thank you so much for the comments. A big storm blew through here yesterday and the power was down for 12 hours so I’m making up for lost time. Had a bit of 1/32” basswood so I started on veneering the stern post.

 

BD4E955B-25DA-4F91-B775-A2842E9F1920.thumb.jpeg.d2f4cb53596d13ce734b0cd82a60b99d.jpeg

 

A1A8213F-15DF-46CB-ACF4-2D63AC72724E.thumb.jpeg.173cddfa4f81fae77d1a030998bdaad4.jpeg

 

Have to get over to the hobby store this week to get some more.

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

  • 2 weeks later...

Hi Everyone, thank you for your Likes and Comments. They are always very nice to receive. The veneering of the stem, keel and stern post is finished.

 

885786A9-59B6-4A90-8087-F20E27490B1E.thumb.jpeg.7591fdc9362a2a6e336489c1f9503de1.jpeg


 

849ED58F-F10A-44DF-9E1E-B394BCD1D562.thumb.jpeg.994d1d00f526a4e0b7b0f96a57855314.jpeg


 

07F1594B-4890-46FE-8E08-774870B6838F.thumb.jpeg.fb22898685339156b98424087024c77c.jpeg


 

03574B3D-33EF-41B9-9C9F-402026EEEDA2.thumb.jpeg.f3377f713a22e97169869f5c2a20793e.jpeg

 

 

I also spent a bit of time this week testing stain and paint colors. 
 

428A9BE5-ED0D-4DFA-8E22-DC082B333085.thumb.jpeg.caf3d94b933e4d0da0e6efacfad11978.jpeg


 

349EF804-3C54-45C0-A553-953D110AAFA5.thumb.jpeg.7aaa3d35c6304438d727555897fa84d2.jpeg

 

The Varithane Espresso turned out to be more black looking than brown so it may be used for the cabin roof. The Minwax Red Mahogany was tested where it will be covered by the deck. The gel stain didn’t cover all that well and it washed off a bit when applying the wipe on poly over it. I also ran a pencil along the tops of the planks to simulate caulking but didn’t really like that. But when the w-o-p was applied over it the graphite, or whatever they make pencils out of these days, it smeared around giving the planks a weathered kind of mildewed look. Between the next two ribs I grated some HB lead from a mechanical pencil and smooshed it around with w-o-p on a cotton swab.

 

FB6D9CA5-985D-421C-BEC2-64509390B142.thumb.jpeg.9d821578cf743c40ef9b23634755e151.jpeg

 

809CC944-EBBE-42D7-B548-8C7803C9C7C1.thumb.jpeg.415ed5f52379224da26a1be303f2ca8a.jpeg

 

That turned out pretty good. Kit supplied Obechi is being used for the floor boards to cover the plywood. The instructions say to score and draw lines on the plywood to simulate planks. The Obechi didn’t like the graphite. It has a deep grain in it. Started making thwarts out of pear to replace the plywood kit-supplied parts.

 

D9EF19FE-A85B-4A5E-A01B-779E3086FCB7.thumb.jpeg.f93f33385f558cdab4703a073c3a655c.jpeg


 

107C717B-782E-454E-9E77-CA478B3DE1BD.thumb.jpeg.5188c9aa126ba501549b9971d47e03ca.jpeg

 

3B00438C-DDF1-4FC4-A87F-0F87859A8E9A.thumb.jpeg.17a0029089f05683f54f1ac9753ce0ed.jpeg


 

8A4A443D-22AC-4B17-866D-572924E37EEC.thumb.jpeg.8ca57ade7d9e2545c0c83d11e105b945.jpeg


 

The third test area turned out too dark and blotchy because a second coat was applied before the first one dried. From that point on, the graphite was mixed in a bottle cap with the w-o-p and then applied. The deck boards were made using what I believe is pear also. 
 

 

7D04AE7B-FA17-497F-BB79-433BEFDA6499.thumb.jpeg.a4bd09beb79a17855450d08f5c540716.jpeg


 

063D34EA-749B-4DDC-A591-0FD1CCC7BAB3.thumb.jpeg.a32b416848eea2a3c0188b3e491b6c96.jpeg


 

ADF3C660-E556-4DD5-A702-43F3F281DA54.thumb.jpeg.4197d3d96703a58f9346443eff6e21c3.jpeg

 

The floor boards were then finished 

 

1ED9ABA5-23A3-4AC7-BDE8-415146C814DD.thumb.jpeg.6dfabac17255fceec0b1c7e43363b909.jpeg

 

 

 

1F195CBD-FD3D-432C-9B3E-5AE46DE2218A.thumb.jpeg.b9238a158f7942707aeb8f4180bf842e.jpeg
 


8516082B-A6CB-4647-9AED-5E7E890480BD.thumb.jpeg.9b3c547c376d493b480e1b4127071095.jpeg

 

Next will be making more thwarts and then some work on the gunwales. See you next time.

 

Edited by Paul Le Wol

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

Hi Everyone, thanks for dropping by and many thanks for the Likes. I was going to work on the gunwale rails (Billings calls them rails ) but it seemed to me to be better to attach the side walls of the cabin first. These are the kit supplied rails that taper to an end about half way between the front of the cabin and the stern post.

 

5D69716A-78FA-4610-8355-5B9D1BEBA021.thumb.jpeg.2c23dbf82215dedbb275842e67a03a2e.jpeg

 

If you install them first then the cabin wall would have to drop down to the gunwale strake (?) where they end. Thought there would be too much room for error there. I have some AYC left over from my Cheerful build so the plywood cabin walls will be replaced with it. I also broke one of the plywood parts. They are very tender where the porthole is cut in. 

 


620771FE-D6F7-49AA-8328-57AFD0CD0442.thumb.jpeg.596a4ac483717e2dc8f25d487ad10c9d.jpeg

 

The cabin walls curve then twist and then straighten out. At the halfway mark they stop following the planking and head inboard where they attach to the front of the cabin. Some 1/8” basswood parts where made to keep the walls on track.

 

BCD6FE97-1764-426E-A857-7B87E1C8AF3C.thumb.jpeg.390a40882e50a72661fd05183a50ce30.jpeg

 


D57468B9-2919-437E-A6CC-ECD6A8C13888.thumb.jpeg.886aa878d8ebcc595f3ff812073ee395.jpeg

 

CA was used from the stern post to the first bulkhead and then pva and clamps took over.

 

EC25A6ED-F00B-4174-A94D-8D7672D1DD76.thumb.jpeg.3e92babef391ab4d308899426cad51fc.jpeg

 

174938B8-09B2-48DB-818D-D7E73E4C2DEC.thumb.jpeg.82d433f679264631d323a7449ac7c397.jpeg

 

This is her after a first sanding and application of w-o-p. The red oxide is starting to grow on me.

 

EB22AD43-98E6-4AF2-971A-D1CA95846F67.thumb.jpeg.0cf4a767c080d19da9ffc9c6d38b427f.jpeg

 

1311AC90-5168-46D1-B33D-B4973E47D911.thumb.jpeg.9037e3b4d29cc69c4c4fce2e398f84e3.jpeg

 

The thwarts have also been finished.

 

BC5B0A84-6356-4638-A1D3-25487B7DE223.thumb.jpeg.635134e0fe19b48bc978467efd9257d6.jpeg

 

I’ve been adding 1/16” x 1/16” strips of basswood along the top plank to give more gluing surface for the rail. Once they are completed the rails can be worked on.

 

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

  • 2 weeks later...

Hello Everyone, there is a bit more progress to show. Thanks to all of you for your comments and Likes. A template of the fore most frame was made so as to figure out where the rails would end.

 

37237A81-F6A7-4DD3-89A8-CC7A24671354.thumb.jpeg.91818643e9b0150fa527a488ff3ec248.jpeg

 

 

The kit supplied rails where marked, cut and test fitted to the hull. Once they where close they where used as templates to make new rails out of 3/32” AYS. 
 

89A735DB-E048-4BAB-8564-94A958706231.thumb.jpeg.c5148aeca02adae44aa30ce31a39b983.jpeg

 

91571DE2-ECAA-41FB-B8BA-A4D1A4C70C1F.thumb.jpeg.923d3fcd6e38367736f3bbd5306daaa9.jpeg

 

The port and starboard rails from the stern to midship were glued with pva and clamped. They were made extra wide because I thought it would be easier to trim them later than try to make them more accurately. 
 

B2FE2EC3-5C95-4491-A59E-A4B5F5A2F316.thumb.jpeg.39d9d4fc6971206e80d935d68e51f756.jpeg

 

F3D03FAC-2D71-4521-A9AE-5E36E6D081AB.thumb.jpeg.84be97791c9e6ae4cd6b2b83276a9324.jpeg

 

1947F595-D4F5-449B-9011-407615B4B11B.thumb.jpeg.ae0072218e3f189b78e029b94d83be4f.jpeg

 

The remainder of the rails up to the last frame before the stem were moistened, heated, clamped to the spaghetti pot and left overnight.

 

0F85042A-8CF8-4F63-9744-4F8B6DD6D673.thumb.jpeg.527783b97009c7f85364f205a0c53d3b.jpeg

 

6933AAE5-6FD8-4E44-9E66-72AE440631AC.thumb.jpeg.d1161bf29cbd41ce76ccaf386d0ddc0d.jpeg

 

BB0BB071-24A9-4B0D-9403-89F6A4645592.thumb.jpeg.ab4e0c9efb8091fb04c5c28c7b5da7c8.jpeg

 

There is a piece of trim that runs under the rail from stem to stern. I used a piece of 1/16”x 1/8” AYS. It had to be shaped at the stern and edge bent at the stem. CA was used at each end and pva was used in between.

 

4B632BC5-EE51-47B0-85B4-3429AB96EAE6.thumb.jpeg.7dc1f3f6569fab8ddfbb9f1d616262de.jpeg

 

7CA0FE78-01A8-427A-A189-B086348ADB43.thumb.jpeg.c2c499303a441ee1e551262f58eeb101.jpeg

 

While all this was going on and glue was drying I started on the doors and trim for the front of the cabin.

 

DB71C410-AA3B-4066-9E78-33BC16C616FC.thumb.jpeg.777d14d95346efe1973b17f5a4d4dc4c.jpeg

 

4ADF30CF-8E43-4980-872E-1598F9BF1469.thumb.jpeg.6251dee9bd5ef745599b5613e528b39a.jpeg

 

5E759322-98C3-43DF-B257-3257E41A202D.thumb.jpeg.46a59a2e3dbe4eb5520254e7dda11a12.jpeg

 

 I had some 1/4” x#18 brass escutcheon pins laying around so they became the doorknobs. Now there’s just a whole bunch of planing and sanding to get the rails to the proper width. After that there is another piece of wood that runs along the top of the rail on its inboard edge

 

C37ABAF3-D67A-42B7-87E1-7B55B2D9D550.thumb.jpeg.5750abbb3234d782c84a14ce39250541.jpeg

 

F69BA95A-D322-40F6-91F4-06C7FFDF5439.thumb.jpeg.00fd951ad1d7ec0b53b59a28bdcd1c1f.jpeg

 

35BE2D6B-7B1F-4497-9D2A-DDB2D23A77D9.thumb.jpeg.611a072c968c498c025117a3ee5b2ad4.jpeg

 

 

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

Hi Cisco, thank you very much. Billings has this kit listed in their “ Experienced “ category but I think that if someone took their time with getting the planking right it would be a good project for anyone. I have a couple of wonky spots in the hull but overall it came out fairly straight. At 1/20 scale you sure don’t have to worry about tiny parts.

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

Hi Paul,

congrats, thats a beautiful build, accurate and precise....

 

Nils

Current builds

-Lightship Elbe 1

Completed

- Steamship Ergenstrasse ex Laker Corsicana 1918- scale 1:87 scratchbuild

"Zeesboot"  heritage wooden fishing small craft around 1870, POB  clinker scratch build scale 1:24

Pilot Schooner # 5 ELBE  ex Wanderbird, scale 1:50 scratchbuild

Mississippi Sterwheelsteamer built as christmapresent for grandson modified kit build

Chebec "Eagle of Algier" 1753--scale 1:48-POB-(scratchbuild) 

"SS Kaiser Wilhelm der Grosse" four stacker passenger liner of 1897, blue ribbond awarded, 1:144 (scratchbuild)
"HMS Pegasus" , 16 gun sloop, Swan-Class 1776-1777 scale 1:64 from Amati plan 

-"Pamir" 4-mast barque, P-liner, 1:96  (scratchbuild)

-"Gorch Fock 2" German Navy cadet training 3-mast barque, 1:95 (scratchbuild) 

"Heinrich Kayser" heritage Merchant Steamship, 1:96 (scratchbuild)  original was my grandfathers ship

-"Bohuslän" , heritage ,live Swedish museum passenger steamer (Billings kit), 1:50 

"Lorbas", river tug, steam driven for RC, fictive design (scratchbuild), scale appr. 1:32

under restoration / restoration finished 

"Hjejlen" steam paddlewheeler, 1861, Billings Boats rare old kit, scale 1:50

Link to comment
Share on other sites

Hi Nils, thank you so much. This scale of boat is a lot easier to work on for me. But at 28” x 28” they do take up a lot of room.

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

Hey Everyone, thanks to all of you for your comments and Likes. This week was spent working on the rails. There is a plank that sits on its edge and runs along the outboard side of the rail. Half lap joints were used at both ends. The half lap scarf joint at the forward end should be tapered but this was just easier for mounting and gluing. The jig was made with scrap pieces of 3/64” plywood from the carrier sheet and the plank is 3/32” x 3/16”.

 

1C02E46A-9CDF-4B00-AB01-78E0D9DEB0F2.thumb.jpeg.4746dc3aeee1582a1985b1f2222d27b9.jpeg


 

07FFE95B-09FC-4730-8B32-6F127E812C88.thumb.jpeg.beb4d413a5afa5b55e6c9b2d192832a5.jpeg


 

CC2DDC79-9F0A-43D2-8122-55D669B0BA1C.thumb.jpeg.04fa9de716ec70442ea48101186225d8.jpeg

 


‘The four pieces of plank were glued on at the rate of one per day.

 

7CA6614E-15DD-4D81-8E02-4229886E801F.thumb.jpeg.244423f5d63200d92eece8c97715b057.jpeg


 

EC19D3FC-A021-467A-AA17-5F0975C68820.thumb.jpeg.8c5f585ee7f0adc38242b11831df3dea.jpeg


 


7ABDF073-B497-4536-B37B-1C0CF5286DB8.thumb.jpeg.11b00ec8086ee9f55e35cecb081b1fcb.jpeg

 

The forward port and starboard pieces required tapering and edge bending 

 

06FCDF25-8092-4CEC-8D65-4733B01B9BA7.thumb.jpeg.b5e096c2b30a0b31d3d0fbfc371ef43b.jpeg

 

The symmetry at the bow is a little off.

 

5CBD13DA-8B7D-4371-9E63-0FA09D9FB186.thumb.jpeg.4f4e782ac4751ac583f61ee3fdcfcf96.jpeg


 

A30F2A32-6FED-4569-8D34-9A9B3ACFD3C7.thumb.jpeg.12a073a52a1848d171a4dc8ecadf2158.jpeg
 

 

Three thwarts had to be removed so that the belaying pins could be attached to their undersides. I forgot to do that. If you use the Billings parts there are holes burned right through them and they can be installed any time.

 

A2DCA046-3F16-45AE-925F-87111C162E8A.thumb.jpeg.fc0183e622ffe6ed223de9f6e3f7a645.jpeg

 

A few hours were spent sanding the rails and then they were given a coat of w-o-p. 
 

B34AAB63-1B7D-410E-A751-72B925DCBC9D.thumb.jpeg.b88e5477f5036ae3817b561fdcd68429.jpeg


 

Been jumping back and forth between planking the front wall of the cabin and its roof.

 

 

 

58F4AC54-2A8F-4BFE-9C0C-3AA2EF952AA8.thumb.jpeg.b89ee380f20cfa7a75d6ce8e67d8f8c7.jpeg

 

415AE327-B243-4FE3-8702-A066FD44205A.thumb.jpeg.fa81da4cd6bc3c2d5e9b9e8ac0948126.jpeg

 

The three outboard planks of the roof were glued together before mounting because the first two planks run off the roof before they reach the last bulkhead/frame. A rabbet was cut along the bottom underside to lower the profile where the planks overlap.

 

B5039517-1A42-42EA-B22E-36DF59859F18.thumb.jpeg.b2768d77aa40a10cca041729200adc29.jpeg

 

E5C12902-D019-4A4C-A5AB-5EEEF9048ADA.thumb.jpeg.b1dc733cb3685b9b3f7d640c5469959a.jpeg

 

AEFB580A-BBC8-42B9-956B-BD01D164B96E.thumb.jpeg.f36a4087dc22c7ccb4e3ed08aa1e50ef.jpeg

 

 

 

Finger holes were drilled in the deck planks for removal. They look larger than they actually are. My rough estimate puts them at 1.5 - 2 scale inches 

 

A465F1EC-4F89-4100-81C2-881C630F13A8.thumb.jpeg.9aac1489c958d6f7e117780fa836ab5a.jpeg

 

For a change of pace the portholes were “ glazed “. Saw someone using this product but can’t remember who. Thank you. It works very well. Placed the portholes on plastic wrap (Handiwrap) and put four drops in each one. Can’t really see them well but here they are after curing for 24 hours.


D2DAECB5-BD44-4A32-AFFE-85877938B3C8.thumb.jpeg.0264e0bb3aa744b4be2cc0d51696f69f.jpeg

 

 

193F8061-90F6-4B68-9D0A-7671EC698A1F.thumb.jpeg.3bb36abfc5da79f223159dd9c73c2028.jpeg


 

Next will be finishing the roof and the front of the cabin.

 

 

 

Edited by Paul Le Wol

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

that half-lap jig is genius.  I assume there is fine sandpaper on the bottom face of the block.  Do you cut the shoulder of the half lap with the hobby knife and then sand up to it?

 

and how are you rabbiting your planks?

Link to comment
Share on other sites

Hi Cisco, thanks very much for your comment. For the half laps I scored the plank with a razor knife and used the knife to cut a notch back to the scored line. Then sanded the plank with that 3/8”x 3/8” block. The block has 220 grit sand paper stuck to it with double sided tape.

 

9EB3BDEF-A89A-4B44-9B49-6737ABB27ACA.thumb.jpeg.bdfa39bc915afe1916673cefd4e908a2.jpeg

 

8061446F-B109-48DA-A917-87A477DB99AC.thumb.jpeg.45071cd4d227a18903d477e1141d3b4f.jpeg

 

The rabbets are made pretty well the same way. The plank is scored with the razor knife and then a chisel is used to remove most of the wood. The sanding block is used to clean up the rabbet. I’ve been using the Mirka sandpaper that I picked up at Lee Valley. It hangs in there for quite a while 

 

4E1E372F-5525-47A4-80F7-C113F65940BA.thumb.jpeg.5471029d914d9a7cd5777be57c4f20ab.jpeg

 

92C2E3AC-2EC1-4CE1-A58E-C498C4B3AE37.thumb.jpeg.ccd7f944324a574fdf3bf3b6fba49b30.jpeg

 

62838A0A-2585-447C-A803-5BDEF7FE48A3.thumb.jpeg.67bae003ca14df0a1f096929a4f79515.jpeg

 

 

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

Hi Everyone, hope you all had a great weekend. Thanks very much to everyone for their Likes and Comments. The week was started by revisiting the portholes. Wanted to see what they looked like if they were blackened. It may have been because I didn’t wait long enough before glazing them but the next day the glazing had reacted with the blackener and turned blue around the edges. Going to leave the portholes brass.

 

403B30E7-6759-4113-9B12-73753649C884.thumb.jpeg.bfa8a40f590ead034f70301c601e0b78.jpeg

 

B9A68C2B-9B69-4FED-BF26-7B0FCA8DCF08.jpeg.6f81e32b7b0cbd8e4c737401d1fcccee.jpeg

 

Continued planking the cabin roof. Should have pre-painted the planks where  they overhang the front of the cabin right from the get go but I wasn’t thinking.

 

C9CE4B1F-E9D0-43B3-86EA-429180EAC70D.thumb.jpeg.0927a6545be8a65a5bd4e84a476e10e9.jpeg


 

F02651B5-A05F-4603-935D-8FFD407ECC09.thumb.jpeg.739068d14b24eb0bf8868675f14c2871.jpeg


 

6B60D9C9-BC98-414B-9D82-1E9D39733205.thumb.jpeg.801a0b4176835799c122909d38df1d34.jpeg


 

27E78FCD-6A20-402D-B088-6820DE07DFDB.thumb.jpeg.1a9c9d11336251a2e9998cd868433b85.jpeg

 

F260F5B5-6069-4E4D-9197-34FC6E4D7F4B.thumb.jpeg.7bb2c646e4b5a49260388c1a94c299b8.jpeg


 

1C3E9A4A-9709-45FB-B3CE-CA5C812DEAB2.thumb.jpeg.5e8d26b21943268e23be7bec32e03264.jpeg
 

Sanded for a couple of hours and then applied the first coat of Tamiya Dark Iron to the roof. Also resumed planking the front wall of the cabin.

 

C2ABBCE7-B83B-4E07-950A-C9AFD2F798AD.thumb.jpeg.a4d569f7b40af5d2acab27ea7645dc11.jpeg

 

21619752-736E-4D6B-8834-04BBB7B6B31E.thumb.jpeg.291528d515c76847d6ce26d33ec34b1b.jpeg

 

Second coat of paint to the roof and finished planking the wall.

 

18F81A4F-385A-4B83-914C-639124891DB6.thumb.jpeg.06e1ebcbfffe5f28ab58b9359f08aa28.jpeg


 

23D82DBB-66D4-4629-A157-930793023F26.thumb.jpeg.97cb9c4163fd7794566527bb69a6b005.jpeg

 

Opened up the holes for the portholes and gave the roof a third coat of paint.

 

D5E1D71D-2178-497F-9C39-EC3F923BE493.thumb.jpeg.ea8d6e5909b6f9a70f305832197810c1.jpeg


 

9B894C0C-F2E1-4FDE-9D14-59657152E765.thumb.jpeg.03a41111b0533a44101cf44489c3bbd8.jpeg


 

AF25A7D8-17E4-4EFF-B568-40BA55B5F9D4.thumb.jpeg.9b35de5885c9fe4d5a83f4e134e3b1e1.jpeg

 

Moved down to the bow and started shaping the last frame/bollard out of pear.

 

7A0D083D-18E8-49F4-A833-873545113D73.thumb.jpeg.10333c375281f4d44756524dce00991c.jpeg

 

Next will be finishing the bow. Hope you all have a good week.

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

Hey Everyone, I hope your week went well. Thanks so much for dropping by and for the Likes. Spent the week adding small bits and pieces starting with the braces that are mounted inboard of the grommets for the clew rigging. Made new ones out of pear.


 

D38ACDE5-3C54-474B-85CC-3E378F3AB4AE.thumb.jpeg.0b56f828835e7106a3c40f6162836d34.jpeg

 

They were mounted and the hole was drilled through the plank.

 

5298D7B6-C3BC-4617-B7FE-36F7C6728B6A.thumb.jpeg.dc2afb221fb3c81d50fd1cb634e0e6eb.jpeg

 

The drill bit was used as a guide to glue the grommet to the outboard side of the plank.

 

20AC891E-4033-4319-89B3-32C293830DFB.thumb.jpeg.745559102c6f0ad9e5c234a550f43404.jpeg

 

 

BAFB278C-72F9-42CD-B2F6-9A8662D4D5C6.thumb.jpeg.43cb6931229c00689a2f2f0d7131acfd.jpeg

 

A plate for the hawse hole was made from 1/4”x 3/64” strip

 

 

F6E0B718-DC7F-4BD1-906B-90FE9A51A0EE.thumb.jpeg.14016ba04621c6c73195a0cbd4a9ab69.jpeg

 

 

78507BCA-7166-45B1-82EF-9DAA307FBF58.thumb.jpeg.0a04501304cc97dddc4687515069a832.jpeg

 

 

I picked up a bag of aquarium pebbles at the Petsmart and used them for ballast. Glued them in with E6000 adhesive.
 

 

640E5BB6-3244-40FF-A1AB-90EE1C41234C.thumb.jpeg.19052abc3a6844a8ddfc0068baf65352.jpeg

 

 

552C83AA-BEBE-4716-AAA3-FADE1F9A0C54.thumb.jpeg.7d7c1e4aed245219a3f119e02af89023.jpeg

 

 

The portholes were installed along with knee braces on the front of the cabin wall. The belaying pins were shown in the plans as being flush with the top of the horizontal part of the rail but I decided to bring them up a little higher 

 

 

EDF7F058-A269-460B-9E85-FAD7C7C19919.thumb.jpeg.a5d361aa7b10900c3bdfccd3013c954a.jpeg

 

 

9AFFE9B7-630C-4410-9846-7F6D78AFDBF0.thumb.jpeg.fe539d16b983ba8318e120ee98257c8a.jpeg

 

 

Then finally I started the chainplates. The plans show them being mounted though a hole in the rail but but mine were faked. The Billings parts ( on the right ) didn’t seem wide enough to drill a mounting hole in them so I used 1/16” brass strip. One end was bent to hook under the sheer strake ( as shown in the plans ) and the upper end was filed to a sharp edge so that it could be pushed up and under the trim strip beneath the rail.

 

 

469B1F26-0F52-452E-B92B-6E074BD19668.thumb.jpeg.df67144df24d1e343a7445b2459aa7d6.jpeg

 

 

 

 

 

F067E29D-83AC-41D9-ACE9-FBF022C188E2.thumb.jpeg.6220640f083528ee39acc7cf4ca4224a.jpeg

 

Each strip was pushed into place to make a notch in the trim piece then removed and annealed. A hole was drilled and then it was blackened. Eye bolts will be mounted in the rail above each chainplate. A bit of CA was used to secure the nail in the hole.

 

 

3D02EF01-48AC-404A-A329-F829D392DD03.thumb.jpeg.660cadc62c2154903718e5b809ca9987.jpeg

 

 

D0A1FA80-17D6-4C59-A633-7F92B3A88B2D.thumb.jpeg.bf5f9ac7b79f1ba0da408a5615079175.jpeg


 

8D4EA84F-1278-4290-9F47-E570D5F876E0.thumb.jpeg.3537a06434d4edc3a10f1170c4140721.jpeg

 

 

768EC4E1-E664-4F1A-B336-94C544B9F107.thumb.jpeg.6b21d235036cbc122e19304a0830525f.jpeg

 

 

Next comes the rudder and a stand. See you then. 

 

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...