Jump to content
Bahamas Diver

Niagara by Bahamas Diver - Model Shipways

Recommended Posts

I will be attempting to re-construct this log over the next few weeks.

 

 

The US Brig Niagara or the Flagship Niagara[a], is a wooden-hulled brig that served as the relief flagship for Oliver Hazard Perry in the Battle of Lake Erie during the War of 1812. It is one of last remaining ships from the War of 1812. TheNiagara is usually docked behind the Erie Maritime Museum in downtown Erie in the U.S. state of Pennsylvania as an outdoor exhibit for the museum, but travels the Great Lakes during the summer, serving as an ambassador of Pennsylvania when not docked. It was listed on the National Register of Historic Places in 1973 and was designated the official state ship of Pennsylvania by the Pennsylvania General Assembly in 1988.

The Niagara was constructed from 1812 to 1813 to protect the vulnerable American coastline on Lake Erie from the British and played a pivotal role in the battle for the lake. Along with most of warships that served in the war, the Niagara was sunk for preservation on Presque Isle in 1820. Raised in 1913, it was rebuilt for the centennial of the Battle of Lake Erie. After deteriorating, restoration of the Niagara was started again in the 1930s, but was hampered by the lack of funds caused by the Great Depression and remained uncompleted until 1963. A more extensive restoration was carried out in 1988 in which much of the original ship was largely destroyed. The incorporation of new materials and modern equipment makes it ambiguous as to whether it is or is not a replica

 

A picture of me (in the middle) while working as a volunteer sailor on the Niagara, with the decedents of Oliver Hazard Perry.

 

 

post-749-0-81749300-1361127111_thumb.jpg

post-749-0-12727700-1361127165.jpg

Edited by Bahamas Diver

Share this post


Link to post
Share on other sites

Thanks Patrick.  This is going to be an interesting task...rebuilding a log.  Like you, I am probably going to only up load pictures as I have been working on my Niagara since September 2010.  :rolleyes:

Share this post


Link to post
Share on other sites

Hi David

Great to see you back.

That is at least 3 Niagaras up and running !!

 

Regards

Ken

Share this post


Link to post
Share on other sites

the hull was time consuming but fun.  The difficulty of this model is that it is single planked.  This means the the ends of each plank must be attached to a bulkhead, making the staggering of the planks bit more difficult.  On the other hand, because the hull gets painted some errors in planking can be covered up with paint.  

 

After the hull was planked I filled in any gaps by laying a thin line of white glue in the gap and then sanding over the area.  This let the sawdust from the sanding attach to the white glue and fill the gap.

post-749-0-00118700-1361133657_thumb.jpg

post-749-0-13058100-1361133660_thumb.jpg

post-749-0-36104700-1361133662_thumb.jpg

post-749-0-18308800-1361133665_thumb.jpg

post-749-0-75070100-1361133805_thumb.jpg

Edited by Bahamas Diver

Share this post


Link to post
Share on other sites

Looks like a great start, and progress. I have the kit, but I am currently about half way through the Lauck Street Fair American. I figure I will be on to the Niagra by July, so I would love to hear about any 'gotcha' errors you found in the kit or instructions. I have never done single plank on hull yet, and that is the part I am the most nervous about.

Did you have any problems with wood quality? Sometimes I find the MS quality is a bit lacking, especially in planking wood. I'm debating replacing all the kit's mahogeny for planking with wood from Hobby Mill.

Share this post


Link to post
Share on other sites

Hi Steve,  I know I had a number of gotcha's but I am having trouble remembering many of them.  As for the wood quality, I had no troubles with it.  There is no   mahogany as I recall.  Since nearly everything is painted (thee is not much that is stained or left "bright" it is not necessary to buy other woods.  If however, you are not going to paint your model, then getting better quality woods would be a wise idea.  When you start your Niagara Build Log, I'll follow it.  If i think of things as you progress I promise to comment on them (esp. the gotcha's)

Share this post


Link to post
Share on other sites

Nice build.  I thought the use of manila folder for building the boat planks was brilliant!  I've never been able to get a nice clinker built look.  Your's looks great. I'll try using that material in the future.

Share this post


Link to post
Share on other sites

David, it's good to see you back up on MSW. Thank you for the offer to help, Your stern photos are exactly what I need to determine where I need to make corrections.

Edited by lb0190

Share this post


Link to post
Share on other sites

Thanks Sjors.  ;) .  I have jury duty this week so depending on whether or not I am picked I will attempt to finish rebuilding (or at least adding pictures to) my log.  I feel so depressed...I was a commander or captain before the crash...now I have been demoted!   :D hehehehe.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Recently Browsing   0 members

    No registered users viewing this page.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem

Modelshipworld - Advancing Ship Modeling through Research
×
×
  • Create New...