Jump to content

Recommended Posts

I'm getting ready to plank the hull of my Corel Shenandoah cutter. In Chuck's planking article he says that he uses art tape for lining off the hull. What is art tape and where do you find it?

 

Thanks!

 

Steve

completed models:

Shenandoah (Corel)

 

waiting on the shelf:

La Sirene (Corel)

Half Moon (Corel)

Puritan (Mamoli)

 

 

 

Patsy (derisively): "It's only a model."

Arthur: "Sshhh."

 

 

 

Link to comment
Share on other sites

Just a thought, be carful which one you get.

I had tried a thin colored tape from Hobby lobby but found if it stayed on too long some of the color transferred to the wood and had to be sanded to remove. It may have been left on too long, or pressed on with too much pressure but it did end up making more work.

I suspect I may have bought the wrong type. I suggest testing it on scrap before using on the build.

Richard.

Richard
Member: The Nautical Research Guild
                Atlanta Model Shipwrights

Current build: Syren

                       

Link to comment
Share on other sites

I don't know if this what you're looking for but try this

Also look at this

Edited by riverboat

completed build: Delta River Co. Riverboat     HMAT SUPPLY

                        

                         USRC "ALERT"

 

in progress: Red Dragon  (Chinese junk)

                      

Link to comment
Share on other sites

Thanks everyone for the suggestions. Yes, it was art tape. There's an art supply store near me that I'll try tomorrow.

 

Thanks again!

 

Steve

completed models:

Shenandoah (Corel)

 

waiting on the shelf:

La Sirene (Corel)

Half Moon (Corel)

Puritan (Mamoli)

 

 

 

Patsy (derisively): "It's only a model."

Arthur: "Sshhh."

 

 

 

Link to comment
Share on other sites

I tried the art supply store and they had never heard of the stuff. Then I ran over to Staples and they had it. If any of you try to find it there, it's not with the rest of the tape--it's in the poster making section.

 

Steve

completed models:

Shenandoah (Corel)

 

waiting on the shelf:

La Sirene (Corel)

Half Moon (Corel)

Puritan (Mamoli)

 

 

 

Patsy (derisively): "It's only a model."

Arthur: "Sshhh."

 

 

 

Link to comment
Share on other sites

Hi there Steve,

 

I ran into a little trouble painting my ship, even using the most expensive masking tape I could buy at the hardware store.

 

It was recommended (and endorsed by a few others) that I use Tamiya Masking Tape which may be a little dearer but sounds like it works really well.  My roll hasn't arrived yet so I can't confirm it but I really trust these guys!

 

I hope that is some help to you too!

 

 

Bindy

Link to comment
Share on other sites

Thanks for the recommendation, RMC and Bindy. I'll certainly try the Tamiya tape when I get to the painting stage. How dear is it, Bindy? I think clean lines would be worth a bit more money.

 

I'm going to use the art tape for lining off the hull to plan where the planks are going to run. I figure this roll is going to last me a long time.

 

Steve

completed models:

Shenandoah (Corel)

 

waiting on the shelf:

La Sirene (Corel)

Half Moon (Corel)

Puritan (Mamoli)

 

 

 

Patsy (derisively): "It's only a model."

Arthur: "Sshhh."

 

 

 

Link to comment
Share on other sites

Link to comment
Share on other sites

Tamiya is great tape for painting.  But it is much like ordinary masking tape in 'feel'.  The Artist's Tape is almost plastic in feel and can take curves very well.  For lining a hull I'd go with Artist's tape.

Augie

 

Current Build: US Frigate Confederacy - MS 1:64

 

Previous Builds :

 

US Brig Syren (MS) - 2013 (see Completed Ship Gallery)

Greek Tug Ulises (OcCre) - 2009 (see Completed Ship Gallery)

Victory Cross Section (Corel) - 1988

Essex (MS) 1/8"- 1976

Cutty Sark (Revell 1:96) - 1956

Link to comment
Share on other sites

Thanks Augie and David.

 

Steve

completed models:

Shenandoah (Corel)

 

waiting on the shelf:

La Sirene (Corel)

Half Moon (Corel)

Puritan (Mamoli)

 

 

 

Patsy (derisively): "It's only a model."

Arthur: "Sshhh."

 

 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...