Jump to content
dafi

HMS Victory by dafi - Heller - PLASTIC - To Victory and beyond ...

Recommended Posts

Thank you Jan :-)

 

... and here I go again ...

 

... the blocks ...

 

... as discribed before punched with the scribing needle, drilled ...

 

800_Victory-blocks_9214.jpg

 

... one side already rounded ...

 

800_Victory-blocks_9220.jpg

 

... and after putting to lenth trapped underneath the finger´s nail to get the opposite side rounded ...

 

800_Victory-blocks_9222.jpg

 

... and like shake´n´bake we got some nice great little itzy-bitzy-teeny-weeny sweet blocks :-)

 

BUT! Stop Press!

 

First I was not in a mood for the messy story with the dying stuff and second, isn´t there a better way ?!?

 

Tja ... that´s dafi ...

Share this post


Link to post
Share on other sites
... didn´t dafi already make these nice little blocks from wood !?! No messy dying and so on?.

 

So I tried a simplified version. Prepared two wooden battens accordingly in  1 x 1 mm und 2 x 1 mm - made a distance holder into the drill stand for the distance to the edge and pushed the batten upwards (green) and then moved according to the red mark to the side. 

 

800_Victory-tackles_9230.jpg

 

For the double block still turned 180° and did a second round. Works rather fast :-)

 

800_Victory-tackles_9232.jpg

 

Then some bondage with Sello-Tape ...

 

800_Victory-tackles_9235.jpg

 

... and lenghtened with grinding disk which does not create splintering ...

 

800_Victory-tackles_9212.jpg

 

... and unpacked.

 

Then empaled the blocks on a old 0,5 mm drill ...

 

800_Victory-tackles_9195.jpg

 

... and cleand and rounded the corners ...

 

800_Victory-tackles_9197.jpg

 

... bound a thread onto one of my etch hooks and glued it well centered onto the back side.

 

800_Victory-tackles_9198.jpg

 

Then a knot and some glue on the other side ...

 

800_Victory-tackles_9200.jpg

 

... shortened the short side of the tread ...

 

800_Victory-tackles_9202.jpg

 

... and ready the single block :-)

 

The same for the double block, just both ends cut.

 

800_Victory-tackles_9206.jpg

Share this post


Link to post
Share on other sites
Made a small scale to measure the required length ...

 

800_Victory-tackles_9256.jpg

 

... and put the blocks into my serving machine. The compass allows easy reading of the required length.

 

800_Victory-tackles_9259.jpg

 

Fitted the lanyards, fixed with glue ...

 

800_Victory-tackles_9263.jpg

 

... and wrapped around.

 

800_Victory-tackles_9265.jpg

 

Looked strange and impracticable, so decided to consult the literature again. Then tried a final wrap in the middle and ended up with no major wrapping, just a big loop and some minor wrapping in the middle. Looks much more logical.

 

800_Victory-tackles_9275.jpg

 

The the final assembly on the trucks and it finally worked the way I wanted!

 

800_Victory-tackles_9287.jpg

 

So after months of no sleep, dafi finally will have a good rest tonight :-)

 

Sleep well all of you and dream of me nicely ...

 

... that is what one could call nightmares ;-)

Share this post


Link to post
Share on other sites

I notice that you didn't put eye bolts in the bulwark....not that it matters,  but i figured I'd mention it  ;)    a lot of detail.......and you still have quite a few cannons to fit out.  they will look really good though,  once your finished.   great work Dr. Dafi!

Share this post


Link to post
Share on other sites

Thanks Mark and got me Popeye ...

 

That was the corner that was too tricky for wanted result: it will not show to apparent on the pictures :-)

 

This is just a omission for the lower decks, visible guns will be fitted properly, promised!

 

Dr. dafi

Share this post


Link to post
Share on other sites

folks like us.......we'd be all over it  :)........but the normal person looking at her wouldn't think in that small a detail.  the cannons visible from the spar deck would need to be done ........I like it....looks great!  yepper.......needs to be some sort of rigging to hold those buggers in place!  ;)

Share this post


Link to post
Share on other sites

Well, I guess I'll be following along another cool WIP thread here. I just purchased this kit at a price that I couldn't refuse and then I found a toy donkeys head under my pillow... :D family played a joke because we just got done watching Godfather series on TMC?? on TV. Anyway, you're doing great I'm already picking up a lot of useful information. I tell ya, this website as whole is a gold mine  :10_1_10:

Mike

Share this post


Link to post
Share on other sites
Thank you very much :-)

 

... so easy going tackle knitting watching Sanctuary on TV ...

 

... goes down the hand easily ...

 

... or better saying the serving machine :-)

 

800_Victory_tackles_9290.jpg

 

XXXDAn

Share this post


Link to post
Share on other sites

Great mods and redo's.  I love what you have done.  I use that same copper tape..have so for over 35 years.  It is wonderful.

 

Thanks for posting...great combination of wood and plastic. Looks superb.

 

 

Rob

Share this post


Link to post
Share on other sites

*blow*

 

*cough*

 

... only been away for 57 years and already that much dust?

 

*think*

 

What was my favorite pass-time here?

 

*scratichingthebeard*

 

Oh yes, there was someting - DEMOLITION!!!

 

800_Victory_side-entry_0169.jpg

 

... okokokokok ...

 

... I know, that the side entry port was already "finally" fixed, but it was stronger than me :-)

 

...hihihihihihihi...

 

XXXDAn

Share this post


Link to post
Share on other sites

To be honest ...

 

... I do personally strongly believe that there is more evidence that it was not there than those that it was. :-)

 

But it is a too nice feature to be omitted in the build - so I took some castings to add to my resin parts.

 

XXXDAn

Share this post


Link to post
Share on other sites

To be honest ...

 

... I do personally strongly believe that there is more evidence that it was not there than those that it was. :-)

 

But it is a too nice feature to be omitted in the build - so I took some castings to add to my resin parts.

 

XXXDAn

I too have thought long and hard about this. My conclusion was that I think the entry ports were there, but the top and bottom were built up to resemble the adjacent gun ports when out of harbour, and perhaps even a 'jury lid' made, ready for a lengthy sea commission. However, all the records show that the middle gun deck had 28 cannon, and not the 30 of the decks above and below. Could the captain have ordered an extra two cannons while the ship was being victualed - thus not being shown on official records?

Share this post


Link to post
Share on other sites

I never had the time to do a complete research in the NMM.

 

It looks to me that the entry port disappeared somehow from the drawings in the 1780´s (because of wartimes - American War of Independence?) and just reappeared in the 1805´s.

 

A complete survey of all the three decker´s plans and models should perhaps clarify this and especially the dates. Another thing is, that the plans just show the starboard side and remember that at one point the ports were only on the port side. Does not make things easier ...

 

So I enjoy the bit of artistic license ;-)

 

The other thing is the question of how these ports was shut. So far - even with the help of the board here - no strong hint was found. All model that I found so far lack a door. 

See more:

http://modelshipworld.com/index.php?/topic/333-side-entry-ports-on-british-first-and-second-rates/

 

XXXDAn

Share this post


Link to post
Share on other sites

It is surprising, isn't it, just how many details on this ship are in grey area territory.

 

If the ports were present, I am pretty sure the men would have used some kind of ad-hoc method of covering it/them - canvas, leather or wood perhaps.

 

But the question remains, why only 28 cannon for the middle deck? They were certainly designed with the entry ports in mind, I think. But in the real world, in the midst of all out war, long blockades and thousands of nautical miles away from home, I guess anything goes.

Share this post


Link to post
Share on other sites

That too is my opinion, the 28 guns are one of the strongest hints for the port. At no time that were 30 guns recorded in the books, for me a "must" if the door would have been replaced by a gunport, otherwise the first two or the last gunport would have been idle.

 

At least for bad weather there must have been a cover, and in my opinion not only canvas or leather.

 

But that is the interesting bit on this ship: Although believed to be that well explored and boring and a hundred thousend times being build - there are still so many open questions. And I love to stir a little bit in that pot - a friend of mine would call it "fascinating" ;-)

 

XXXDAn

Share this post


Link to post
Share on other sites

As I always like to visualise and try out my thoughts, here are some versions on a mere speculation basis. 

 

Single board on the outside

Victory-130807_0201.jpg

 

Half doors opening outside:

Victory-130807_0205.jpg

 

Single board on the inside:

Victory-130807_0202.jpg

 

Half doors on the inside (like quarter galleries)

Victory-130807_0207.jpg

 

 

... just works out on the inside.

Victory-130807_0208.jpg

 

And a version like on fire ships as seen in construction and fitting: Half board on the bottom and half lids on the upper half.

Victory-130807_0210.jpg

 

Cheers, Daniel

Share this post


Link to post
Share on other sites

Just a thought... If you go with a door, typically ship's doors open outwards so that water pressure would force the door tighter into it's frame (just like the gun ports), making it easier to keep weather tight.

 

A door opening inwards risks getting blown open by the first wave that decides to crash the party. ;)

 

 

Andy

Share this post


Link to post
Share on other sites

As for my personal opinion seeing those tests: I also would discard the inside board for the same reason Andy gives. The half lid doors are one more gap that could leak, on top the inside half doors have a slight problem with the deck because of the thumbledom and a even bigger one because of the hanging knees, that prevent opening more than 90°.

The fire ship doors is a too sophisticated feature and I believe it would have been shown.

 

The "single outside board solution" would give some intersting thoughts. It just requires battens or a small recess like the gun ports inside the opening to be pressed /pulled against. This could be done by some eyebolts and some simple lashing from the inside. As it is not part of the structure and not a permanent fitting, this could explain why it is never represented in the models - it was seen as a mere board. Another hint could be the panelling of the inside of the door frame, this one looks much more like an internal fitting than an outside part of the ship.

 

But as mentioned before, these are pure speculations, hard proves still missing. But perhaps it allows to get a closer idea, what we are searching for, like special construction details. The only thing I found so far is, that NMM´s plans of Nelson and Caledonia show the usual gunport arrangement of eyebolts around the entry port, as if this port also was used for guns on occasions. And seen the concave outside of the hull, those breeching-eyebolts in the middle would already guarantee a secure lashing of the board against battens or recess ...

 

 

Here still is a small color variation of my personal favorite:

Yellow door at the end of 1804 before Nelson took possession of her and ...

 

Victory-130807_0201.jpg

 

... after he introduced his checker on the port lids :-)

 

Victory-131007_0200.jpg

 

XXXDAn

Share this post


Link to post
Share on other sites

The question is: would Nelson recognise this entry-port....

 

There is a nice model in NMM showing Victory as she was supposed to be n 1803 without the entry-ports.http://collections.rmg.co.uk/collections/objects/66474.html

There is alos a model that shows victory as she was supposed to be in 1805 sith entryports and even a platform outside the hull....

http://collections.rmg.co.uk/collections/objects/66475.html

 

The one without is assumed to be the contemporary model

 

 

Jan

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Recently Browsing   0 members

    No registered users viewing this page.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem

Modelshipworld - Advancing Ship Modeling through Research
×
×
  • Create New...