Jump to content

Recommended Posts

LA GEMMA - Tartane ligure 1863 scale 1:50

 

THE model tartana Gemma on the basis of a plan of 1863 the shipyard Vassallo Sanremo.
The project is based on the book by Franco Fissore editions Ancre.
The original design for the 1/36 scale model construction as arsenal.
The design has been reduced in scale 1/50.
The tartan was a type of ship cargo for trade in the Mediterranean, armed with a sail that was used from 1850 to 1940.

post-15132-0-24944900-1422808089_thumb.jpg

post-15132-0-78586700-1422808112_thumb.jpg

post-15132-0-32815700-1422808136_thumb.jpg

post-15132-0-82120300-1422808174_thumb.jpg

post-15132-0-71504600-1422808223_thumb.jpg

post-15132-0-66015600-1422808259_thumb.jpg

post-15132-0-76058100-1422808289_thumb.jpg

post-15132-0-47384300-1422808303_thumb.jpg

post-15132-0-10460600-1422808307_thumb.jpg

post-15132-0-22830700-1422808310_thumb.jpg

post-15132-0-76611100-1422808313_thumb.jpg

post-15132-0-93013200-1422808317_thumb.jpg

post-15132-0-65817500-1422808320_thumb.jpg

post-15132-0-42471700-1422808323_thumb.jpg

Edited by iosto

Share this post


Link to post
Share on other sites

The hull has been achieved by combining a keel plywood and the ordinate birch, between the spaces has been inserted in the balsa wood.
After the surface has been smoothed and plastered with filler body repair shop.
Later was performed coated by plating 0.5 mm.
Later before mounting the handrail, was built a underbridge with plywood end then covered with strips of 0.5mm.
Between a strip and the other is concerned inserted twine black to have the effect of caulking.

Share this post


Link to post
Share on other sites

Then I built the gunwale, and on this I drew a line parallel to the outer surface to mark the line on which to place the bulwarks stanchions.
I run on the line of the holes and enter their bulwarks stanchions.
were later mounted the boards of the sides.
Then it was later realized the gunwale.
The hull filled and honed, was treated with a gray primer tamyia, and after with a primer fine tamiya white, to prepare the base for painting.

Share this post


Link to post
Share on other sites

Wonderful work. Please post photos of the hull planking.

 

Greg

Unfortunately I have no pictures of the beginning of the construction, as have been lost.

Below I will post the sequence of construction from this point.

The model is now almost finished, I have to finish some finishing touches and the lifeboat.

a greeting

Iosto

Share this post


Link to post
Share on other sites

Construction of 'mast

The mast was made by gluing three strips of wood Douglas, getting a single strip square.
The base and the summit were maintained properly reduced square section.
The central part is made of sata first octagonal section and then round.

post-15132-0-31853300-1422810668_thumb.jpg

post-15132-0-07135200-1422810682_thumb.jpg

post-15132-0-22815900-1422810685_thumb.jpg

post-15132-0-42874000-1422810688_thumb.jpg

Share this post


Link to post
Share on other sites
 

Construction of the boat
I made a form balsa, and the profiles of plywood for the keel and for the border.
On the line of ordinates were made to enter the holes arranged in plastic card.
He was subsequently glued planking.
A coating occurred, was detached from the model form.
After sate are attached tables outside and realized the dunnage benches and oars.
Subsequently, the model has been plastered, smoothed and then sato applied primer gray and white.

post-15132-0-37838600-1422812334_thumb.jpg

post-15132-0-01820000-1422812342_thumb.jpg

post-15132-0-44853700-1422812353_thumb.jpg

post-15132-0-71645700-1422812357_thumb.jpg

post-15132-0-28388200-1422812377_thumb.jpg

post-15132-0-09356200-1422812384_thumb.jpg

post-15132-0-41175700-1422812391_thumb.jpg

post-15132-0-27457300-1422812404_thumb.jpg

Share this post


Link to post
Share on other sites

Coloration of the sails
The sails are made of cotton, and left to soak in the order to give a similar staining to reality.
The sail has been dyed with red ink fuchsia
to the edge of the sails was glued with the glue rapid a lanyard.
Were embroidered eyelets, and added the rings.

post-15132-0-36392300-1422812740_thumb.jpg

post-15132-0-09869500-1422812752_thumb.jpg

post-15132-0-11874100-1422812763_thumb.jpg

post-15132-0-25014600-1422812768_thumb.jpg

post-15132-0-99266000-1422812782_thumb.jpg

Share this post


Link to post
Share on other sites

Great detail and a beautiful boat.  Well done.

 

Bob

 

Thank You!

I hope to post more photos of the finished model soon.

Hello

 

Iosto

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Recently Browsing   0 members

    No registered users viewing this page.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem

Modelshipworld - Advancing Ship Modeling through Research
×
×
  • Create New...