-
Posts
2,305 -
Joined
-
Last visited
Reputation Activity
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
Little progress:
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
I finished the installation of the courses between the doors and started to finish with fine sandpaper to remove the glue residue and the excess of black cardboard. I also finished the edges of the gunboats and scuttles the oars.
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
more photos
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
I continued with the bandage of the topsides, I realized I had made a serious error to paste the thresholds of the gunboats: the angle between the threshold and the side wall is pretty sharp and this did not allow for a perfect installation of the course below thresholds, for obvious reasons, leaving a little 'air.
I removed very carefully thresholds and set the course and the joints redone, everything went perfectly, although I remove a threshold, have resulted in the rupture of an oarlock to the coast, but this will not be seen because it will be covered by the plating .
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
some photos
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
Thank you!! :)
Small forward: I set the molded course on the left side and I started to wrap the starboard side starting with the two courses between the moldings at the stern, ebony
This is my "powerful" cutting tool for the oarlocks of double coasts:
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
more photos
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
Now it begins to outline the final form of this corvette, at least on the starboard side: I fixed the piece of plank molded bow, prepared and glued the other strip molded, smaller, which limits the performance of the formwork and I started to cut and trim oarlocks of double coasts
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
Before continuing the work inside, I decided to finish the topsides on the outside because I want to remove all the bolts that cause me many problems and hassles by cutting the excess coast and finishing on the gunwale.
I then prepared the tool, converted from an old saw blade and molded with a small disk, for the course that I started to fix
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
I finished the gunboats also from the inside
I also fixed the sleepers of the castle
I also started to prepare the battens of flowers: job rather difficult to prepare, especially because you do not have much space to be able to score perfectly all measures
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
Today I finished working on the gunner. I have completed the thresholds and lintels.
This is the window of the cabin of the Captain
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
I finished opening the gunboats and I started to prepare the thresholds, which have a particular concavity, to which I have built a custom "tool"
this is the tool:
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
more....
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
Thank you!!!
I finally fixed the last beam formwork, which fits into the oarlocks of the transom:
Meanwhile, I continued working on the opening of the gunboats of the bridge and the openings for the scuttles of the oars; for them I made a template sheet to try to make them all equal
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
I finished the keelson, and then I started laying dormant bridge
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
I finished the work on the belts, I started the long process of equalization of the interior of the coasts, and if it was tough on the outside, inside it is even more!
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
I have finished the belt of the left side The second belt on the right side
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
I also positioned the second belt on the left side
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
Today I continued to work pasting the strip between the two belts
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
after removing the clamps here is the result
on the right side
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
other photos
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
I started fixing belts
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
I placed the planking of the bottom of the transom, must, I think, before tightening the belts.
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
Thank you!!!.......
In order to block the stern oar in a more stable manner, on the excesses of the oarlocks I have tentatively set a provisional "crowning glory" that I will take away when I have completed the transom
-
NMBROOK reacted to giampieroricci in L'Amarante 1749 by giampieroricci - FINISHED - 1:30 - French Corvette
Thank you, friends!
Slowly the work going on, I started the construction of the transom: of course is yet to block and finish, especially the two stern oar that for security (or insecurity) I made them abundant