Photo Bud

My apologies to those who have supported me in this and have encouraged me, but medical issues have brought me to a standstill, both physically and mentally. I'm hoping after my next set of procedures, I can get back on track with both ship modelling and HO train modelling. Until then I take comfort in watching this forum and occasionally adding my two cents worth!

My apologies to those who have supported me in this and have furnished me with the necessary instructions (especially @Veszett Roka), but medical issues have brought me to a standstill, both physically and mentally. I'm hoping after my next set of procedures, I can get back on track with both ship modelling and HO train modelling. Until then I take comfort in watching this forum and occasionally adding my two cents worth!

Perfect, printing it out now! THANKS!

Sorry I didn't answer sooner, but this will be a static build.

These are most appreciated. Will make good use of these!

That would be great, thanks! Mostly need the rigging chart, not the part list.

Not much progress to be seen, but it took quite awhile to untangle the standing and running rigging at the bow! And yes, the bowsprit is not down in its proper place while bonding hull halves at the top.

Some more detail of work to be done. First, overall look at bow where most damage done. Note that hull has split into it's two pieces, flying jib has come loose at top (sail actually broke at tip), and lines are entangled. Also, the ship's boat shown has to be put back on its storage location farther aft. Detail look at bowsprit and jibboom. Note that it was broken once previously and repaired by drilling hole and inserting part of a straight pin which was insufficient to prevent new damage. Pin will need to be straightened and reinserted before gluing again. Now, the aft side of foremast showing tangled lines and unattached shrouds. Finally, the unattached spanker aft.

I like the thought of the ship, but not looking for long, complex build, nor a larger model, though it would be cool. Relatively quick, and dirty, and easier to put on a shelf. Thanks for the vote of confidence on this particular model though!!!!

I'm thinking of getting a 1/350 Flower Class Corvette, "HMS Zinnia", and have found one where box is marked "Mirage Hobby" but seller identifies it as "Dragon Models USA" at only about $24 (US). I have two questions. Does anyone know about the quality of this one? Is there a better one out there (at about the same or moderately more cost)? I had decided on this one since it is an early (1940) version of this class and more in line with the book and movie, "The Cruel Sea". Thanks for any help you can give!

An old model of a Sturmgschutz III, can't remember if it is an Ausf. B or E. Along with a scratch built bridge of balsa and styrene.

I especially liked your pictures of the Flower class corvettes as one of my favorite WWII naval books is "The Cruel Sea" by Nicholas Monsarrat. The (badly worn) cover of my copy from 1951 had the cover designed by John O'Hara Cosgrave II. I have to say, I prefer yours!

I am absolutely blown away by your artistry. I have spent a large portion of my morning going through these pictures and will need to do it several times more. The detail and color you get from these water colors is magnificent! I am in awe. Thank you for sharing your talent.

This model is probably 40 years old, many years ago it took a dive off a 7 foot book case and I couldn't bear to part with it. Now I'm going to try and repair it. With my rekindled interest in ship models, it only seems like the right thing to do! Here you can see much of the damage done, in addition to the hull halves separating and the deck becoming loose.

I have the tools, now just need the skills! That Cutty Sark is from decades ago that took a deep dive off a bookcase many years ago, maybe to finally be resurrected.

Wondering if these clamps are the best way to hold strakes in place during build?

A new beginning to an old project. I acquired the Amati Endeavour around 2005, let it sit for awhile and then started it, only to drop it again after minimal progress. Here is the kit box. Got the bulkheads installed, deck base added, and started mast tapering (seen on the grooved board I used to keep it straight over the years). Sorry for the messy area, but the desk will need to be cleaned of model railroading stuff before I restart this project! lol btw - The tools alone were "almost" worth the cost of the kit. Used several of them over the years for other modeling tasks!

Just downloaded this and it seems really great, but I can't find figures 1 or 2, although there is a 2A, B, and C. Should I assume figure 2 is the sum of the 3?

Photo Bud here, living in Elk Grove Village, Illinois, United States. I have been interested in building a ship model for almost two decades and have accomplished almost nothing! I have built many plastic airplanes, helicopters, and ships of all sizes including a Revell Cutty Sark that came out pretty good, but suffered a 7 foot (2 meter) fall many years ago but I still have 'cause I can't bear to throw it out. I'm also a model railroader of many decades. In addition, I've been dabbling in Raspberry Pi and Arduino electronics. So a jack of many trades, but master of none. Back in 2004, I joined the email list of Seaways Ship Model List (and even recently got some new emails from it about buying and selling kits). I bought several kits around that time and must admit my first goal was to build a Constructo Cutty Sark which I have always loved, but one look at it made me realize there was no way I would ever attempt to build it with my limited skills. I had also bought a Model Shipways Dapper Dan with the intent to make it sort of look like an HMS Surprise but when Mamoli came out with their version, bought that one too. After buying those, and realizing I would not be able to do them justice, I bought both an Amati Bluenose and an Amati Endeavor, hoping they would be good learning models. I started the Endeavor and got the bulkheads installed and shaped the mast and then got cold feet when it came time to adding the strakes. I'm hoping that this forum and some of the videos available here will get me off backside and make some progress. Please bear with this novice as I attempt to learn and do. John (aka Bud aka Photo Bud)

This statement fits me to a tee. I got interested back around 2003, bought models and ship building books. Joined the Seaways Ship Modeling list back in 2004 (and recently got some new emails from that list). Watched some videos and froze up. I want a planked ship and the whole planking thing never made sense and after overthinking it, dropped the idea. I'm hoping that I can break that mental block now. I started the Amati Endeavor and got the bulkheads in place and shaped the mast, then stopped after reading (and re-reading) the explanations of how to shape the strakes and throwing up my hands in defeat. What I really need is to sit down with a real person who can show me how this is done. Unfortunately, with Covid, this probably won't happen soon and I will try to find some youtube explanations and demonstrations that can help me. So, bear with me as I lurk and hopefully ask some really novice questions.