Jump to content

MONTANES by Garward - OcCre


Recommended Posts

The knot of drive is made on description (photo 8 – 11) and drafts, by developed Boris B. This construction, to my mind, combines in itself dignities of direct drive and strap transmission, simplifies assembling and regulation of knot, and also does not make noise practically.

Description of Boris B:

http://www.shipmodeling.ru/phpbb/viewtopic.php?f=10&t=1421&start=465

Drafts  of Boris B:

http://narod.ru/disk/9861644000/%D0%A6%D0%B8%D1%80%D0%BA%D1%83%D0%BB%D1%8F%D1%80%D0%BA%D0%B0.rar.html

As compared to initial drafts  the diameter of semimuffs is diminished on 6 mm, that they did not come

forward for the sizes of holder.

post-215-0-77305700-1363380502_thumb.jpg

Best regards,

Garward

 

 

Is under construction Montanes

 

Ready models Golden Star Corsair San Francisco II

Bronze 24-pdr canone Le Fleuron

Bronze 24-pdr canone Le Fleuron (second version)

Link to comment
Share on other sites

A motor is used by power 370 watts (descriptions on a photo 12) ot an aquatic pump. The details of drive  are shown on a photo 13 – 14. On the photo of 13А is a form from hardening on air plasticine, in which from silicon a cross-piece was made for semimuffs.

post-215-0-97203900-1363381152.jpg

Best regards,

Garward

 

 

Is under construction Montanes

 

Ready models Golden Star Corsair San Francisco II

Bronze 24-pdr canone Le Fleuron

Bronze 24-pdr canone Le Fleuron (second version)

Link to comment
Share on other sites

On a photo 15 – 17 the details of fastening to the table and moving of support are shown (sending). A screw is used by a diameter 12 mm with the special screw-thread, one turn of which is provided by the smooth moving of carriage with support on 12 mm along a table  (screw ot a scanning device for the exact positioning  of sensor on the surface of the controlled object at ultrasonic control).

post-215-0-84730900-1363382354.jpg

Best regards,

Garward

 

 

Is under construction Montanes

 

Ready models Golden Star Corsair San Francisco II

Bronze 24-pdr canone Le Fleuron

Bronze 24-pdr canone Le Fleuron (second version)

Link to comment
Share on other sites

Material the knot of drive – steel ст 45, details of fastening of an emphasis to a table - duralumin Д16Т in the thickness of 15 mm, an emphasis (directing) section 16х20 mm from Д16Т, a carriage clamp - Д16Т, the screw in clamp М6 from ст 45, a clamp axis - a steel  in diameter 6 mm. The engine costs on rubber linings in the initial thickness of 10 mm, rubber linings are established also on basis legs, their fastening to the basis and under bolts of fastening of the engine.

    On a photo 18 - 24 fastening the knot of drive to the engine and to the basis is shown. A rack of fastening of a flange (central) 200х105х8 mm from Д16Т, screws of fastening of flange М8, an intermediate rack - plywood of 24 mm (2х12 mm), lateral racks - plywood of 12 mm, fixing corners - a steel of 2 mm, screws M5.

post-215-0-17474400-1363382604.jpg

Best regards,

Garward

 

 

Is under construction Montanes

 

Ready models Golden Star Corsair San Francisco II

Bronze 24-pdr canone Le Fleuron

Bronze 24-pdr canone Le Fleuron (second version)

Link to comment
Share on other sites

On a photo 25 - 26 are shown cutting disks in diameter 63, 80 and 115 mm (the cores the sizes assumed to the use). In general the design is calculated on application of disks with the maximum diameter 160 mm. 

post-215-0-86341000-1363383642.jpg

Best regards,

Garward

 

 

Is under construction Montanes

 

Ready models Golden Star Corsair San Francisco II

Bronze 24-pdr canone Le Fleuron

Bronze 24-pdr canone Le Fleuron (second version)

Link to comment
Share on other sites

Continuation

 

That is shown on a photo 18 - 26, is the cutting block to which it is possible to attach easily tables of the various sizes and designs depending on requirements (for example, with the emphasis fixed on a surface for manufacturing of gratings, etc.).

Best regards,

Garward

 

 

Is under construction Montanes

 

Ready models Golden Star Corsair San Francisco II

Bronze 24-pdr canone Le Fleuron

Bronze 24-pdr canone Le Fleuron (second version)

Link to comment
Share on other sites

On a photo 27 - 30 the design a table is shown: actually a table 380х330х5 mm from Д16Т, a corner from Д16Т on a back part - directing for moving and fixing of a back part of an emphasis, a corner from Д16Т on a lateral part - for protractor moving (oblique-angled cutting).

post-215-0-52481700-1363383903.jpg

Best regards,

Garward

 

 

Is under construction Montanes

 

Ready models Golden Star Corsair San Francisco II

Bronze 24-pdr canone Le Fleuron

Bronze 24-pdr canone Le Fleuron (second version)

Link to comment
Share on other sites

On a photo 31 - 34 the design for start change a disk by table lifting is shown. The nut which is carrying out lifting, is fixed in a holder from Д16Т by screw M6.

post-215-0-19271100-1363385018.jpg

Best regards,

Garward

 

 

Is under construction Montanes

 

Ready models Golden Star Corsair San Francisco II

Bronze 24-pdr canone Le Fleuron

Bronze 24-pdr canone Le Fleuron (second version)

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...