And one more: Ropewalk for Miniature Ropes

[wefalck]

Well-made ropes in diametres below 0.5 mm are rather scarce or unavailable at all commercially or only in a few sizes and colours. So serious  miniature shipmodeller has to resort to make his own. There are various descriptions of ropewalks in the modelling literature and on the Internet to be found.

 

Essentially, a ropewalk consists of a headstock with a planetary drive the gives the individual strands a twist against the 'lay' of the rope, while at the other end there is a tailstock drive that twist the rope together. A travelling bobbin (the denomination varies) ensures that the strands are separated and then fed together in a controlled fashion. However, Bernard Frölich (1999) suggested that, when one keeps the strands apart at the tailstock end and then twists them together, the rope will start forming from the middle of the walk, progressing towards the headstock and tailstock. It is this principle that was used for the miniature ropewalk.

 

 

 

In my late fathers estate there was an optical bench with several 'steadies'. The bed is triangular in cross-section and is, as the steadies, made from solid dark-brown bakelite. It dates probably to the 1940s and was supplied by the well known German demonstration instrument company PHYWE. Not sure what my father would say about this new use, but after decades of slumbering in a dark corner of his study, it was calling for a new lease of life. It appeared to be a good base for a ropewalk and perhaps later also a serving machine, if I ever should need one.

 

Apart from the gears that were mostly bought for the purpose, the ropewalk was constructed from pieces found in my scrap-box. The design evolved while I was assembling it, so some aspects are not as well thought-out as I would wish. For instance, for the headstock I should have purchased six pinions and installed them permanently in a hexagon. I was too mean and bought only four.

 

 

 

The body of head- and tailstock is a small slab of 6 mm brass. The holes for the shafts were drilled and reamed to size. On the side that would have to take up the pull of the rope a 90° cone was sunk to create effectively half a cone bearing. This a better defined position than just a cylindrical bearing. The driving shaft in the headstock was left somewhat protruding to allow fixing at a later date a clamp for holding very thin wires for twisting them together. The hooks were bent from iron wire and hard-soldered into the shafts, as were the hooks in the driving plate of the tailstock. The driving shaft of the tailstock can be blocked by a thumbscrew that acts on a small brass pad, but the very thin ropes that I am making do not exert that much torque, so this may have been not necessary.

 

The steadies of an optical bench are not meant to travel, they are just set by a thumb-screw that screws into a triangular groove of the bed. However, the tailstock of a ropewalk has to move to allow for the shortening of the strands and the rope while being twisted together. I added round gibs made from aluminium rod. Round because I was to lazy to reproduce the odd triangular shape of the grooves. The tailstock is eased by hand to allow for the shortening because the rather long stems of the steadies lead to canting and thence to breaking of the very delicate ropes.

 

Depending on the direction of cranking, left- and right-handed rope with three or four strands can be made.

 

Reference

FRÖLICH, B. (1999): L'Art du modélisme.- 304 p., Nice (Editions Ancre).

 

wefalck

 

[michael mott]

Oooh that looks like a gem.

 

Michael

[fabius.b]

This is a little masterpiece.

I'm amazed....

[sonicmcdude]

This is the ultimate homemade tool. I mean really is made entirely from metal!  and is looking so nice. I mean you can manufacture this and sell them as pies     

[dgbot]

Great looking tool.  I bet you had fun building it.

David B

[Redbeard]

I want one...

[wefalck]

Make one ... I had contemplated using a curtain rail as the basis, before the optical bench came my way. Many people use wooden boards and threaded rod for the bodies. All can be done with a hand-saw and a drill-press. The ropewalks of old also were not pieces of precision engineering (ignoring the big industrial ones, such as the one in Chatham Dockyard).

 

Mine was designed for making ropes from extra-thin fly-tying silk.

 

wefalck