fxitgood Posted January 27, 2015 Share #1 Posted January 27, 2015 Hello, Never built a sailing ship!!!!!!! Have completed the wooden hull, deck, masts. Have rigged the shrouds and ratlines. My question is what sequence should I do now and how do I attach sails to yardarms. Thank You. Very respectfully, Rich I am working on USS CONSITUTION 1797 Wooden Model Ship. Quote Link to comment Share on other sites More sharing options...
HIPEXEC Posted January 27, 2015 Share #2 Posted January 27, 2015 I'm trying to figure that out right now. I slippfitted the sails on to the yards while I figure out the sequence, Quote Rich Rich USS Constitution by hipexec (Finished build) Virginia Pilot Boat 1805 (gallery - first build) USS Syren (USS Argus) by Hipexec Joshua Slocum's Spray by HIPEXEC Link to comment Share on other sites More sharing options...
JerseyCity Frankie Posted January 27, 2015 Share #3 Posted January 27, 2015 Work from the deck up and from the bow out. Masts and bowsprit consist of three or more individual units that rise one upon the other getting more slender as they stack up farther from the deck. All these parts have specific names and all the rigging that will go on the spars also have individual names- and on the real ship they all performed specific functions. Its going to be very difficult to learn all this but on the other hand if you get some ship model building books you will find all the information there. Plus there are a LOT of build logs here on Model Ship World that go from a bare hull to a completed ship, most of these with step by step photos with detailed written comments. There are a LOT of USS Constitution build logs to chose from and you will have no trouble at all finding photos of every step of the rigging process. Quote Quote Niagara USS Constitution Link to comment Share on other sites More sharing options...
Tadeusz43 Posted January 27, 2015 Share #4 Posted January 27, 2015 Hi, Short Guide to period ship model rigging. After hull finishing and mast installation is time for „spider works” it is rigging. All belaying racks , cleats must be already installed also is recommended to install eye bolts on ship decks or drill holes for it . My sequence is: 1.Standing rigging – stays , shrouds, backstays, bowsprit standing rigging. I start with this works from foremast down shrouds and proceed going up and next to stern. With proper tension of shrouds, stays and backstays position of mast is adjusted. This is very important to control position of masts using plumb-line. 2.Yards furnishing. I install blocks and standing rigging on yards as also yard’s truss or parral. After fully furnishing of yards is time for attaching sails and running rigging: lifts, clew lines, leech and bunt lines, reef tackles Next is time for attach sails to the yards. 3. Yards with sails are installed on masts and required running rigging is made - from topmast sails going down. 4. Remaining running rigging is installed: sheets and tacks, braces. With proper tensions of sheets, tacks and braces the yards are shifted into required position. Tension of bowlines can help form bunt of sails. Foto 1-9 Rigging workshop and jigs Foto 10-12 Deadeyes tyig and jig Foto 13 Ratlines tying with use of upholstery needle and stencil. Foto 14-16 Yards and sails ready for "weddin" Foto 16-18 Jigs for blocks tying and tackle made Recommended books: Rigging Period Ship Models by Lennarth Petersson Rigging Period Fore-and-Aft Craft by Lennarth Petersson Historic Ship Models b y Wolfram zu Mondfeld Tadeusz cristikc, BobG, tkay11 and 4 others 7 Quote Link to comment Share on other sites More sharing options...
robnbill Posted January 27, 2015 Share #5 Posted January 27, 2015 (edited) Welcome to the forum. Who is the model manufacturer's you are building? The davits look like it might be the Constructo? Each model has it's own strong and weak points. If we know the manufacturer it narrows things down a bit. Edited January 27, 2015 by robnbill Quote Bill Chantilly, VA Its not the size of the ship, but the bore of the cannon! Current Build: Scratch Build Brig Eagle Completed Build Log: USS Constitution - Mamoli Completed Build Gallery: USS Constitution - Mamoli Link to comment Share on other sites More sharing options...
fxitgood Posted January 28, 2015 Author Share #6 Posted January 28, 2015 yes Constructo Wooden Model Kit. Thank you Quote Link to comment Share on other sites More sharing options...
robnbill Posted January 28, 2015 Share #7 Posted January 28, 2015 You and Rich (Hipexec) are building the same model. I just finished the Mamoli version. Most people here are building the Model Shipways version. However, if you follow the logs you will see that everyone has a slightly different take on how they like to do the rigging. I would read the logs and see which way you want to do it. There are also a number of good books on the subject. Tadeuz listed most of them. I would also add "The 44-Gun Frigate USS Constitution, "Old Ironsides" (Anatomy of the Ship)" by Karl Heinz Marquardt. There are a number of mistakes and inconsistencies in the AOS but it makes a good reference point along with all the other references on the ship. Of course the Navy site and the museum website are also great sources of information. She is a fun ship with a great history and the first one that I really rigged. Luckily for me the Mamoli plans walked me step by step through most of it. Quote Bill Chantilly, VA Its not the size of the ship, but the bore of the cannon! Current Build: Scratch Build Brig Eagle Completed Build Log: USS Constitution - Mamoli Completed Build Gallery: USS Constitution - Mamoli Link to comment Share on other sites More sharing options...
fxitgood Posted March 9, 2015 Author Share #8 Posted March 9, 2015 When rigging a 3 mast sailing ship is it better / easier to attach all the lines to the deck and leave them long to attach to sails and yardarms later? georgekienstra@yahoo.co.uk 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.