ancre Le Fleuron by cabrapente - FINISHED

[cabrapente]

more

[cabrapente]

December 23: in mid-November, I started coughing, I think for the sawdust powder. that cough, I broke the ribs and I've been on bed rest until I started rehabilitation today.

and soon, when I have a little more mobility, we are acting up again.

until then: Merry Christmas and happy holidays to all.

Edited February 19, 2013 by cabrapente

[cabrapente]

February 4: In these days of inactivity, I have given much thought and melon and think I've found the key when placing the ties of hawse.

I take the point to all parts. (green line and orange)

[cabrapente]

at the height of the lines, I will move away from the start of the angle, to the outside of the piece.

the transfer to the wooden wedges, previously, I have seen totaling 90 degrees.

[cabrapente]

thus leaving all the first.

mount when he left the paper, which would serve to unstuck once sanded.

anyway, if there is a problem, we can always add a wedge instead of a whole piece, which cover all the gaps.

[cabrapente]

April 7: Well here we are again. physiotherapist says that in two weeks, term rehabilitation.

when I had the accident, I did several things wrong: Cut pieces of frames too tight, and that allows few adjustments when sanding.

rode the town in record time, using only one arm, and inserting dowels between frames to give rigidity.

these tacos, squeezed to remove excess and tier ship once sanding, I encounter a big problem of destruction.

short: as I could, I removed almost all the frames, and I'm starting again.

[Garward]

Good work! 

[cabrapente]

Now, I'm riding the frames out of the stands.

I use a ribbon, like a compass, so that they are at the same distance

[cabrapente]

to keep the frames in place, I made ​​some "cats" with wire and rubber.

[cabrapente]

mounting the poop deck

[cabrapente]

Well, he was afraid of this piece, but it went well.

[cabrapente]

more

[cabrapente]

small carvings and moldings

I start lining

[cabrapente]

with bike camera straps, and a stop serving sticks, grabbed the sleepers, faster than with cats and non-obtrusive to manipulate the boat

[cabrapente]

tables, folded wetting and applying heat with the iron.

when I turned 5, and not burn. hehe

[cabrapente]

I had to remove everything, as I this deforming the hull. (again grief issues).

tapes begin to give rigidity.

tapes are very thick, and even bend them, recover the form.

I gave cuts inside and it works.

[cabrapente]

more sizes

[cabrapente]

the ports of the first cover with batiportes.

 

I got a log of what I have orange and cut into 4 planks.

tables out of a very pretty yellow.

[cabrapente]

 purchased online a "scratch". eat a lot, but it is a very fine finish, so I made ​​aI have prepared a sand, egg-shaped, to sand curved areas. loop with velcro sanding.

[cabrapente]

the term "oblique vaigrage".I've had the tapes with bitumen.

tape down the sanding I and kills some brightness.

[cabrapente]

I cut all the pieces of the webs.

FISO've joined with tables, and short pieces in pairs.

[cabrapente]

finished interior.

[cabrapente]

I start with the beams

[cabrapente]

earlier, similar to buying a Proxxon, but the leaves are leaving with great ease and cost 18 euros.

Now I bought this in makro and it cost around 90 euros. with the advantage that it is much higher, and the production leaves me a man who makes them for professional carpenters.

cost between 7-10 euros, according to the paper.

I have removed some protections caps (which do not do that ...) and I get blocks cutting 10 cm.

I start with the interior

[cabrapente]

I start with the interior

[cabrapente]

stairs

[cabrapente]

I put the box of bombs.

[cabrapente]

I start the beams of the first cover

to place the beams, I fabricated "Styrofoam" some beams, which intersect with the simplest to cuter, can be bent, and at one point becomes one test, which you copied in wood

[cabrapente]

to pump more cash.

[cabrapente]

more