Jump to content

Ol' Pine Tar

Members
  • Content Count

    83
  • Joined

  • Last visited

About Ol' Pine Tar

  • Birthday 07/13/1946

Profile Information

  • Gender
    Male
  • Location
    East Texas
  • Interests
    amateur photography, model shipbuilding, stamp collecting

Recent Profile Visitors

642 profile views
  1. Completed planking the hull; doing some filling and sanding. The laser cut pre-spiled planks worked out quite well. Had to trim and/or taper the last few planks, but overall was OK. This is a nice kit. Stained and poly’d the deck sheets; Minwax “Gunstock” stain, satin Wipe-On Poly.
  2. Second planking layer.. needed just a bit of filler and sanding. Ready for third layer of planking. So far, so good. Impressed with the quality of everything in this kit. Thanks Dusek!
  3. Thank you Peter! First planking layer. The laser-cut planks worked fairly well. So far, so good...
  4. Uh-oh... First re-do... with the first planks secured, I realized the transom was mounted much too vertical, mainly because I failed to sshape the stern frames to the proper angle - not paying attention to plans? I did manage to remove it intact. I'm going to wait until I get more of the first layer of planking done before I start reshaping the stern frames and attaching the transom piece so I can get everything matched up. Continued the first planking layer...
  5. Thanks Chris! I'm a big fan of schooners too. For models, I much prefer these smaller vessels in larger scales. and... no guns to rig...😁
  6. Thanks GrandpaPhil and ccoyle for the "Likes" Began planking the first layer of pre-spiled planks. This first layer is of very thin plywood so no soaking. Gave them a bit of pre-curve with electric plank bender and left them clamped up overnight. So far I've been impressed with the quality of the materials and accuracy of the laser cutting, but I did notice some areas on some of the plywood sheets where the plies have separated. I made an attempt to inject some wood glue into the separations, and weight them down on a flat surface. Otherwise, no problems. After dry fitting several planks, I started the planking with the "b" plank so I can use the bulkhead extensions to hook rubber bands over for clamping if needed. With the pre-spiled planks, I saw no need to line off the hull, but I am curving and dry fitting 3 or 4 planks ahead of the one I'm gluing. This is also my first build with multiple planking layers - there are actually three layers in some areas. Instructions say to start at the top and work down so...
  7. Got the keel/frames assembly fitted and glued, and began fairing. All the parts fit together well.
  8. Punched out and cleaned up keel, frames, and reinforcements. Keel had a very minor warp and twist but wetting it a little and clamping it in the keel clamp seemed to take care of that. Dry fit is good with everything going together well with sufficient clearances but not too loose. I'm very pleased with the quality of the wood and accuracy of the laser cutting.
  9. I’ve been fiddlin’ around with model ships off and on for several years. Up to now, I’ve never really settled in and completed a display quality model ship. I’ve started a couple of build logs here on MSW; (1) Model Shipways Willie Bennett; which was almost completed but got lost somewhere moving, and (2) Model Shipways Fair American, which I still work on occasionally. I'm still relatively inexperienced so I’m always open to critique, comments, advice, and suggestions. Please don’t hesitate to jump in... About the kit… The Belle Poule (1932) kit is produced by Dusek Ship Kits. Not going to do the “what’s in the box” thing here as Dusek Ship Kits has posted an excellent “what’s in the box” video and Dirk (Dubz) posted a fine review of the kit and contents. First impressions: 1. There are a lot more laser cut parts and the wood appears to be of much better quality than I have seen in other kits. Its obvious that a lot of research, planning, and engineering has been done to produce this kit. 2. The plans and instructions appear to be adequate. I like that the plan sheets have layouts of the laser-cut parts sheets so you don’t have to sort through all the parts sheets when you’re looking for specific items. 3. I'm anxious to see how the laser-cut pre-spiled planking works out. Scale 1:50 Length: 755 mm (2923⁄32in) Width: 255 mm (103⁄64in ) Height: 655 mm (2525⁄32in About La Belle Poule… La Belle Poule (1932) is the fourth ship of the French Navy to bear the name. The modern Belle Poule, the subject of this kit, was launched on February 8, 1932, at Chantiers de Normandie at Fecamp, France, and is a replica of an Icelandic cod fishing vessel. She has a sister ship, Étoile. In 1940 she was seized by the British and served the Free French Forces during the Second World War. Since 1978, the Belle Poule has been sponsored by the city of Pauillac, France and underwent an extensive renovation and restoration in 2017. La Belle Poule is 123’ long, a beam of 24’ and has displacement 225 tons. Powered by sail and a 285 hp diesel engine, the ship is able to sail up to 12.5 knots under sail and up to 9 knots powered by diesel engine. She still maintains a very active sailing schedule.
  10. Received in good order today... Ordered from Model Expo about 3 weeks ago - Labor Day Weekend sale. Thanks Model Expo!
  11. Thanks JPam. Yes, the gun ports were the cause of most of my miseries. I think I've got that problem solved. And, once again, I've been going through all the FA build logs on MSW and still finding a lot of good advice. Thanks for commenting!
  12. Thanks Don. The gallows, bits and binnacle are wood. Gallows are from the kit and the bits and binnacle scratchbuilt. The capstan and anchors are kit castings. I'll probably replace several of the castings with scratchbuilt stuff.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem

Modelshipworld - Advancing Ship Modeling through Research
×
×
  • Create New...